tlpCoolingFanSpeed

TRIPPLITE-PRODUCTS · .1.3.6.1.4.1.850.1.1.3.5.5.1.1.2
MIB view Table view

Object

column r/w Enumeration 
Specifies the actual speed of the evaporator fan. Setting the fan speed 
to auto(6) will enable tlpCoolingAutoFanSpeed; however, on most units getting 
the fan speed will return the actual fan speed regardless whether auto fan 
speed is enabled or disabled. The value auto(6) is returned only on units that 
do not report the actual fan speed when auto fan speed is enabled. Not all 
values are supported on all cooling units. Invalid values will return an appropriate
error when accessed. If not supported, this value will always return ERROR_NO_SUCH_NAME

Context

MIB
TRIPPLITE-PRODUCTS
OID
.1.3.6.1.4.1.850.1.1.3.5.5.1.1.2
Type
column
Access
readwrite
Status
current
Parent
tlpCoolingConfigEntry
Table
tlpCoolingConfigTable
Siblings
24

Syntax

Enumeration

Values & Constraints

Enumerated Values
0off
1low
2mediumLow
3medium
4mediumHigh
5high
6auto

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
tlpCoolingAutoStart
Specifies if the unit should start automatically on power up. If not supported, this value will always return ERROR_NO_SUCH_NAME.
columnEnumeration.1.3.6.1.4.1.850.1.1.3.5.5.1.1.1
tlpCoolingOffOnInputContact
Indicates if the unit should stop cooling when input contact is activated. If not supported, this value will always return ERROR_NO_SUCH_NAME.
columnEnumeration.1.3.6.1.4.1.850.1.1.3.5.5.1.1.10
tlpCoolingOffOnLeak
Indicates if the unit should stop cooling when leak input is activated. If not supported, this value will always return ERROR_NO_SUCH_NAME.
columnEnumeration.1.3.6.1.4.1.850.1.1.3.5.5.1.1.11
tlpCoolingWaterLeakContactType
The water leak contact type. If not supported, this value will always return ERROR_NO_SUCH_NAME.
columnEnumeration.1.3.6.1.4.1.850.1.1.3.5.5.1.1.12
tlpCoolingAirFilterInterval
The number of weeks before the air filter needs to be changed. If not supported, this value will always return ERROR_NO_SUCH_NAME.
columnweeks SNMPv2-SMIUnsigned32.1.3.6.1.4.1.850.1.1.3.5.5.1.1.13
tlpCoolingAirFilterAlarm
When enabled, an alarm should occur when the maximum number of air filter run hours has been exceeded. If not supported, this value will always return ERROR_NO_SUCH_NAME.
columnhours Enumeration.1.3.6.1.4.1.850.1.1.3.5.5.1.1.14
tlpCoolingMaxAirFilterRunHours
The maximum interval for air filter run hours before warning is annunciated. If not supported, this value will always return ERROR_NO_SUCH_NAME.
columnhours SNMPv2-SMIUnsigned32.1.3.6.1.4.1.850.1.1.3.5.5.1.1.15
tlpCoolingStartTimer
The unit will start operate after the specified timer elapsed. If not supported, this value will always return ERROR_NO_SUCH_NAME.
columnminutes SNMPv2-SMIUnsigned32.1.3.6.1.4.1.850.1.1.3.5.5.1.1.16
tlpCoolingStopTimer
The unit will switch to standby mode after the specified timer elapsed. If not supported, this value will always return ERROR_NO_SUCH_NAME.
columnminutes SNMPv2-SMIUnsigned32.1.3.6.1.4.1.850.1.1.3.5.5.1.1.17
tlpCoolingEnergyMode
This option enables or disables the energy saving mode. If not supported, this value will always return ERROR_NO_SUCH_NAME.
columnEnumeration.1.3.6.1.4.1.850.1.1.3.5.5.1.1.18
tlpCoolingDefrostMode
This option enables or disables the defrost mode. If not supported, this value will always return ERROR_NO_SUCH_NAME.
columnEnumeration.1.3.6.1.4.1.850.1.1.3.5.5.1.1.19
tlpCoolingRemoteTemperatureSensor
This option enables or disables the remote temperature sensor. If not supported, this value will always return ERROR_NO_SUCH_NAME.
columnEnumeration.1.3.6.1.4.1.850.1.1.3.5.5.1.1.20
tlpCoolingDehumidifyingMode
This option enables or disables the dehumidifying mode. If not supported, this value will always return ERROR_NO_SUCH_NAME.
columnEnumeration.1.3.6.1.4.1.850.1.1.3.5.5.1.1.21
tlpCoolingFanAlwaysOn
This option enables or disables the fan always on. If not supported, this value will always return ERROR_NO_SUCH_NAME.
columnEnumeration.1.3.6.1.4.1.850.1.1.3.5.5.1.1.22
tlpCoolingQuietMode
This option enables or disables the quiet mode. If not supported, this value will always return ERROR_NO_SUCH_NAME.
columnEnumeration.1.3.6.1.4.1.850.1.1.3.5.5.1.1.23
tlpCoolingHotGasBypass
This option enables or disables the hot gas bypass. If not supported, this value will always return ERROR_NO_SUCH_NAME.
columnEnumeration.1.3.6.1.4.1.850.1.1.3.5.5.1.1.24
tlpCoolingAutoFanSpeed
This option enables or disables the auto fan speed. If not supported, this value will always return ERROR_NO_SUCH_NAME.
columnEnumeration.1.3.6.1.4.1.850.1.1.3.5.5.1.1.25
tlpCoolingControlType
Specifies which temperature is used as a control point. If not supported, this value will always return ERROR_NO_SUCH_NAME.
columnEnumeration.1.3.6.1.4.1.850.1.1.3.5.5.1.1.3
tlpCoolingDisplayUnits
Specifies whether displays output values in Metric or English formats. If not supported, this value will always return ERROR_NO_SUCH_NAME.
columnEnumeration.1.3.6.1.4.1.850.1.1.3.5.5.1.1.4
tlpCoolingBeepOnKey
Specifies whether a beep is emitted when a key is pressed on the unit's display panel. If not supported, this value will always return ERROR_NO_SUCH_NAME.
columnEnumeration.1.3.6.1.4.1.850.1.1.3.5.5.1.1.5
tlpCoolingInputContactType
The input contact type. If not supported, this value will always return ERROR_NO_SUCH_NAME.
columnEnumeration.1.3.6.1.4.1.850.1.1.3.5.5.1.1.6
tlpCoolingOutputContactType
The output contact type. If not supported, this value will always return ERROR_NO_SUCH_NAME.
columnEnumeration.1.3.6.1.4.1.850.1.1.3.5.5.1.1.7
tlpCoolingOutputRelaySource
The alarm level that causes the output relay to activate. If not supported, this value will always return ERROR_NO_SUCH_NAME.
columnEnumeration.1.3.6.1.4.1.850.1.1.3.5.5.1.1.8
tlpCoolingOutputRelayDefault
Type of contact to make when output relay is activated. If not supported, this value will always return ERROR_NO_SUCH_NAME.
columnEnumeration.1.3.6.1.4.1.850.1.1.3.5.5.1.1.9