sfpTemperature

SIAE-SFP-MIB · .1.3.6.1.4.1.3373.1103.74.7.1.6
MIB view Table view

Object

column C/10 Temperature 
This contains the internal temperature of the SFP in tehnth of 
Celsius degrees. Range is from -128.0C to +128.0C, but is only
valid from -40.0C to +125.0C with an accuracy of +/- 3C. 
Located at I2C address 0xa2, Bytes 96 & 97 (MSB, LSB)

Context

MIB
SIAE-SFP-MIB
OID
.1.3.6.1.4.1.3373.1103.74.7.1.6
Type
column
Access
readonly
Status
current
Units
C/10
Parent
sfpDiagnosticEntry
Table
sfpDiagnosticTable
Siblings
11

Syntax

C/10 Temperature
Source
Temperature
Base type
Integer32

Values & Constraints

Type Constraints
range: -2000..2000

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
sfpDiagnosticValid
if False, then the SFP data in this table is not valid. This will be set to False if the SFP module is not installed, or if the I/O card that contains the SFP is not installed or …
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.3373.1103.74.7.1.1
sfpRxPower
This contains the internally measured RX optical power. Units are in uW (micro Watts), and range from 0 to 6554uW (6.535mW). Located at I2C address 0xa2, Bytes 104 & 105 (MSB, LSB)
columnmicroWatts (uW) Integer32.1.3.6.1.4.1.3373.1103.74.7.1.10
sfpInternalAlarms
This contains the state of the SFP internal alarm register. A bit is set for each alarm that is active. located at I2C address 0xa2, Byte 112 & 113 (MSB, LSB) mask 0xffc0
columnBits.1.3.6.1.4.1.3373.1103.74.7.1.11
sfpInternalWarnings
This contains the state of the SFP internal warning register. A bit is set for each warning that is active. located at I2C address 0xa2, Byte 116 & 117 (MSB, LSB) mask 0xffc0
columnBits.1.3.6.1.4.1.3373.1103.74.7.1.12
sfpLOSPinOut
This contains the T/F state of the SFP LOS (output) pin. It is True if the SFP has detected Loss-Of-Signal. located at I2c address 0xa2, address: 110, mask 0x02
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.3373.1103.74.7.1.2
sfpTxFaultPinOut
This contains the T/F state of the SFP Tx Fault (output) pin. It is True if the SFP has detected a Tx fault condition. located at I2C address 0xa2, Byte 110, mask 0x04
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.3373.1103.74.7.1.3
sfpRateSelectPinIn
This contains the T/F state of the SFP RX Rate Select (input) pin. This function is not implemented on Finisar SFPs. located at I2C address 0xa2, Byte 110, mask 0x10
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.3373.1103.74.7.1.4
sfpTxDisablePinIn
This contains the T/F state of the SFP TX Disable (input) pin. located at I2C address 0xa2, Byte 110, mask 0x80
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.3373.1103.74.7.1.5
sfpVoltage
This contains the internally measured SFP supply voltage (Vcc). Units are in milliVolts (3210 = 3.21V). Range is 0 to 6.554V. Located at I2C address 0xa2, Bytes 98 & 99 (MSB, LSB)
columnmilliVolts (mV) Integer32.1.3.6.1.4.1.3373.1103.74.7.1.7
sfpTxBias
This contains the internally measured SFP TX laser bias current. Units are in microAmps, and range from 0 to 131000uA (131mA). Located at I2C address 0xa2, Bytes 100 & 101 (MSB, L…
columnmicroAmps (uA) Integer32.1.3.6.1.4.1.3373.1103.74.7.1.8
sfpTxPower
This contains the internally measured TX output power. Units are in uW (micro Watts), and range from 0 to 6554uW (6.535mW). This value is not valid if the transmitter is disabled.…
columnmicroWatts (uW) Integer32.1.3.6.1.4.1.3373.1103.74.7.1.9