sfpDiagnosticValid
SIAE-SFP-MIB ·
.1.3.6.1.4.1.3373.1103.74.7.1.1
Object
column
SNMPv2-TCTruthValue
if False, then the SFP data in this table is not valid. This will be set to False if the SFP module is not installed, or if the I/O card that contains the SFP is not installed or if the EEPROM check code is wrong. The data in the table should not be used unless this element is True.
Context
- MIB
- SIAE-SFP-MIB
- OID
.1.3.6.1.4.1.3373.1103.74.7.1.1- Type
- column
- Access
- readonly
- Status
- current
- Parent
- sfpDiagnosticEntry
- Table
- sfpDiagnosticTable
- Siblings
- 11
Values & Constraints
Type Values
1 | true |
2 | false |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| sfpRxPower This contains the internally measured RX optical power. Units
are in uW (micro Watts), and range from 0 to 6554uW (6.535mW).
Located at I2C address 0xa2, Bytes 104 & 105 (MSB, LSB) | column | microWatts (uW) Integer32 | .1.3.6.1.4.1.3373.1103.74.7.1.10 |
| sfpInternalAlarms This contains the state of the SFP internal alarm register. A
bit is set for each alarm that is active. located at I2C
address 0xa2, Byte 112 & 113 (MSB, LSB) mask 0xffc0 | column | Bits | .1.3.6.1.4.1.3373.1103.74.7.1.11 |
| sfpInternalWarnings This contains the state of the SFP internal warning register.
A bit is set for each warning that is active. located at I2C
address 0xa2, Byte 116 & 117 (MSB, LSB) mask 0xffc0 | column | Bits | .1.3.6.1.4.1.3373.1103.74.7.1.12 |
| sfpLOSPinOut This contains the T/F state of the SFP LOS (output) pin. It is
True if the SFP has detected Loss-Of-Signal. located at I2c
address 0xa2, address: 110, mask 0x02 | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.3373.1103.74.7.1.2 |
| sfpTxFaultPinOut This contains the T/F state of the SFP Tx Fault (output) pin.
It is True if the SFP has detected a Tx fault condition.
located at I2C address 0xa2, Byte 110, mask 0x04 | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.3373.1103.74.7.1.3 |
| sfpRateSelectPinIn This contains the T/F state of the SFP RX Rate Select (input)
pin. This function is not implemented on Finisar SFPs. located
at I2C address 0xa2, Byte 110, mask 0x10 | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.3373.1103.74.7.1.4 |
| sfpTxDisablePinIn This contains the T/F state of the SFP TX Disable (input) pin.
located at I2C address 0xa2, Byte 110, mask 0x80 | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.3373.1103.74.7.1.5 |
| sfpTemperature This contains the internal temperature of the SFP in tehnth of
Celsius degrees. Range is from -128.0C to +128.0C, but is only
valid from -40.0C to +125.0C with an accuracy of +/-… | column | C/10 Temperature | .1.3.6.1.4.1.3373.1103.74.7.1.6 |
| sfpVoltage This contains the internally measured SFP supply voltage
(Vcc). Units are in milliVolts (3210 = 3.21V). Range is 0 to
6.554V. Located at I2C address 0xa2, Bytes 98 & 99 (MSB, LSB) | column | milliVolts (mV) Integer32 | .1.3.6.1.4.1.3373.1103.74.7.1.7 |
| sfpTxBias This contains the internally measured SFP TX laser bias
current. Units are in microAmps, and range from 0 to 131000uA
(131mA). Located at I2C address 0xa2, Bytes 100 & 101 (MSB, L… | column | microAmps (uA) Integer32 | .1.3.6.1.4.1.3373.1103.74.7.1.8 |
| sfpTxPower This contains the internally measured TX output power. Units
are in uW (micro Watts), and range from 0 to 6554uW (6.535mW).
This value is not valid if the transmitter is disabled.… | column | microWatts (uW) Integer32 | .1.3.6.1.4.1.3373.1103.74.7.1.9 |