dsx3LineIndex
RFC1407-MIB ·
.1.3.6.1.2.1.10.30.5.1.1
Object
column
IF-MIBInterfaceIndex
This object should be made equal to ifIndex. The
next paragraph describes its previous usage.
Making the object equal to ifIndex allows proper
use of ifStackTable.
Previously, this object was the identifier of a
DS3/E3 Interface on a managed device. If there is
an ifEntry that is directly associated with this
and only this DS3/E3 interface, it should have the
same value as ifIndex. Otherwise, number the
dsx3LineIndices with an unique identifier
following the rules of choosing a number that is
greater than ifNumber and numbering the inside
interfaces (e.g., equipment side) with even
numbers and outside interfaces (e.g., network side)
with odd numbers.
Context
- MIB
- RFC1407-MIB
- OID
.1.3.6.1.2.1.10.30.5.1.1- Type
- column
- Access
- readonly
- Status
- current
- Parent
- dsx3ConfigEntry
- Table
- dsx3ConfigTable
- Siblings
- 17
Values & Constraints
Type Constraints
range: 1..2147483647
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| dsx3LineStatus This variable indicates the Line Status of the
interface. It contains loopback state information
and failure state information. The dsx3LineStatus
is a bit map represented as a … | column | Integer32 | .1.3.6.1.2.1.10.30.5.1.10 |
| dsx3TransmitClockSource The source of Transmit Clock.
loopTiming indicates that the recovered receive
clock is used as the transmit clock.
localTiming indicates that a local… | column | Enumeration | .1.3.6.1.2.1.10.30.5.1.11 |
| dsx3InvalidIntervals The number of intervals in the range from 0 to
dsx3ValidIntervals for which no data is available.
This object will typically be zero except in cases
where the data for some interv… | column | Integer32 | .1.3.6.1.2.1.10.30.5.1.12 |
| dsx3LineLength The length of the ds3 line in meters. This
object provides information for line build out
circuitry if it exists and can use this object to
adjust the line build out. | column | meters Integer32 | .1.3.6.1.2.1.10.30.5.1.13 |
| dsx3LineStatusLastChange The value of MIB II's sysUpTime object at the
time this DS3/E3 entered its current line status
state. If the current state was entered prior to
the last re-initialization of the … | column | SNMPv2-TCTimeStamp | .1.3.6.1.2.1.10.30.5.1.14 |
| dsx3LineStatusChangeTrapEnable Indicates whether dsx3LineStatusChange traps
should be generated for this interface. | column | Enumeration | .1.3.6.1.2.1.10.30.5.1.15 |
| dsx3LoopbackStatus This variable represents the current state of the
loopback on the DS3 interface. It contains
information about loopbacks established by a
manager and remotely from the far end.
… | column | Integer32 | .1.3.6.1.2.1.10.30.5.1.16 |
| dsx3Channelization Indicates whether this ds3/e3 is channelized or
unchannelized. The value of enabledDs1 indicates
that this is a DS3 channelized into DS1s. The
value of enabledDs3… | column | Enumeration | .1.3.6.1.2.1.10.30.5.1.17 |
| dsx3Ds1ForRemoteLoop Indicates which DS1/E1 on this DS3/E3 will be
indicated in the remote ds1 loopback request. A
value of 0 means no DS1 will be looped. A value
of 29 means all DS1s/E1s will be lo… | column | Integer32 | .1.3.6.1.2.1.10.30.5.1.18 |
| dsx3IfIndex deprecated This value for this object is equal to the value
of ifIndex from the Interfaces table of MIB II
(RFC 1213). | column | IF-MIBInterfaceIndex | .1.3.6.1.2.1.10.30.5.1.2 |
| dsx3TimeElapsed The number of seconds that have elapsed since the
beginning of the near end current error-
measurement period. If, for some reason, such as
an adjustment in the sys… | column | Integer32 | .1.3.6.1.2.1.10.30.5.1.3 |
| dsx3ValidIntervals The number of previous near end intervals for
which data was collected. The value will be 96
unless the interface was brought online within the
last 24 hours, in which case the v… | column | Integer32 | .1.3.6.1.2.1.10.30.5.1.4 |
| dsx3LineType This variable indicates the variety of DS3 C-bit
or E3 application implementing this interface. The
type of interface affects the interpretation of
the usage and error statistics.… | column | Enumeration | .1.3.6.1.2.1.10.30.5.1.5 |
| dsx3LineCoding This variable describes the variety of Zero Code
Suppression used on this interface, which in turn
affects a number of its characteristics.
dsx3B3ZS and e3HDB3 refer to the use of… | column | Enumeration | .1.3.6.1.2.1.10.30.5.1.6 |
| dsx3SendCode This variable indicates what type of code is
being sent across the DS3/E3 interface by the
device. (These are optional for E3 interfaces.)
Setting this variable causes the interf… | column | Enumeration | .1.3.6.1.2.1.10.30.5.1.7 |
| dsx3CircuitIdentifier This variable contains the transmission vendor's
circuit identifier, for the purpose of
facilitating troubleshooting. | column | OctetString | .1.3.6.1.2.1.10.30.5.1.8 |
| dsx3LoopbackConfig This variable represents the desired loopback
configuration of the DS3/E3 interface.
The values mean:
dsx3NoLoop
Not in the loopback state. A device that is
no… | column | Enumeration | .1.3.6.1.2.1.10.30.5.1.9 |