rcPortBrouterVrfId

RC-PORT-MIB · .1.3.6.1.4.1.2272.1.4.10.1.1.97
MIB view Table view

Object

column r/w RC-VRF-MIBVrfIdentifier 
Gives the VRF Id for this Brouter port.

Context

MIB
RC-PORT-MIB
OID
.1.3.6.1.4.1.2272.1.4.10.1.1.97
Type
column
Access
readwrite
Status
current
Parent
rcPortEntry
Table
rcPortTable
Siblings
127

Syntax

RC-VRF-MIBVrfIdentifier
Source
RC-VRF-MIBVrfIdentifier
Base type
Unsigned32

Values & Constraints

Type Constraints
range: 0..4294967295

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
rcPortIndex
An index value that uniquely identifies a port. This value is similar to ifIndex in MIB2.
columnIF-MIBInterfaceIndex.1.3.6.1.4.1.2272.1.4.10.1.1.1
rcPortBackupConnectorStatus
Indicate the status of the link attached to the back-up (non-active) connector.
columnEnumeration.1.3.6.1.4.1.2272.1.4.10.1.1.10
rcPortCtrlPktDropLimitEnable
Used to enable/disable Control Packets Drop Rate Limiter functionality.
columnRAPID-CITYEnableValue.1.3.6.1.4.1.2272.1.4.10.1.1.100
rcPortCtrlPktDropLimit
Indicates the Control Packet drop rate limit value
columnInteger32.1.3.6.1.4.1.2272.1.4.10.1.1.101
rcPortCtrlPktShutdownLimitEnable
Used to enable/disable Control Packets Shutdown Rate Limiter functionality.
columnRAPID-CITYEnableValue.1.3.6.1.4.1.2272.1.4.10.1.1.102
rcPortCtrlPktShutdownLimit
Indicates the Control Packet shutdown rate Limit value
columnInteger32.1.3.6.1.4.1.2272.1.4.10.1.1.103
rcPortCtrlPktShutdownRtExceeded
Indicates if the Shutdown rate has been exceeded on the port
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.10.1.1.104
rcPortCtrlPktDropRtExceeded
Indicates if the Drop rate has been exceeded on the port
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.10.1.1.105
rcPortDhcpOption82SubscriberId
This object contains the DHCP option 82 subscriber ID string to be used in sub-option 6. If the value is an empty string, then sub-option 6 is not included in option 82
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.2272.1.4.10.1.1.106
rcPortServiceCardType
Port Hardware type, which includes PowerRanger, ESM port and other
columnEnumeration.1.3.6.1.4.1.2272.1.4.10.1.1.107
rcPortIngressRatePeak
Peak rate limit for this port. 0 means disable.
columnInteger32.1.3.6.1.4.1.2272.1.4.10.1.1.108
rcPortIngressRateSvc
Service rate limit for this port. 0 means disable.
columnInteger32.1.3.6.1.4.1.2272.1.4.10.1.1.109
rcPortAutoNegotiate
Indicate whether this port enabled for auto negotiations or not.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.10.1.1.11
rcPortCpLimitPktRate
Used to limit Control packets on the port to qos-levels 6 and 7. Sets the limit in packets per second.
columnInteger32.1.3.6.1.4.1.2272.1.4.10.1.1.110
rcPortCpLimitShutDownEnable
Used to indicate if the port should be shutdown when the CpLimitPktRate is exceeded.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.10.1.1.111
rcPortRmonEnable
Used to set Remote Monitoring enable/disable
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.10.1.1.112
rcPortIpsecEnable deprecated
Used to set IPSEC enable/disable. at place of this value use RcIpConfEntry for IPV4 and use RcIpv6InterfaceEntry for IPV6. This field changed to deprecated
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.10.1.1.113
rcPortShutdownReason
The port shutdown can happen due to many reason. It indicates the reason for the port state change.
columnEnumeration.1.3.6.1.4.1.2272.1.4.10.1.1.114
rcPortMdixMode
Defines the MDI crossover (MDIX) modes for the port
columnEnumeration.1.3.6.1.4.1.2272.1.4.10.1.1.115
rcPortFlexUniEnable
Used to set Flex UNI enable/disable on port
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.10.1.1.116
rcPortBpduGuardTimerCount
The remaining time the port will be disabled due to a BPDU received when BPDU guard is enabled.
columnseconds SNMPv2-SMIInteger32.1.3.6.1.4.1.2272.1.4.10.1.1.117
rcPortBpduGuardTimeout
The time the port will be disabled when a BPDU is received when BPDU Guard is enabled.
columnseconds Integer32.1.3.6.1.4.1.2272.1.4.10.1.1.118
rcPortBpduGuardAdminEnabled
Used to enable/disable BPDU guard.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.10.1.1.119
rcPortAdminDuplex
Indicates the port duplex type
columnEnumeration.1.3.6.1.4.1.2272.1.4.10.1.1.12
rcPortLicenseControlStatus
This object show the license conrol status of a port. It is only applicable to a port which reuqires PORT license file to be adminstratively enabled (ifAdminStatus). …
columnEnumeration.1.3.6.1.4.1.2272.1.4.10.1.1.120
rcPortTxFlowControl
Used to enable/disable Tx flow control.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.10.1.1.121
rcPortTxFlowControlOperState
Used to indicate the Tx flow control operational state.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.10.1.1.122
rcPortCarrierDelayEnable
Used to enable/disable carrier delay feature on this port.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.10.1.1.123
rcPortCarrierDelayInterval
Used to configure the carrier delay interval in milliseconds on this port.
columnmilliseconds Integer32.1.3.6.1.4.1.2272.1.4.10.1.1.124
rcPortForwardErrorCorrection
Forward error correction
columnEnumeration.1.3.6.1.4.1.2272.1.4.10.1.1.125
rcPortForwardErrorCorrectionApplicability
Object to inidcate the valid of object rcPortForwardErrorCorrection is applicable to this interface or not
columnEnumeration.1.3.6.1.4.1.2272.1.4.10.1.1.126
rcPortMacsecMKAProfileName
Associate the port to the MACSec mka profile
columnOctetString.1.3.6.1.4.1.2272.1.4.10.1.1.127
rcPortOperAutoNegotiate
Indicate the operational state of auto negotiation.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.10.1.1.128
rcPortOperForwardErrorCorrection
Indicate the operation value of Forward error correction. cl91 - when FEC is applicable, port is up and negotiated/admin config to CLAUSE91. cl108 - when FEC is applicable…
columnEnumeration.1.3.6.1.4.1.2272.1.4.10.1.1.129
rcPortOperDuplex
Indicate this port's current duplex value.
columnEnumeration.1.3.6.1.4.1.2272.1.4.10.1.1.13
rcPortAutoSense
Set the operation value of AutoSense configuration on port. disable - AutoSense is disabled. All configuration done by AutoS…
columnEnumeration.1.3.6.1.4.1.2272.1.4.10.1.1.130
rcPortAutoSenseKeepAutoConfig
When set to true, all port configuration made by ZTF will be kept if AutoSense is disabled on port.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.10.1.1.131
rcPortCustomAutoNegAdOrigin
Indicates how the Custom Auto Negotiation Advertisements were configured. Supported values: config - set by user radius - set by radius atribute
columnBits.1.3.6.1.4.1.2272.1.4.10.1.1.132
rcPortBpduGuardOrigin
Indicates how bpdu guard was configured. Supported values: config - set by user radius - set by radius atribute
columnBits.1.3.6.1.4.1.2272.1.4.10.1.1.133
rcPortAutoSenseState
The state of the auto-sense port, when auto-sense is enabled
columnEnumeration.1.3.6.1.4.1.2272.1.4.10.1.1.134
rcPortAdminSpeed
Indicate this port's speed.
columnEnumeration.1.3.6.1.4.1.2272.1.4.10.1.1.14
rcPortOperSpeed
Indicate this port's current speed value.
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.2272.1.4.10.1.1.15
rcPortMltId
Indicate which multi-link trunk (MLT) this port is assigned to. If this port is not associated with any MLT, this value will be set to zero(0).
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.2272.1.4.10.1.1.16
rcPortLocked
Indicate whether this port is locked.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.10.1.1.17
rcPortAutoNegotiationSupported
Indicate whether this port can support auto-negotiation.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.10.1.1.18
rcPortSingleRoutablePort
Indicate whether this port is a single routable port. If this value is true, the port functions like a traditional router port.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.10.1.1.19
rcPortType
Port type
columnEnumeration.1.3.6.1.4.1.2272.1.4.10.1.1.2
rcPortUnknownMacDiscard
If rcUnknownMacDiscard is set to True, then a packet with an unknown source MAC address is dropped on that port, and other ports then will discard any packets with this MAC addres…
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.10.1.1.20
rcPortNumStateTransition
# state transitions.
columnSNMPv2-SMICounter32.1.3.6.1.4.1.2272.1.4.10.1.1.21
rcPortUserPriority deprecated
User priority level.
columnEnumeration.1.3.6.1.4.1.2272.1.4.10.1.1.22
rcPortAllowOversizeFrame deprecated
Used to specify whether over-size frames should be processed or dropped.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.10.1.1.23
rcPortConnectorType
Type of connector installed on this port.
columnEnumeration.1.3.6.1.4.1.2272.1.4.10.1.1.3
rcPortQosLevel
Used to specify the Qos level packets, carried on this port, should be processed with.
columnEnumeration.1.3.6.1.4.1.2272.1.4.10.1.1.30
rcPortDiffServEnable
Used to enable/disable the Differentiated Service feature on this port.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.10.1.1.31
rcPortDiffServType
Used to specify the Differentiated Service type for this port.
columnEnumeration.1.3.6.1.4.1.2272.1.4.10.1.1.32
rcPortDiffServIeee8021POverrideEnable deprecated
Used to enable/disable the Differentiated Service IEEE 802.1P over-ride feature.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.10.1.1.33
rcPortVendorDescr
Used to show the name of the vendor of this port's connector. Only applicable to ports on a GBIC cards.
columnOctetString.1.3.6.1.4.1.2272.1.4.10.1.1.34
rcPortName
This port's name.
columnOctetString.1.3.6.1.4.1.2272.1.4.10.1.1.35
rcPortOctapidId deprecated
The octapid id of the mirrored port.
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.2272.1.4.10.1.1.36
rcPortWan
Indicatie this port's current WAN/LAN mode. Valid for 10 GE only
columnEnumeration.1.3.6.1.4.1.2272.1.4.10.1.1.37
rcPortTransport
Indicatie this port's current tranport layer. Valid for 10 GE only
columnEnumeration.1.3.6.1.4.1.2272.1.4.10.1.1.38
rcPortMultimediaFilterEnable
Used to enable/disable the Telephony device selected on this port
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.10.1.1.39
rcPortPerformRouting deprecated
Indicate whether this port should perform routing
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.10.1.1.4
rcPortMultimediaDevSelection
Used to set/get the selected Multimedia & Telephony Devices on this port. The String is the name of the device in the rcIpFilterMediaDevTable
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.2272.1.4.10.1.1.40
rcPortServiceType
Indicates the port functionality. 12uni is used to configure the port to be part of Martini service, tls is used to configure the port to be part of Any2Any VPN service and ip is …
columnEnumeration.1.3.6.1.4.1.2272.1.4.10.1.1.41
rcPortMode
The port mode for l2uni service type.If the port is configured for l2uni service type, then the mode can be transparent or switched.
columnEnumeration.1.3.6.1.4.1.2272.1.4.10.1.1.42
rcPortAdminRouting
Indicate whether the port is routable.
columnRAPID-CITYEnableValue.1.3.6.1.4.1.2272.1.4.10.1.1.43
rcPortOperRouting
The status of the port whether is routable.
columnRAPID-CITYEnableValue.1.3.6.1.4.1.2272.1.4.10.1.1.44
rcPortPid
The pid of the mirrored port.
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.2272.1.4.10.1.1.45
rcPortIeee8021POverrideEnable
Used to enable/disable IEEE 802.1P override. If it is enabled, 802.1p vlaue from a tagged frame may not honor.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.10.1.1.46
rcPortShaperEnable
Used to enable/disable shaper on the port.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.10.1.1.47
rcPortShaperMaxRate
Shaping rate in mega bits per second. Note that actual shaping rate might be different from the configured rate due to the rate granularity of the shaper.
columnInteger32.1.3.6.1.4.1.2272.1.4.10.1.1.48
rcPortShaperBurstSize
Burst size in kilo bytes per second. Note that actual burst size might be different from the configured size due to the granularity of the shaper.
columnInteger32.1.3.6.1.4.1.2272.1.4.10.1.1.49
rcPortHighPriority deprecated
Indicate whether this port should be treated with high priority
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.10.1.1.5
rcPortCpLimitShutDown
A TRUE value indicates if CP Limit shut down the interface.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.10.1.1.50
rcPortHighSecureEnable
Enable/Disable high secure.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.10.1.1.51
rcPortTlsPriorityOverride
Enable/Disable tls port priority override feature.
columnRAPID-CITYEnableValue.1.3.6.1.4.1.2272.1.4.10.1.1.52
rcPortVctAbility
If this object is TRUE, then the specified port is hardware-capable of doing the VCT test, if the rcPortAdminStatus is also true. If this object is FALSE, then the hardware cannot…
columnEnumeration.1.3.6.1.4.1.2272.1.4.10.1.1.53
rcPortVctAdminStatus
Admin status for port VCT test. If this object is set to TRUE, then the VCT test can be performed. If it is set to FALSE, then the test cannot be performed, even if the port hardw…
columnRAPID-CITYEnableValue.1.3.6.1.4.1.2272.1.4.10.1.1.54
rcPortMrouteStrLimit
maximum number of multicast streams that are allowed to ingress to CPU through this port.
columnInteger32.1.3.6.1.4.1.2272.1.4.10.1.1.55
rcPortMrouteStrTimerCheck
sampling period to check number of multicast streams that has ingressed CPU through this port.
columnInteger32.1.3.6.1.4.1.2272.1.4.10.1.1.56
rcPortMrouteStrLimitEnable
enable or disable mroute stream limit on port.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.10.1.1.57
rcPortUpdateDynamicMacQosLevel
It is used to indicate whether to update qos level for dynamic learned mac add resses associated with a port-based vlan when port qos level changes. If it is set to TRUE, qos lev…
columnRAPID-CITYEnableValue.1.3.6.1.4.1.2272.1.4.10.1.1.58
rcPortVplsDualHoming
The VPLS dual homing is for VPLS service type only. It can be disable, firstNNI or secondNNI.
columnEnumeration.1.3.6.1.4.1.2272.1.4.10.1.1.59
rcPortAction
Port related actions.
columnEnumeration.1.3.6.1.4.1.2272.1.4.10.1.1.6
rcPortVplsMgmtVlan
Management Vlan is configured on this port
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.10.1.1.60
rcPortTlsManagedBySp
True/False tls devices on port Managed By Service Provider.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.10.1.1.61
rcPortAutoNegAd
This object is used to specify the port speed and duplex abilities to be advertised during link negotiation. bit 0 - 10 half duplex advertised bit 1 - 10 full duple…
columnBits.1.3.6.1.4.1.2272.1.4.10.1.1.62
rcPortAutoNegAdCapability
This object indicates the port speed and duplex capabilities that hardware can actually support on a port, and which may be advertised by the port using auto-negotiation. Bit 7 te…
columnBits.1.3.6.1.4.1.2272.1.4.10.1.1.63
rcPortAutoRecoverPort
enable or disable auto recovery of port from action taken by cp-limit, link flap or loop detect features
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.10.1.1.64
rcPortExtCplimitConf
Indicates the port configuration for extended CP-LIMIT
columnEnumeration.1.3.6.1.4.1.2272.1.4.10.1.1.65
rcPortExtCplimitUtilRate
Threshold for Ingress traffic utilization rate of the port for extended CP-LIMIT
columnInteger32.1.3.6.1.4.1.2272.1.4.10.1.1.66
rcPortEgressRateLimit
Egress Rate Limit. 0 means disabled.
columnInteger32.1.3.6.1.4.1.2272.1.4.10.1.1.67
rcPortEgressRateLimitState
Used to enable/disable shape/egress-rate-limit functionality.
columnRAPID-CITYEnableValue.1.3.6.1.4.1.2272.1.4.10.1.1.68
rcPortBpduFilteringTimerCount obsolete
The remaining time the port will be disabled due to a BPDU received when BPDU filtering is enabled.
columnInteger32.1.3.6.1.4.1.2272.1.4.10.1.1.69
rcPortResult
Result from the last Vlan action.
columnEnumeration.1.3.6.1.4.1.2272.1.4.10.1.1.7
rcPortBpduFilteringTimeout obsolete
The time the port will be disabled when a BPDU is received when BPDU filtering is enabled.
columnInteger32.1.3.6.1.4.1.2272.1.4.10.1.1.70
rcPortBpduFilteringAdminEnabled obsolete
Used to enable/disable BPDU filtering.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.10.1.1.71
rcPortBpduFilteringOperEnabled obsolete
Indicates whether BPDU filtering is actually enabled or disabled.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.10.1.1.72
rcPortQinqEtherType
The qinq ether type value. It is hex value. It should be displayed and input as Hex value. It is only be used when port is associated with QnQ service UNI. Otherwise, it would be …
columnInteger32.1.3.6.1.4.1.2272.1.4.10.1.1.73
rcPortTrustDscp
Used to enable/disable the trusted DSCP feature. If enabled, the internal qos-level and 802.1p value are derived from the received packet's DSCP value. This MIB object is applica…
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.10.1.1.74
rcPortCpLimitEnable
Used to enable/disable the control packet rate limit. Specifies whether or not rate limiting is currently in operation for multicast and broadcast packets for the specified port.
columnRAPID-CITYEnableValue.1.3.6.1.4.1.2272.1.4.10.1.1.75
rcPortCpMulticastLimit
Used to limit Multicast traffic on the specified port. Sets the limit in packets per second.
columnInteger32.1.3.6.1.4.1.2272.1.4.10.1.1.76
rcPortCpBroadcastLimit
Used to limit Broadcast traffic on the specified port. Sets the limit in packets per second.
columnInteger32.1.3.6.1.4.1.2272.1.4.10.1.1.77
rcPortSmartAutoNegotiate
This object indicates whether 'smart' autonegotiation is enabled on a port (smart autonegotiation indicates that the port can sense whether its partner has autonegotiation enabled…
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.10.1.1.78
rcPortMepList
List of Meps assigned to this entry. A mep is consist of <md>.<ma>.<mep_id>. Domain Name, Association and Mep Id is separated by '.' A list of mep is consist of <md1>.<ma1>.<mepid…
columnOctetString.1.3.6.1.4.1.2272.1.4.10.1.1.79
rcPortPrimaryConnector
For ports configured with redundant connectors, this value is used to indicate which connector should be used as the 'active' connector on this port the next time the port is plac…
columnEnumeration.1.3.6.1.4.1.2272.1.4.10.1.1.8
rcPortNumOfMep
Used to indicate the number of Meps is assigned to this entry
columnInteger32.1.3.6.1.4.1.2272.1.4.10.1.1.80
rcPortAdacStatus
If enabled, the Nortel IP phones connected to the port will be configured in the voice VLAN.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.10.1.1.81
rcPortPvid
A port Vlan Id associates with ESM and RModule port for OEL2/MIM traffic
columnInteger32.1.3.6.1.4.1.2272.1.4.10.1.1.82
rcPortTdp
This attribute allows to Enable/Disable Transparent Domain Protocol at the port level on the ESM and Power Ranger Card. For the TDP packet to go out on the port, topology should b…
columnRAPID-CITYEnableValue.1.3.6.1.4.1.2272.1.4.10.1.1.83
rcPortClockSource
Indicates this port's current WAN clock source. Valid for 10 GE WAN only
columnEnumeration.1.3.6.1.4.1.2272.1.4.10.1.1.84
rcPortIngressRateLimit
Limits the amount of traffic from this Ingress port.
columnInteger32.1.3.6.1.4.1.2272.1.4.10.1.1.85
rcPortIngressRateLimitState
Used to enable/disable police/ingress-rate-limit functionality.
columnRAPID-CITYEnableValue.1.3.6.1.4.1.2272.1.4.10.1.1.86
rcPortVrfIdList
The set of VRF ids to which this port belongs.
columnOctetString.1.3.6.1.4.1.2272.1.4.10.1.1.87
rcPortCfmVid
CFM default port vid
columnInteger32.1.3.6.1.4.1.2272.1.4.10.1.1.88
rcPortUserLabel1
User provided field. Used to give extra management information/data
columnOctetString.1.3.6.1.4.1.2272.1.4.10.1.1.89
rcPortActiveConnector
For ports configured with redundant connectors, this value is used to indicate which connector is currently the active one. Only one connector can be active an anytime.
columnEnumeration.1.3.6.1.4.1.2272.1.4.10.1.1.9
rcPortUserLabel2
User provided additional field. Used to give extra management information/data
columnOctetString.1.3.6.1.4.1.2272.1.4.10.1.1.90
rcPortClearCfmStats
To clear the port counter
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.2272.1.4.10.1.1.91
rcPortInterfaceType
This value indicates whether a port is of type <normal/si lent/uni>. A port can be included in any EVPN service only if this attribute is set to uni. If the port is not part of an…
columnEnumeration.1.3.6.1.4.1.2272.1.4.10.1.1.92
rcPortCfmControlMep
MEP assigned for CFM Control. A mep consists of <md>.<ma>.<mep_id>. Domain Name, Association and Mep Id is separated by '.'
columnOctetString.1.3.6.1.4.1.2272.1.4.10.1.1.93
rcPortMtu
Port Mtu
columnInteger32.1.3.6.1.4.1.2272.1.4.10.1.1.94
rcPortMtuState
Used to enable/disable Port Mtu functionality.
columnRAPID-CITYEnableValue.1.3.6.1.4.1.2272.1.4.10.1.1.95
rcPortVrfNameList
The set of VRF names to which this port belongs.
columnOctetString.1.3.6.1.4.1.2272.1.4.10.1.1.96
rcPortBrouterVrfName
Gives the VRF Name for this Brouter port.
columnOctetString.1.3.6.1.4.1.2272.1.4.10.1.1.98
rcPortVrfCount
The total number of VRFs this port is associated to.
columnSNMPv2-SMICounter32.1.3.6.1.4.1.2272.1.4.10.1.1.99