rcPortAutoNegAd
RC-PORT-MIB ·
.1.3.6.1.4.1.2272.1.4.10.1.1.62
Object
column
r/w
Bits
This object is used to specify the port speed
and duplex abilities to be advertised during
link negotiation.
bit 0 - 10 half duplex advertised
bit 1 - 10 full duplex advertised
bit 2 - 100 half duplex advertised
bit 3 - 100 full duplex advertised
bit 4 - 1000 half duplex advertised
bit 5 - 1000 full duplex advertised
bit 6 - Mac PAUSE frame support advertised
bit 7 - Asymmetric PAUSE frame support advertised
bit 8 - No advertisements
bit 9 - 10G full duplex advertisement
bit 10 - Set advertise to default setting based on the
hardware capability.
The abilities specified in this object are only used
when auto-negotiation is enabled on the port. If all
bits in this object are disabled, and auto-negotiation
is enabled on the port, then the physical link process
on the port will be disabled (if hardware supports
this ability).
Any change in the value of this bit map will force the
PHY to restart the auto-negotiation process. This will
have the same effect as physically unplugging and
reattaching the cable plant attached to this port.
The capabilities being advertised are either all the
capabilities supported by the hardware or the user-
configured capabilities which is a subset of all the
capability supported by hardware.
The default value for this object will be all the
capabilities supported by the hardware. Bit 10, default
allowed user to set advertise to default. 'default' will take
precedence if 'default' bit is combined with other bits.
Note that bit 6 and bit 7 are currently not supported
in ERS8600.
Context
- MIB
- RC-PORT-MIB
- OID
.1.3.6.1.4.1.2272.1.4.10.1.1.62- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- rcPortEntry
- Table
- rcPortTable
- Siblings
- 127
Syntax
Bits
Values & Constraints
Enumerated Values
0 | advertise10Half |
1 | advertise10Full |
2 | advertise100Half |
3 | advertise100Full |
4 | advertise1000Half |
5 | advertise1000Full |
6 | advertiseMacPause |
7 | advertiseAsymPause |
8 | advertiseNone |
9 | advertise10000Full |
10 | default |
11 | advertise2500Full |
12 | advertise5000Full |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| rcPortIndex An index value that uniquely identifies a port.
This value is similar to ifIndex in MIB2. | column | IF-MIBInterfaceIndex | .1.3.6.1.4.1.2272.1.4.10.1.1.1 |
| rcPortBackupConnectorStatus Indicate the status of the link attached to the
back-up (non-active) connector. | column | Enumeration | .1.3.6.1.4.1.2272.1.4.10.1.1.10 |
| rcPortCtrlPktDropLimitEnable Used to enable/disable Control Packets Drop
Rate Limiter functionality. | column | RAPID-CITYEnableValue | .1.3.6.1.4.1.2272.1.4.10.1.1.100 |
| rcPortCtrlPktDropLimit Indicates the Control Packet drop rate limit
value | column | Integer32 | .1.3.6.1.4.1.2272.1.4.10.1.1.101 |
| rcPortCtrlPktShutdownLimitEnable Used to enable/disable Control Packets
Shutdown Rate Limiter functionality. | column | RAPID-CITYEnableValue | .1.3.6.1.4.1.2272.1.4.10.1.1.102 |
| rcPortCtrlPktShutdownLimit Indicates the Control Packet shutdown rate
Limit value | column | Integer32 | .1.3.6.1.4.1.2272.1.4.10.1.1.103 |
| rcPortCtrlPktShutdownRtExceeded Indicates if the Shutdown rate has been exceeded
on the port | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.10.1.1.104 |
| rcPortCtrlPktDropRtExceeded Indicates if the Drop rate has been exceeded
on the port | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.10.1.1.105 |
| rcPortDhcpOption82SubscriberId This object contains the DHCP option 82 subscriber ID string to
be used in sub-option 6. If the value is an empty string, then
sub-option 6 is not included in option 82 | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.2272.1.4.10.1.1.106 |
| rcPortServiceCardType Port Hardware type, which includes PowerRanger,
ESM port and other | column | Enumeration | .1.3.6.1.4.1.2272.1.4.10.1.1.107 |
| rcPortIngressRatePeak Peak rate limit for this port. 0 means disable. | column | Integer32 | .1.3.6.1.4.1.2272.1.4.10.1.1.108 |
| rcPortIngressRateSvc Service rate limit for this port. 0 means disable. | column | Integer32 | .1.3.6.1.4.1.2272.1.4.10.1.1.109 |
| rcPortAutoNegotiate Indicate whether this port enabled for auto
negotiations or not. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.10.1.1.11 |
| rcPortCpLimitPktRate Used to limit Control packets on the
port to qos-levels 6 and 7.
Sets the limit in packets per second. | column | Integer32 | .1.3.6.1.4.1.2272.1.4.10.1.1.110 |
| rcPortCpLimitShutDownEnable Used to indicate if the port should be shutdown
when the CpLimitPktRate is exceeded. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.10.1.1.111 |
| rcPortRmonEnable Used to set Remote Monitoring enable/disable | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.10.1.1.112 |
| rcPortIpsecEnable deprecated Used to set IPSEC enable/disable.
at place of this value use RcIpConfEntry for IPV4
and use RcIpv6InterfaceEntry for IPV6. This field
changed to deprecated | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.10.1.1.113 |
| rcPortShutdownReason The port shutdown can happen due to many reason.
It indicates the reason for the port state change. | column | Enumeration | .1.3.6.1.4.1.2272.1.4.10.1.1.114 |
| rcPortMdixMode Defines the MDI crossover (MDIX) modes for the port | column | Enumeration | .1.3.6.1.4.1.2272.1.4.10.1.1.115 |
| rcPortFlexUniEnable Used to set Flex UNI
enable/disable on port | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.10.1.1.116 |
| rcPortBpduGuardTimerCount The remaining time the port will be disabled due
to a BPDU received when BPDU guard is enabled. | column | seconds SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2272.1.4.10.1.1.117 |
| rcPortBpduGuardTimeout The time the port will be disabled when a BPDU is
received when BPDU Guard is enabled. | column | seconds Integer32 | .1.3.6.1.4.1.2272.1.4.10.1.1.118 |
| rcPortBpduGuardAdminEnabled Used to enable/disable BPDU guard. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.10.1.1.119 |
| rcPortAdminDuplex Indicates the port duplex type | column | Enumeration | .1.3.6.1.4.1.2272.1.4.10.1.1.12 |
| rcPortLicenseControlStatus This object show the license conrol status of a port.
It is only applicable to a port which reuqires PORT
license file to be adminstratively enabled (ifAdminStatus).
… | column | Enumeration | .1.3.6.1.4.1.2272.1.4.10.1.1.120 |
| rcPortTxFlowControl Used to enable/disable Tx flow control. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.10.1.1.121 |
| rcPortTxFlowControlOperState Used to indicate the Tx flow control operational state. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.10.1.1.122 |
| rcPortCarrierDelayEnable Used to enable/disable carrier delay feature
on this port. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.10.1.1.123 |
| rcPortCarrierDelayInterval Used to configure the carrier delay interval
in milliseconds on this port. | column | milliseconds Integer32 | .1.3.6.1.4.1.2272.1.4.10.1.1.124 |
| rcPortForwardErrorCorrection Forward error correction | column | Enumeration | .1.3.6.1.4.1.2272.1.4.10.1.1.125 |
| rcPortForwardErrorCorrectionApplicability Object to inidcate the valid of object
rcPortForwardErrorCorrection is applicable to this
interface or not | column | Enumeration | .1.3.6.1.4.1.2272.1.4.10.1.1.126 |
| rcPortMacsecMKAProfileName Associate the port to the MACSec mka profile | column | OctetString | .1.3.6.1.4.1.2272.1.4.10.1.1.127 |
| rcPortOperAutoNegotiate Indicate the operational state of auto negotiation. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.10.1.1.128 |
| rcPortOperForwardErrorCorrection Indicate the operation value of Forward error correction.
cl91 - when FEC is applicable, port is up and
negotiated/admin config to CLAUSE91.
cl108 - when FEC is applicable… | column | Enumeration | .1.3.6.1.4.1.2272.1.4.10.1.1.129 |
| rcPortOperDuplex Indicate this port's current duplex value. | column | Enumeration | .1.3.6.1.4.1.2272.1.4.10.1.1.13 |
| rcPortAutoSense Set the operation value of AutoSense configuration on port.
disable - AutoSense is disabled. All configuration done
by AutoS… | column | Enumeration | .1.3.6.1.4.1.2272.1.4.10.1.1.130 |
| rcPortAutoSenseKeepAutoConfig When set to true, all port configuration made by ZTF will be
kept if AutoSense is disabled on port. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.10.1.1.131 |
| rcPortCustomAutoNegAdOrigin Indicates how the Custom Auto Negotiation Advertisements were configured.
Supported values:
config - set by user
radius - set by radius atribute | column | Bits | .1.3.6.1.4.1.2272.1.4.10.1.1.132 |
| rcPortBpduGuardOrigin Indicates how bpdu guard was configured.
Supported values:
config - set by user
radius - set by radius atribute | column | Bits | .1.3.6.1.4.1.2272.1.4.10.1.1.133 |
| rcPortAutoSenseState The state of the auto-sense port, when auto-sense is enabled | column | Enumeration | .1.3.6.1.4.1.2272.1.4.10.1.1.134 |
| rcPortAdminSpeed Indicate this port's speed. | column | Enumeration | .1.3.6.1.4.1.2272.1.4.10.1.1.14 |
| rcPortOperSpeed Indicate this port's current speed value. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2272.1.4.10.1.1.15 |
| rcPortMltId Indicate which multi-link trunk (MLT) this port
is assigned to. If this port is not associated
with any MLT, this value will be set to zero(0). | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2272.1.4.10.1.1.16 |
| rcPortLocked Indicate whether this port is locked. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.10.1.1.17 |
| rcPortAutoNegotiationSupported Indicate whether this port can support
auto-negotiation. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.10.1.1.18 |
| rcPortSingleRoutablePort Indicate whether this port is a single routable
port. If this value is true, the port functions
like a traditional router port. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.10.1.1.19 |
| rcPortType Port type | column | Enumeration | .1.3.6.1.4.1.2272.1.4.10.1.1.2 |
| rcPortUnknownMacDiscard If rcUnknownMacDiscard is set to True,
then a packet with an unknown source MAC address
is dropped on that port, and other ports then
will discard any packets with this MAC addres… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.10.1.1.20 |
| rcPortNumStateTransition # state transitions. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.2272.1.4.10.1.1.21 |
| rcPortUserPriority deprecated User priority level. | column | Enumeration | .1.3.6.1.4.1.2272.1.4.10.1.1.22 |
| rcPortAllowOversizeFrame deprecated Used to specify whether over-size frames should be
processed or dropped. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.10.1.1.23 |
| rcPortConnectorType Type of connector installed on this port. | column | Enumeration | .1.3.6.1.4.1.2272.1.4.10.1.1.3 |
| rcPortQosLevel Used to specify the Qos level packets, carried on this
port, should be processed with. | column | Enumeration | .1.3.6.1.4.1.2272.1.4.10.1.1.30 |
| rcPortDiffServEnable Used to enable/disable the Differentiated Service
feature on this port. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.10.1.1.31 |
| rcPortDiffServType Used to specify the Differentiated Service type
for this port. | column | Enumeration | .1.3.6.1.4.1.2272.1.4.10.1.1.32 |
| rcPortDiffServIeee8021POverrideEnable deprecated Used to enable/disable the Differentiated Service
IEEE 802.1P over-ride feature. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.10.1.1.33 |
| rcPortVendorDescr Used to show the name of the vendor of this port's
connector. Only applicable to ports on a GBIC cards. | column | OctetString | .1.3.6.1.4.1.2272.1.4.10.1.1.34 |
| rcPortName This port's name. | column | OctetString | .1.3.6.1.4.1.2272.1.4.10.1.1.35 |
| rcPortOctapidId deprecated The octapid id of the mirrored port. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2272.1.4.10.1.1.36 |
| rcPortWan Indicatie this port's current WAN/LAN mode. Valid for 10 GE only | column | Enumeration | .1.3.6.1.4.1.2272.1.4.10.1.1.37 |
| rcPortTransport Indicatie this port's current tranport layer. Valid for 10 GE only | column | Enumeration | .1.3.6.1.4.1.2272.1.4.10.1.1.38 |
| rcPortMultimediaFilterEnable Used to enable/disable the Telephony device selected on this port | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.10.1.1.39 |
| rcPortPerformRouting deprecated Indicate whether this port should perform
routing | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.10.1.1.4 |
| rcPortMultimediaDevSelection Used to set/get the selected Multimedia &
Telephony Devices on this port. The String is
the name of the device in the
rcIpFilterMediaDevTable | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.2272.1.4.10.1.1.40 |
| rcPortServiceType Indicates the port functionality. 12uni is used to
configure the port to be part of Martini service,
tls is used to configure the port to be part of
Any2Any VPN service and ip is … | column | Enumeration | .1.3.6.1.4.1.2272.1.4.10.1.1.41 |
| rcPortMode The port mode for l2uni service type.If the port is
configured for l2uni service type, then the mode can
be transparent or switched. | column | Enumeration | .1.3.6.1.4.1.2272.1.4.10.1.1.42 |
| rcPortAdminRouting Indicate whether the port is routable. | column | RAPID-CITYEnableValue | .1.3.6.1.4.1.2272.1.4.10.1.1.43 |
| rcPortOperRouting The status of the port whether is routable. | column | RAPID-CITYEnableValue | .1.3.6.1.4.1.2272.1.4.10.1.1.44 |
| rcPortPid The pid of the mirrored port. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2272.1.4.10.1.1.45 |
| rcPortIeee8021POverrideEnable Used to enable/disable IEEE 802.1P override.
If it is enabled, 802.1p vlaue from a tagged
frame may not honor. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.10.1.1.46 |
| rcPortShaperEnable Used to enable/disable shaper on the port. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.10.1.1.47 |
| rcPortShaperMaxRate Shaping rate in mega bits per second. Note that
actual shaping rate might be different from the
configured rate due to the rate granularity
of the shaper. | column | Integer32 | .1.3.6.1.4.1.2272.1.4.10.1.1.48 |
| rcPortShaperBurstSize Burst size in kilo bytes per second. Note
that actual burst size might be different
from the configured size due to the granularity
of the shaper. | column | Integer32 | .1.3.6.1.4.1.2272.1.4.10.1.1.49 |
| rcPortHighPriority deprecated Indicate whether this port should be treated with
high priority | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.10.1.1.5 |
| rcPortCpLimitShutDown A TRUE value indicates if CP Limit shut down
the interface. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.10.1.1.50 |
| rcPortHighSecureEnable Enable/Disable high secure. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.10.1.1.51 |
| rcPortTlsPriorityOverride Enable/Disable tls port priority override feature. | column | RAPID-CITYEnableValue | .1.3.6.1.4.1.2272.1.4.10.1.1.52 |
| rcPortVctAbility If this object is TRUE, then the specified port is
hardware-capable of doing the VCT test, if the
rcPortAdminStatus is also true. If this object is
FALSE, then the hardware cannot… | column | Enumeration | .1.3.6.1.4.1.2272.1.4.10.1.1.53 |
| rcPortVctAdminStatus Admin status for port VCT test. If this object is
set to TRUE, then the VCT test can be performed. If
it is set to FALSE, then the test cannot be performed,
even if the port hardw… | column | RAPID-CITYEnableValue | .1.3.6.1.4.1.2272.1.4.10.1.1.54 |
| rcPortMrouteStrLimit maximum number of multicast streams that are
allowed to ingress to CPU through this port. | column | Integer32 | .1.3.6.1.4.1.2272.1.4.10.1.1.55 |
| rcPortMrouteStrTimerCheck sampling period to check number of multicast
streams that has ingressed CPU through this port. | column | Integer32 | .1.3.6.1.4.1.2272.1.4.10.1.1.56 |
| rcPortMrouteStrLimitEnable enable or disable mroute stream limit on port. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.10.1.1.57 |
| rcPortUpdateDynamicMacQosLevel It is used to indicate whether to update qos
level for dynamic learned mac add resses
associated with a port-based vlan when port qos
level changes. If it is set to TRUE, qos lev… | column | RAPID-CITYEnableValue | .1.3.6.1.4.1.2272.1.4.10.1.1.58 |
| rcPortVplsDualHoming The VPLS dual homing is for VPLS service type only.
It can be disable, firstNNI or secondNNI. | column | Enumeration | .1.3.6.1.4.1.2272.1.4.10.1.1.59 |
| rcPortAction Port related actions. | column | Enumeration | .1.3.6.1.4.1.2272.1.4.10.1.1.6 |
| rcPortVplsMgmtVlan Management Vlan is configured on this port | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.10.1.1.60 |
| rcPortTlsManagedBySp True/False tls devices on port Managed By Service Provider. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.10.1.1.61 |
| rcPortAutoNegAdCapability This object indicates the port speed and duplex
capabilities that hardware can actually support on a
port, and which may be advertised by the port
using auto-negotiation. Bit 7 te… | column | Bits | .1.3.6.1.4.1.2272.1.4.10.1.1.63 |
| rcPortAutoRecoverPort enable or disable auto recovery of port from action
taken by cp-limit, link flap or loop detect features | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.10.1.1.64 |
| rcPortExtCplimitConf Indicates the port configuration for extended CP-LIMIT | column | Enumeration | .1.3.6.1.4.1.2272.1.4.10.1.1.65 |
| rcPortExtCplimitUtilRate Threshold for Ingress traffic utilization rate of the port
for extended CP-LIMIT | column | Integer32 | .1.3.6.1.4.1.2272.1.4.10.1.1.66 |
| rcPortEgressRateLimit Egress Rate Limit. 0 means disabled. | column | Integer32 | .1.3.6.1.4.1.2272.1.4.10.1.1.67 |
| rcPortEgressRateLimitState Used to enable/disable shape/egress-rate-limit
functionality. | column | RAPID-CITYEnableValue | .1.3.6.1.4.1.2272.1.4.10.1.1.68 |
| rcPortBpduFilteringTimerCount obsolete The remaining time the port will be disabled due
to a BPDU received when BPDU filtering is enabled. | column | Integer32 | .1.3.6.1.4.1.2272.1.4.10.1.1.69 |
| rcPortResult Result from the last Vlan action. | column | Enumeration | .1.3.6.1.4.1.2272.1.4.10.1.1.7 |
| rcPortBpduFilteringTimeout obsolete The time the port will be disabled when a BPDU is
received when BPDU filtering is enabled. | column | Integer32 | .1.3.6.1.4.1.2272.1.4.10.1.1.70 |
| rcPortBpduFilteringAdminEnabled obsolete Used to enable/disable BPDU filtering. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.10.1.1.71 |
| rcPortBpduFilteringOperEnabled obsolete Indicates whether BPDU filtering is actually
enabled or disabled. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.10.1.1.72 |
| rcPortQinqEtherType The qinq ether type value. It is hex value.
It should be displayed and input as Hex value. It is
only be used when port is associated with QnQ service
UNI. Otherwise, it would be … | column | Integer32 | .1.3.6.1.4.1.2272.1.4.10.1.1.73 |
| rcPortTrustDscp Used to enable/disable the trusted DSCP feature.
If enabled, the internal qos-level and 802.1p value are derived
from the received packet's DSCP value. This MIB object is
applica… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.10.1.1.74 |
| rcPortCpLimitEnable Used to enable/disable the control packet rate limit.
Specifies whether or not rate limiting is currently in
operation for multicast and broadcast packets for the
specified port. | column | RAPID-CITYEnableValue | .1.3.6.1.4.1.2272.1.4.10.1.1.75 |
| rcPortCpMulticastLimit Used to limit Multicast traffic on the specified port. Sets
the limit in packets per second. | column | Integer32 | .1.3.6.1.4.1.2272.1.4.10.1.1.76 |
| rcPortCpBroadcastLimit Used to limit Broadcast traffic on the specified port. Sets
the limit in packets per second. | column | Integer32 | .1.3.6.1.4.1.2272.1.4.10.1.1.77 |
| rcPortSmartAutoNegotiate This object indicates whether 'smart' autonegotiation is
enabled on a port (smart autonegotiation indicates that the
port can sense whether its partner has autonegotiation
enabled… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.10.1.1.78 |
| rcPortMepList List of Meps assigned to this entry.
A mep is consist of <md>.<ma>.<mep_id>. Domain
Name, Association and Mep Id is separated by '.'
A list of mep is consist of
<md1>.<ma1>.<mepid… | column | OctetString | .1.3.6.1.4.1.2272.1.4.10.1.1.79 |
| rcPortPrimaryConnector For ports configured with redundant connectors,
this value is used to indicate which connector
should be used as the 'active' connector on this
port the next time the port is plac… | column | Enumeration | .1.3.6.1.4.1.2272.1.4.10.1.1.8 |
| rcPortNumOfMep Used to indicate the number of Meps
is assigned to this entry | column | Integer32 | .1.3.6.1.4.1.2272.1.4.10.1.1.80 |
| rcPortAdacStatus If enabled, the Nortel IP phones connected to the port will be
configured in the voice VLAN. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.10.1.1.81 |
| rcPortPvid A port Vlan Id associates with ESM and RModule
port for OEL2/MIM traffic | column | Integer32 | .1.3.6.1.4.1.2272.1.4.10.1.1.82 |
| rcPortTdp This attribute allows to Enable/Disable Transparent
Domain Protocol at the port level on the ESM and
Power Ranger Card. For the TDP packet to go out on
the port, topology should b… | column | RAPID-CITYEnableValue | .1.3.6.1.4.1.2272.1.4.10.1.1.83 |
| rcPortClockSource Indicates this port's current WAN clock source.
Valid for 10 GE WAN only | column | Enumeration | .1.3.6.1.4.1.2272.1.4.10.1.1.84 |
| rcPortIngressRateLimit Limits the amount of traffic from this Ingress port. | column | Integer32 | .1.3.6.1.4.1.2272.1.4.10.1.1.85 |
| rcPortIngressRateLimitState Used to enable/disable police/ingress-rate-limit
functionality. | column | RAPID-CITYEnableValue | .1.3.6.1.4.1.2272.1.4.10.1.1.86 |
| rcPortVrfIdList The set of VRF ids to which this port belongs. | column | OctetString | .1.3.6.1.4.1.2272.1.4.10.1.1.87 |
| rcPortCfmVid CFM default port vid | column | Integer32 | .1.3.6.1.4.1.2272.1.4.10.1.1.88 |
| rcPortUserLabel1 User provided field. Used to give extra management information/data | column | OctetString | .1.3.6.1.4.1.2272.1.4.10.1.1.89 |
| rcPortActiveConnector For ports configured with redundant connectors,
this value is used to indicate which connector
is currently the active one. Only one connector
can be active an anytime. | column | Enumeration | .1.3.6.1.4.1.2272.1.4.10.1.1.9 |
| rcPortUserLabel2 User provided additional field. Used to give extra management information/data | column | OctetString | .1.3.6.1.4.1.2272.1.4.10.1.1.90 |
| rcPortClearCfmStats To clear the port counter | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.4.10.1.1.91 |
| rcPortInterfaceType This value indicates whether a port is of type <normal/si
lent/uni>. A port can be included in any EVPN service
only if this attribute is set to uni. If the port is not
part of an… | column | Enumeration | .1.3.6.1.4.1.2272.1.4.10.1.1.92 |
| rcPortCfmControlMep MEP assigned for CFM Control.
A mep consists of <md>.<ma>.<mep_id>. Domain
Name, Association and Mep Id is separated by '.' | column | OctetString | .1.3.6.1.4.1.2272.1.4.10.1.1.93 |
| rcPortMtu Port Mtu | column | Integer32 | .1.3.6.1.4.1.2272.1.4.10.1.1.94 |
| rcPortMtuState Used to enable/disable Port Mtu
functionality. | column | RAPID-CITYEnableValue | .1.3.6.1.4.1.2272.1.4.10.1.1.95 |
| rcPortVrfNameList The set of VRF names to which this port belongs. | column | OctetString | .1.3.6.1.4.1.2272.1.4.10.1.1.96 |
| rcPortBrouterVrfId Gives the VRF Id for this Brouter port. | column | RC-VRF-MIBVrfIdentifier | .1.3.6.1.4.1.2272.1.4.10.1.1.97 |
| rcPortBrouterVrfName Gives the VRF Name for this Brouter port. | column | OctetString | .1.3.6.1.4.1.2272.1.4.10.1.1.98 |
| rcPortVrfCount The total number of VRFs this port is associated to. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.2272.1.4.10.1.1.99 |