rcSysTrapSenderTable
RAPID-CITY-VSP ·
.1.3.6.1.4.1.2272.1.1.62
Object
table
The trap sender table (0 to 25 entries). This table lists the addresses of Network Management Stations and the Source Address that should receive trap messages from this entity when an exception condition occurs.
Context
- MIB
- RAPID-CITY-VSP
- OID
.1.3.6.1.4.1.2272.1.1.62- Type
- table
- Status
- current
- Parent
- rcSystem
- Siblings
- 82
- Children
- 1
Syntax
No syntax metadata recorded.
Values & Constraints
No enumerated values or constraints recorded.
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| rcSysIpAddr This entity's IP address. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.2272.1.1.1 |
| rcSysLastChange Last management initiated configuration
change since sysUpTime. | scalar | SNMPv2-SMITimeTicks | .1.3.6.1.4.1.2272.1.1.10 |
| rcSysLicenseTrialDaysLeft This indicates days left before License Trial
Period will expire. | scalar | Unsigned32 | .1.3.6.1.4.1.2272.1.1.100 |
| rcSysLastVlanChange Last management initiated VLAN configuration
change since sysUpTime. | scalar | SNMPv2-SMITimeTicks | .1.3.6.1.4.1.2272.1.1.11 |
| rcSysTotalPower The total power for the whole chassis. | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2272.1.1.116 |
| rcSysRedundantPower Used to indicate the redundant power on the chassis.
The redundant power is per power supply unit | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2272.1.1.117 |
| rcSysAuthSuccessTrapEnable Used to enable/disable the trap send for authenticaion
success trap rcnAuthenticationSuccess. It only allow
to be set when snmpEnableAuthenTraps is enabled.
I will be set to disab… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.1.118 |
| rcSysUdpSrcByVirtualIpEnable Used to enable/disable virtual ip as udp source. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.1.119 |
| rcSysLastStatisticsReset Last management initiated statistics reset
since sysUpTime. | scalar | SNMPv2-SMITimeTicks | .1.3.6.1.4.1.2272.1.1.12 |
| rcSysBufferUtil Buffer utilization as a percentage of the
total amount of buffer space in the system.
A high value indicates congestion. | scalar | Integer32 | .1.3.6.1.4.1.2272.1.1.13 |
| rcSysBufferUtilPeak The largest buffer utilization since sysUpTime | scalar | Integer32 | .1.3.6.1.4.1.2272.1.1.14 |
| rcSysBufferUtilPeakTime Timestamp for rcSysPeakBandwidth | scalar | SNMPv2-SMITimeTicks | .1.3.6.1.4.1.2272.1.1.15 |
| rcSysNVRamSize Total Non-volatile RAM in Kbytes | scalar | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.2272.1.1.16 |
| rcSysNVRamUsed Non-volatile RAM in use in Kbytes | scalar | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.2272.1.1.17 |
| rcSysLastSaveToNVRam SysUpTime of the last time when NVRAM was
written to. This could be a save of the system
configuration or via a file transfer of a
configuration file. | scalar | SNMPv2-SMITimeTicks | .1.3.6.1.4.1.2272.1.1.18 |
| rcSysLastSaveToStandbyNVRam SysUpTime of the last time when the standby NVRAM
(on the back-up CPU board) was written to. | scalar | SNMPv2-SMITimeTicks | .1.3.6.1.4.1.2272.1.1.19 |
| rcSysNetMask This entity's subnet mask. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.2272.1.1.2 |
| rcSysCpuUtil deprecated Percentage of CPU utilization.
This object is not supported on VSP. VSP uses
rcKhiSlotCpuCurrentUtil | scalar | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.2272.1.1.20 |
| rcSysRmonMemSize Amount of RAM in bytes to allocate for RMON
to use when rcSysRmonEnable is TRUE. | scalar | Integer32 | .1.3.6.1.4.1.2272.1.1.22 |
| rcSysRmonEnable Control whether the RMON feature should be
enabled.
To enable the RMON feature, set this variable to
true. The RMON agent in the device will get
started immediately… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.1.23 |
| rcSysRmonTrapOption Used to indicate whether RMON traps should be
sent to only the owner of the RMON alarm (i.e.,
the manager that created the alarm entry) or
all trap recipients in the system trap … | scalar | Enumeration | .1.3.6.1.4.1.2272.1.1.25 |
| rcSysSupportRouting Used to indicate whether routing is supported
in this product. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.1.26 |
| rcSysSupportWebServer Used to indicate whether WebServer is supported
in this product. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.1.27 |
| rcSysLastIpAddrChange Last management initiated IP address change
since sysUpTime. Any addition or deletion of
an IP address to a single routable port or
a VLAN is time-stamped by this variable. | scalar | SNMPv2-SMITimeTicks | .1.3.6.1.4.1.2272.1.1.28 |
| rcSysBroadcast This entity's broadcast address. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.2272.1.1.3 |
| rcSysAccessPolicyEnable Used to configure the system access policy feature.
if 'true', the rcSysAccessPolicyTable is examined to
determine which packets should be allowed or denied
access to this device. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.1.31 |
| rcSysDefaultRuntimeConfigFileName default config. | scalar | RFC1213-MIBDisplayString | .1.3.6.1.4.1.2272.1.1.32 |
| rcSysDefaultBootConfigFileName default boot config. | scalar | RFC1213-MIBDisplayString | .1.3.6.1.4.1.2272.1.1.33 |
| rcSysConfigFileName File name used in conjunction with rcSysAction.
If rcSysAction is set to 'saveRuntimeConfig' or
'saveRuntimeConfigToSlave' then this file name
will be used instead of t… | scalar | OctetString | .1.3.6.1.4.1.2272.1.1.34 |
| rcSysLastRunTimeConfigSave SysUpTime of the last time when the run time
configuration was written to. | scalar | SNMPv2-SMITimeTicks | .1.3.6.1.4.1.2272.1.1.35 |
| rcSysLastRunTimeConfigSaveToSlave SysUpTime of the last time when the run time
configuration was written to slave NVRAM. | scalar | SNMPv2-SMITimeTicks | .1.3.6.1.4.1.2272.1.1.36 |
| rcSysLastBootConfigSave SysUpTime of the last time when the boot
configuration was written to. | scalar | SNMPv2-SMITimeTicks | .1.3.6.1.4.1.2272.1.1.37 |
| rcSysLastBootConfigSaveOnSlave SysUpTime of the last time when the boot
configuration was written on the slave NVRAM. | scalar | SNMPv2-SMITimeTicks | .1.3.6.1.4.1.2272.1.1.38 |
| rcSysRmonUtilizationMethod Used to control whether RMON should use a half-duplex
or full-duplex formula to calculate port utilization.
When set to 'halfDuplex', RMON will use InOctets and
the port's speed t… | scalar | Enumeration | .1.3.6.1.4.1.2272.1.1.39 |
| rcSysOtherBufferUtil bw currently consumed | scalar | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.2272.1.1.41 |
| rcSysOtherBufferUtilPeak peak bw since reset | scalar | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.2272.1.1.42 |
| rcSysOtherBufferUtilPeakTime timestamp for rcSysPeakBw | scalar | SNMPv2-SMITimeTicks | .1.3.6.1.4.1.2272.1.1.43 |
| rcSysOtherCpuUtil % cpu utilization | scalar | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.2272.1.1.44 |
| rcSysDramSize Dram size in mega-bytes | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2272.1.1.46 |
| rcSysDramUsed Dram used in percentage | scalar | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.2272.1.1.47 |
| rcSysDramFree Dram free size in kilo-bytes | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2272.1.1.48 |
| rcSysDramMaxBlockFree Dram max block free size in kilo-bytes | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2272.1.1.49 |
| rcSysVirtualIpAddr Virtual IP is an IP address that owned and
advertised only by the master CPU. So whichever
CPU is master registers this IP address. Unlike the
management IP address, this address… | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.2272.1.1.51 |
| rcSysVirtualNetMask Net mask of the management virtual Ip address | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.2272.1.1.52 |
| rcSysReadWriteLevel The status of the read/write level | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2272.1.1.53 |
| rcSysMTUSize This is the maximum transmission size of frames that all
the ports on the chassis support. | scalar | Enumeration | .1.3.6.1.4.1.2272.1.1.55 |
| rcSysForceTrapSender This is a flag that if user wants to configured
CLIP (Circuit Less IP) as trap originator. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.1.57 |
| rcSysMrouteStrLimit enable or disable mroute stream limit in system. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.1.58 |
| rcSysAccessPolicyTable Management access policy table. This table is
used to permit or deny access to this device via
the specified source Id. | table | - | .1.3.6.1.4.1.2272.1.1.61 |
| rcSysDnsServerListTable DNS serever list table used to store the
details of the DNS server configured. | table | - | .1.3.6.1.4.1.2272.1.1.64 |
| rcSysDnsHostTable DNS Host table. | table | - | .1.3.6.1.4.1.2272.1.1.65 |
| rcSysMsgLogFrequency Used to specify the maximum frequency/count
of the occurence of the Log Message. | scalar | Integer32 | .1.3.6.1.4.1.2272.1.1.66 |
| rcSysMsgLogText A textual string containing the first four
characters of the Log Message. | scalar | OctetString | .1.3.6.1.4.1.2272.1.1.67 |
| rcSysForceIpHdrSender Flag to decide if IP header source address will
be matched with SNMP header sender networks. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.1.68 |
| rcSysVersion Software version running on device | scalar | OctetString | .1.3.6.1.4.1.2272.1.1.7 |
| rcSysDnsDomainName Default domain used for querying the DNS Server. | scalar | OctetString | .1.3.6.1.4.1.2272.1.1.70 |
| rcSysDnsServerListIpAddr DNS server's IP address | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.2272.1.1.71 |
| rcSysDnsRequestType DNS Type: Whether it was Dns Request or a Response | scalar | Enumeration | .1.3.6.1.4.1.2272.1.1.72 |
| rcSysSpanningTreeOperMode This object indicates the current spanning-tree mode
of the system.
The meaning of specific values is:
nortelStpg(1) .. The older proprietary mode which
supports multip… | scalar | Enumeration | .1.3.6.1.4.1.2272.1.1.73 |
| rcSysSpanningTreeAdminMode This object indicates the desired spanning-tree mode
of the system.
The meaning of specific values is:
nortelStpg(1) .. The older proprietary mode which
supports multip… | scalar | Enumeration | .1.3.6.1.4.1.2272.1.1.74 |
| rcSysAutoRecoverDelay Time interval in seconds after which auto-recovery
runs on ports to clear action taken by cp-limit,
link flap or loop detect | scalar | Integer32 | .1.3.6.1.4.1.2272.1.1.75 |
| rcSysMacFlapLimitTime Time limit in milliseconds for MAC flapping for
loop-detect feature | scalar | Integer32 | .1.3.6.1.4.1.2272.1.1.76 |
| rcSysMacFlapLimitCount Number of times mac flapping can happen for loop-detect
feature | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2272.1.1.77 |
| rcSysExtCplimitEnable enable or disable extended CP-LIMIT in system. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.1.78 |
| rcSysExtCplimitMinCongTime Minimum time for which System octapid should be
congested to trigger congestion algorithm for extended
CP-LIMIT in mSecs | scalar | Integer32 | .1.3.6.1.4.1.2272.1.1.79 |
| rcSysExtCplimitMaxPorts Maximum number of ports which need to be monitored
for congestion in Extended CP-LIMIT | scalar | Integer32 | .1.3.6.1.4.1.2272.1.1.80 |
| rcSysExtCplimitPortCongTime Minimum time for which ingress traffic utilization rate
of a monitored port should stay more than the allowed
limits in order to disable the port for extended
CP-LIMIT in Secs | scalar | Integer32 | .1.3.6.1.4.1.2272.1.1.81 |
| rcSysExtCplimitTrapLevel Indicates the trap level for extended CP-LIMIT | scalar | Enumeration | .1.3.6.1.4.1.2272.1.1.82 |
| rcSysExtCplimitSysOctapidCongested Indicates whether system octapid congestion detected for
extended cp-limit | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.1.83 |
| rcSysExtCplimitPortsMonitored Indicates whether ports has been shutdown due to extended
cp-limit | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.1.84 |
| rcSysExtCplimitPortsShutDown Indicates whether ports has been shutdown due to
extended Cp-limit | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2272.1.1.85 |
| rcSysActionL1 Initiate a system action for layer1 user | scalar | Enumeration | .1.3.6.1.4.1.2272.1.1.86 |
| rcSysActionL2 Initiate a system action for layer2 user | scalar | Enumeration | .1.3.6.1.4.1.2272.1.1.87 |
| rcSysActionL3 Initiate a system action for layer3 user | scalar | Enumeration | .1.3.6.1.4.1.2272.1.1.88 |
| rcSysActionRwa Initiate a system action. | scalar | Enumeration | .1.3.6.1.4.1.2272.1.1.89 |
| rcSysResult Result from the last system action. | scalar | Enumeration | .1.3.6.1.4.1.2272.1.1.9 |
| rcSysPowerUsage The current power usage for the whole chassis. | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2272.1.1.90 |
| rcSysPowerAvailable The current power available for the whole chassis. | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2272.1.1.91 |
| rcSysFrcMsgControlTable Management Force-msg Control table. This table is used to
specify the pattern for Force-msg Control | table | - | .1.3.6.1.4.1.2272.1.1.94 |
| rcSysAccPolSnmpGrpTable SNMP group list for access policy | table | - | .1.3.6.1.4.1.2272.1.1.95 |
| rcSysVirtualIpv6Addr Virtual IP is an IP address that owned and
advertised only by the master CPU. So whichever
CPU is master registers this IP address. | scalar | IPV6-TCIpv6Address | .1.3.6.1.4.1.2272.1.1.96 |
| rcSysVirtualIpv6PrefixLength The length of the virtual ipv6 addr prefix (in bits). | scalar | Integer32 | .1.3.6.1.4.1.2272.1.1.97 |
Child Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| rcSysTrapSenderEntry A trap sender table entry. | row | - | .1.3.6.1.4.1.2272.1.1.62.1 |