dsx1TxClockInstance

RAD-ds1Interface-MIB · .1.3.6.1.4.1.164.3.1.6.4.2.1.29

Object

column r/w SNMPv2-SMIUnsigned32

When dsx1TransmitClockSource is set to throughTiming(3) or
adaptive(4), this parameter specifies the instance of the
clock domain or recovered clock, respectively, that shall
be used for transmission.

Context

MIB: RAD-ds1Interface-MIB
OID: .1.3.6.1.4.1.164.3.1.6.4.2.1.29
Type: column
Access: readwrite
Status: current
Parent: dsx1XConfigEntry
Table: dsx1XConfigTable
Siblings: 29

Syntax

SNMPv2-SMIUnsigned32

Source: SNMPv2-SMIUnsigned32
Base type: Unsigned32

Values & Constraints

Type Constraints

range: 0..4294967295

Related Objects

Sibling Objects

Object	Type	Syntax	OID
dsx1IdleCode Byte pattern of the data received/transmitted in the E1T1 framer idle timeslots. Valid range: (0 - FF HEX).	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.164.3.1.6.4.2.1.1`
dsx1LineAdaptiveTimingMode Enables end to end clock synchronization. Default value - off.	column	Enumeration	`.1.3.6.1.4.1.164.3.1.6.4.2.1.10`
dsx1TxClockSource The source of Transmit Clock. 'loopTiming' indicates that the recovered receive clock is used as the transmit clock. 'localTiming' indicates that a local clock so…	column	Enumeration	`.1.3.6.1.4.1.164.3.1.6.4.2.1.11`
dsx1AisEnable Enable/ disable AIS transmit when Ethernet cable (for TDMoIP) is out (disconnected).	column	Enumeration	`.1.3.6.1.4.1.164.3.1.6.4.2.1.12`
dsx1TsEchoCancel This parameter defines for each TS whether Echo-Cancellation is on. Each bit represents one TS as follow: First octet bit'0' = TS#1, bit'7' = TS#8, .. 2nd octet bit'0' = TS#9,.., …	column	OctetString	`.1.3.6.1.4.1.164.3.1.6.4.2.1.13`
dsx1EchoCancelerModule This parameter indicates whether echo-cancellation module exists for this line.	column	Enumeration	`.1.3.6.1.4.1.164.3.1.6.4.2.1.14`
dsx1PortFunction This object determines the ATM Mode over the physical port. uni - The port will function as an ATM UNI. ces - The port will function as a CES. ima - The port will functio…	column	Enumeration	`.1.3.6.1.4.1.164.3.1.6.4.2.1.15`
dsx1PortMultiplier This object determines the data rate of each TS (Kbps units). This parameter is applicable for T1 only.	column	Enumeration	`.1.3.6.1.4.1.164.3.1.6.4.2.1.16`
dsx1LeasedLine This parameter defines whether Line mode is regular (non Leased Line mode) or transparent (Leased Line mode).	column	Enumeration	`.1.3.6.1.4.1.164.3.1.6.4.2.1.17`
dsx1CsuLoop This parameter defines where the CSU loop will be done: local - locally (by IPmux) towards the TDM device transparent - transferred to Remote Device that will send it to its …	column	Enumeration	`.1.3.6.1.4.1.164.3.1.6.4.2.1.18`
dsx1ClockSource This entry specifies the source from which the clock will be taken. Refer to device specification for source Index	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.164.3.1.6.4.2.1.19`
dsx1LineMode T1 device operation mode. Valid for T1 only.	column	Enumeration	`.1.3.6.1.4.1.164.3.1.6.4.2.1.2`
dsx1OosSignal This parameter defines the value to be sent as a signal after alarm detection: 'Space' = both A and B signaling bits are forced to '0' during out-of-service periods. …	column	Enumeration	`.1.3.6.1.4.1.164.3.1.6.4.2.1.20`
dsx1BundleNextIndex This parameter indicates the Next free Bundle Index for this DS1 port.	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.164.3.1.6.4.2.1.21`
dsx1CRC6CalcMode This object determines the CRC6 Calculation mode. jtG704 =JT-G704 = the Japanese standard ituG704=ITU-G704 = the International standard This parameter is applicable for J1 only.	column	Enumeration	`.1.3.6.1.4.1.164.3.1.6.4.2.1.22`
dsx1SendUponFail This object determines which notification will be sent to the other side upon fail of another interface. In Ipmux14 the notification is sent upon failure of the Ethernet link.	column	Enumeration	`.1.3.6.1.4.1.164.3.1.6.4.2.1.23`
dsx1InbandLoopSignal This parameter defines the signal pattern for inband loopback activation and deactivation: csu Applicable only for SF (D4) and ESF line types Defined in AT&T TR5401…	column	Enumeration	`.1.3.6.1.4.1.164.3.1.6.4.2.1.24`
dsx1InbandLoopUpCode This parameter specifies the inband signal pattern that shall cause activation of a loopback. The specified pattern is applicable only when the value of dsx1CsuLoop…	column	OctetString	`.1.3.6.1.4.1.164.3.1.6.4.2.1.25`
dsx1InbandLoopUpLength This parameter specifies the length, in bits, of the inband signal pattern that shall cause activation of a loopback. The specified pattern is applicable only when …	column	bits Unsigned32	`.1.3.6.1.4.1.164.3.1.6.4.2.1.26`
dsx1InbandLoopDownCode This parameter specifies the inband signal pattern that shall cause de-activation of a loopback. The specified pattern is applicable only when the value of dsx1CsuL…	column	OctetString	`.1.3.6.1.4.1.164.3.1.6.4.2.1.27`
dsx1InbandLoopDownLength This parameter specifies the length, in bits, of the inband signal pattern that shall cause de-activation of a loopback. The specified pattern is applicable only wh…	column	bits Unsigned32	`.1.3.6.1.4.1.164.3.1.6.4.2.1.28`
dsx1dBTxGain Transmit line Gain for T1 CSU line mode.	column	Enumeration	`.1.3.6.1.4.1.164.3.1.6.4.2.1.3`
dsx1TxPortQuality This object indicates the port clock quality.	column	Enumeration	`.1.3.6.1.4.1.164.3.1.6.4.2.1.30`
dsx1RxSensitivity Low Sensitivity is considered Short Haul while High Sensitivity is considered Long Haul. The actual values depend on the LIU. Examples: - E1: -12dB is considered Short Haul ; -43d…	column	Enumeration	`.1.3.6.1.4.1.164.3.1.6.4.2.1.4`
dsx1RestoreTime Used to change the sync. algorithms to reduce the time required for the port to return to normal operation after a RED alarm. 'sec1' = Fast, 'sec10' = TR-6211, 'immediate' = C…	column	Enumeration	`.1.3.6.1.4.1.164.3.1.6.4.2.1.5`
dsx1TcFirstSignal Trunk conditioning signal - value to be sent as a signal during the first 2.5 seconds after alarm detection. Range is 0x0..0xF. 0xFF is a NULL value. This variable is used al…	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.164.3.1.6.4.2.1.6`
dsx1TcSignal Trunk conditioning signal value after alarm detection. Range is 0x1..0xF for E1, and 0x0..0xF for T1. This variable is used also for Space Signaling Code (E1 and T1).	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.164.3.1.6.4.2.1.7`
dsx1TcPattern Trunk conditioning data pattern to be sent upon a DS0 fail. Range is 0x0..0xFF. This variable used also for Out of Service Code.	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.164.3.1.6.4.2.1.8`
dsx1Scramble Scrambling is an operation that randomizes the bits of the payload of the ATM cell by a polynom. This operation helps with the error detection mechanism of the HEC. Not applicabl…	column	Enumeration	`.1.3.6.1.4.1.164.3.1.6.4.2.1.9`