dsx1CsuLoop
RAD-ds1Interface-MIB ·
.1.3.6.1.4.1.164.3.1.6.4.2.1.18
Object
column
r/w
Enumeration
This parameter defines where the CSU loop will be done:
local - locally (by IPmux) towards the TDM device
transparent - transferred to Remote Device that will send it to its
connected TDM device.
remote - Remote Device will close the loop towards the Local Device.
Context
- MIB
- RAD-ds1Interface-MIB
- OID
.1.3.6.1.4.1.164.3.1.6.4.2.1.18- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- dsx1XConfigEntry
- Table
- dsx1XConfigTable
- Siblings
- 29
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | notApplicable |
2 | local |
3 | transparent |
4 | remote |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| dsx1IdleCode Byte pattern of the data received/transmitted in the
E1T1 framer idle timeslots.
Valid range: (0 - FF HEX). | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.1.6.4.2.1.1 |
| dsx1LineAdaptiveTimingMode Enables end to end clock synchronization.
Default value - off. | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.4.2.1.10 |
| dsx1TxClockSource The source of Transmit Clock.
'loopTiming' indicates that the recovered receive clock
is used as the transmit clock.
'localTiming' indicates that a local clock
so… | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.4.2.1.11 |
| dsx1AisEnable Enable/ disable AIS transmit when Ethernet cable (for TDMoIP) is out (disconnected). | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.4.2.1.12 |
| dsx1TsEchoCancel This parameter defines for each TS whether Echo-Cancellation is on.
Each bit represents one TS as follow:
First octet bit'0' = TS#1, bit'7' = TS#8, .. 2nd octet bit'0' = TS#9,.., … | column | OctetString | .1.3.6.1.4.1.164.3.1.6.4.2.1.13 |
| dsx1EchoCancelerModule This parameter indicates whether echo-cancellation module
exists for this line. | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.4.2.1.14 |
| dsx1PortFunction This object determines the ATM Mode over the
physical port.
uni - The port will function as an ATM UNI.
ces - The port will function as a CES.
ima - The port will functio… | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.4.2.1.15 |
| dsx1PortMultiplier This object determines the data rate of each TS
(Kbps units).
This parameter is applicable for T1 only. | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.4.2.1.16 |
| dsx1LeasedLine This parameter defines whether Line mode is regular (non Leased Line mode)
or transparent (Leased Line mode). | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.4.2.1.17 |
| dsx1ClockSource This entry specifies the source from which the clock will be taken.
Refer to device specification for source Index | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.1.6.4.2.1.19 |
| dsx1LineMode T1 device operation mode.
Valid for T1 only. | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.4.2.1.2 |
| dsx1OosSignal This parameter defines the value to be sent as a signal
after alarm detection:
'Space' = both A and B signaling bits are forced
to '0' during out-of-service periods.
… | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.4.2.1.20 |
| dsx1BundleNextIndex This parameter indicates the Next free Bundle Index for this DS1 port. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.1.6.4.2.1.21 |
| dsx1CRC6CalcMode This object determines the CRC6 Calculation mode.
jtG704 =JT-G704 = the Japanese standard
ituG704=ITU-G704 = the International standard
This parameter is applicable for J1 only. | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.4.2.1.22 |
| dsx1SendUponFail This object determines which notification will be sent to the other side
upon fail of another interface.
In Ipmux14 the notification is sent upon failure of the Ethernet link. | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.4.2.1.23 |
| dsx1InbandLoopSignal This parameter defines the signal pattern for inband loopback
activation and deactivation:
csu
Applicable only for SF (D4) and ESF line types
Defined in AT&T TR5401… | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.4.2.1.24 |
| dsx1InbandLoopUpCode This parameter specifies the inband signal pattern that shall
cause activation of a loopback.
The specified pattern is applicable only when the value of
dsx1CsuLoop… | column | OctetString | .1.3.6.1.4.1.164.3.1.6.4.2.1.25 |
| dsx1InbandLoopUpLength This parameter specifies the length, in bits, of the inband
signal pattern that shall cause activation of a loopback.
The specified pattern is applicable only when … | column | bits Unsigned32 | .1.3.6.1.4.1.164.3.1.6.4.2.1.26 |
| dsx1InbandLoopDownCode This parameter specifies the inband signal pattern that shall
cause de-activation of a loopback.
The specified pattern is applicable only when the value of
dsx1CsuL… | column | OctetString | .1.3.6.1.4.1.164.3.1.6.4.2.1.27 |
| dsx1InbandLoopDownLength This parameter specifies the length, in bits, of the inband
signal pattern that shall cause de-activation of a loopback.
The specified pattern is applicable only wh… | column | bits Unsigned32 | .1.3.6.1.4.1.164.3.1.6.4.2.1.28 |
| dsx1TxClockInstance When dsx1TransmitClockSource is set to throughTiming(3) or
adaptive(4), this parameter specifies the instance of the
clock domain or recovered clock, respectively, that shall
be u… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.164.3.1.6.4.2.1.29 |
| dsx1dBTxGain Transmit line Gain for T1 CSU line mode. | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.4.2.1.3 |
| dsx1TxPortQuality This object indicates the port clock quality. | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.4.2.1.30 |
| dsx1RxSensitivity Low Sensitivity is considered Short Haul while High Sensitivity
is considered Long Haul. The actual values depend on the LIU.
Examples:
- E1: -12dB is considered Short Haul ; -43d… | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.4.2.1.4 |
| dsx1RestoreTime Used to change the sync. algorithms to reduce the time
required for the port to return to normal operation after
a RED alarm.
'sec1' = Fast,
'sec10' = TR-6211,
'immediate' = C… | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.4.2.1.5 |
| dsx1TcFirstSignal Trunk conditioning signal - value to be sent as a signal
during the first 2.5 seconds after alarm detection.
Range is 0x0..0xF. 0xFF is a NULL value.
This variable is used al… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.1.6.4.2.1.6 |
| dsx1TcSignal Trunk conditioning signal value after alarm detection.
Range is 0x1..0xF for E1, and 0x0..0xF for T1.
This variable is used also for Space Signaling Code (E1 and T1). | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.1.6.4.2.1.7 |
| dsx1TcPattern Trunk conditioning data pattern to be sent upon a DS0 fail.
Range is 0x0..0xFF.
This variable used also for Out of Service Code. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.1.6.4.2.1.8 |
| dsx1Scramble Scrambling is an operation that randomizes the bits
of the payload of the ATM cell by a polynom.
This operation helps with the error detection mechanism
of the HEC. Not applicabl… | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.4.2.1.9 |