hdsl2ShdslIfConfIdx

RAD-RadShdsl-MIB · .1.3.6.1.4.1.164.3.1.6.12.4.1.1.1

MIB view Table view

Object

column Integer32

This object indicates the Idx of the Config being accessed.
Idx of 255 relates to the Temporary (Scratch) Config.
Write operation for products supporting Active+Temp configurations,
is allowed to Temporary configuration only.

Context

MIB: RAD-RadShdsl-MIB
OID: .1.3.6.1.4.1.164.3.1.6.12.4.1.1.1
Type: column
Access: readonly
Status: current
Parent: hdsl2ShdslIfConfEntry
Table: hdsl2ShdslIfConfTable
Siblings: 17

Syntax

Integer32

Values & Constraints

Object Constraints

range: 1-255

Related Objects

Sibling Objects

Object	Type	Syntax	OID
hdsl2ShdslTsCompactionMode This object configures how TSs will be compacted over the SHDSL Line. In both mapping cases (2),(3), only the TSs connected on the E1 line will be transferred over the SHDSL Line…	column	Enumeration	`.1.3.6.1.4.1.164.3.1.6.12.4.1.1.10`
hdsl2ShdslEocEnable This object configures whether EOC protocol is supported by the Far-End device working with this port.	column	Enumeration	`.1.3.6.1.4.1.164.3.1.6.12.4.1.1.11`
hdsl2ShdslFar1stIfNumOfTSs This object configures the number of TSs of the SHDSL line that belong to the 1st Interface of the Far-End device, where 1st means that these TSs are first on the SHDSL line. …	column	SNMPv2-SMIUnsigned32	`.1.3.6.1.4.1.164.3.1.6.12.4.1.1.12`
hdsl2ShdslFarEndDevice This object indicates the Far-End device. It is used for 2 purposes: - in order to know if EOC is used (EOC is used only when the device is any of the ASMi52 options: (4)..(7)) …	column	Enumeration	`.1.3.6.1.4.1.164.3.1.6.12.4.1.1.13`
hdsl2ShdslPwrBackoffDb This object configures the Power Backoff (in dB) of the receiver, at the associated segment endpoint. 0=Off Valid values: 0..31 .	column	dB SNMPv2-SMIInteger32	`.1.3.6.1.4.1.164.3.1.6.12.4.1.1.14`
hdsl2ShdslFarEndMuxTsa This object represents Assignment of E1 TSs to Far-End MUX Interfaces. It is relevant only when hdsl2ShdslSideIdx=nearEnd(2), when for the Near-End device, hdsl2ShdslMode=stuC(2)…	column	OctetString	`.1.3.6.1.4.1.164.3.1.6.12.4.1.1.15`
hdsl2ShdslLineProbeEnable This object enables/disables support for Line Probe of the units in an SHDSL line. When Line Probe is enabled, the system performs Line Probing to find the best possible rate. I…	column	Enumeration	`.1.3.6.1.4.1.164.3.1.6.12.4.1.1.16`
hdsl2ShdslClockMode This object enables configuration of the clock mode. (1) - 1 Plesiochronous (e.g. ASMi-52 / ASMi-54L) (2) - 2 Plesiochronous with timing reference (e.g. ASMi-54 / ASMi-54L) (3) - …	column	Enumeration	`.1.3.6.1.4.1.164.3.1.6.12.4.1.1.17`
hdsl2ShdslIfConfLinkDownReason	column	Bits	`.1.3.6.1.4.1.164.3.1.6.12.4.1.1.19`
hdsl2ShdslSideIdx This object indicates the Side of the managed object: Near-End or Far-End.	column	Enumeration	`.1.3.6.1.4.1.164.3.1.6.12.4.1.1.2`
hdsl2ShdslMaxBw Maximum BW (Bandwidth) of the Shdsl Line, in Kbps units. Respective Max No. of TSs = Max. Rate/64 This object can be Set only for a Central (xtuC) unit.	column	Enumeration	`.1.3.6.1.4.1.164.3.1.6.12.4.1.1.3`
hdsl2ShdslPwrBackoff This object configures the receiver at the associated segment endpoint to enable/disable power backoff mode. This object is similar to hdsl2ShdslMaintPowerBackOff, but per configu…	column	Enumeration	`.1.3.6.1.4.1.164.3.1.6.12.4.1.1.4`
hdsl2ShdslTxMode This object configures the Transmission Mode for the SHDSL Line. Normally, This object can be Set only for a Central (xtuC) unit.	column	Enumeration	`.1.3.6.1.4.1.164.3.1.6.12.4.1.1.5`
hdsl2ShdslAttenuationThreshold This object configures the Attentuation alarm threshold. 0=Off Valid values: 0..127 .	column	dB SNMPv2-SMIInteger32	`.1.3.6.1.4.1.164.3.1.6.12.4.1.1.6`
hdsl2ShdslSnrMarginThreshold This object configures the SNR margin alarm threshold. 0=Off Valid values: 0..15 .	column	dB SNMPv2-SMIInteger32	`.1.3.6.1.4.1.164.3.1.6.12.4.1.1.7`
hdsl2ShdslTs0OverDsl This object configures the way TS0 will be treated over the SHDSL Line. looped - looped inside transparent - sent transparently over the DSL Line. This object can be Set only for …	column	Enumeration	`.1.3.6.1.4.1.164.3.1.6.12.4.1.1.8`
hdsl2ShdslMode This object is relevant only for the Near-End device. stuC - Central stuR - Remote .	column	Enumeration	`.1.3.6.1.4.1.164.3.1.6.12.4.1.1.9`