hdsl2ShdslClockMode
RAD-RadShdsl-MIB ·
.1.3.6.1.4.1.164.3.1.6.12.4.1.1.17
Object
column
r/w
Enumeration
This object enables configuration of the clock mode. (1) - 1 Plesiochronous (e.g. ASMi-52 / ASMi-54L) (2) - 2 Plesiochronous with timing reference (e.g. ASMi-54 / ASMi-54L) (3) - 3a - Synchronous (4) - 3b - Hybrid: downstream: synchronous; upstream: plesiochronous
Context
- MIB
- RAD-RadShdsl-MIB
- OID
.1.3.6.1.4.1.164.3.1.6.12.4.1.1.17- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- hdsl2ShdslIfConfEntry
- Table
- hdsl2ShdslIfConfTable
- Siblings
- 17
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | plesiochronous1 |
2 | plesiochronousWithTimeReference2 |
3 | synchronous3a |
4 | hybrid |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| hdsl2ShdslIfConfIdx This object indicates the Idx of the Config being accessed.
Idx of 255 relates to the Temporary (Scratch) Config.
Write operation for products supporting Active+Temp configuration… | column | Integer32 | .1.3.6.1.4.1.164.3.1.6.12.4.1.1.1 |
| hdsl2ShdslTsCompactionMode This object configures how TSs will be compacted over the SHDSL Line.
In both mapping cases (2),(3), only the TSs connected on the E1 line will be
transferred over the SHDSL Line… | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.12.4.1.1.10 |
| hdsl2ShdslEocEnable This object configures whether EOC protocol is supported by the Far-End
device working with this port. | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.12.4.1.1.11 |
| hdsl2ShdslFar1stIfNumOfTSs This object configures the number of TSs of the SHDSL line
that belong to the 1st Interface of the Far-End device, where
1st means that these TSs are first on the SHDSL line.
… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.164.3.1.6.12.4.1.1.12 |
| hdsl2ShdslFarEndDevice This object indicates the Far-End device.
It is used for 2 purposes:
- in order to know if EOC is used (EOC is used only when the device
is any of the ASMi52 options: (4)..(7))
… | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.12.4.1.1.13 |
| hdsl2ShdslPwrBackoffDb This object configures the Power Backoff (in dB) of the
receiver, at the associated segment endpoint.
0=Off
Valid values: 0..31 . | column | dB SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.1.6.12.4.1.1.14 |
| hdsl2ShdslFarEndMuxTsa This object represents Assignment of E1 TSs to Far-End MUX Interfaces.
It is relevant only when hdsl2ShdslSideIdx=nearEnd(2), when for the
Near-End device, hdsl2ShdslMode=stuC(2)… | column | OctetString | .1.3.6.1.4.1.164.3.1.6.12.4.1.1.15 |
| hdsl2ShdslLineProbeEnable This object enables/disables support for Line Probe of
the units in an SHDSL line. When Line Probe is enabled, the
system performs Line Probing to find the best possible
rate. I… | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.12.4.1.1.16 |
| hdsl2ShdslIfConfLinkDownReason | column | Bits | .1.3.6.1.4.1.164.3.1.6.12.4.1.1.19 |
| hdsl2ShdslSideIdx This object indicates the Side of the managed object: Near-End
or Far-End. | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.12.4.1.1.2 |
| hdsl2ShdslMaxBw Maximum BW (Bandwidth) of the Shdsl Line, in Kbps units.
Respective Max No. of TSs = Max. Rate/64
This object can be Set only for a Central (xtuC) unit. | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.12.4.1.1.3 |
| hdsl2ShdslPwrBackoff This object configures the receiver at the associated
segment endpoint to enable/disable power backoff mode.
This object is similar to hdsl2ShdslMaintPowerBackOff, but per
configu… | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.12.4.1.1.4 |
| hdsl2ShdslTxMode This object configures the Transmission Mode for the SHDSL Line.
Normally, This object can be Set only for a Central (xtuC) unit. | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.12.4.1.1.5 |
| hdsl2ShdslAttenuationThreshold This object configures the Attentuation alarm threshold.
0=Off
Valid values: 0..127 . | column | dB SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.1.6.12.4.1.1.6 |
| hdsl2ShdslSnrMarginThreshold This object configures the SNR margin alarm threshold.
0=Off
Valid values: 0..15 . | column | dB SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.1.6.12.4.1.1.7 |
| hdsl2ShdslTs0OverDsl This object configures the way TS0 will be treated over the SHDSL Line.
looped - looped inside
transparent - sent transparently over the DSL Line.
This object can be Set only for … | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.12.4.1.1.8 |
| hdsl2ShdslMode This object is relevant only for the Near-End device.
stuC - Central
stuR - Remote . | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.12.4.1.1.9 |