sysSSelfTestResult
RAD-MIB ·
.1.3.6.1.4.1.164.3.3.1.3.15
Object
scalar
SNMPv2-SMIInteger32
The test is performed by the active Common Logic card.
The result will be a sum of 2**n according to the following
bit convention:
For DXC:
bit 0 Database 1 Checksum Error (LSB)
bit 1 Database 2 Checksum Error
bit 2 I/O Expander Error
bit 3 Counter Error
bit 4 Matrix DPR Error
bit 5 PS-A 5 Volt Error
bit 6 PS-A 12 Volt Error
bit 7 PS-B 5 Volt Error
bit 8 PS-B 12 Volt Error
bit 9 EPROM Failure
For FCD:
bit 0 I/O Expander Error (LSB)
bit 1 Counter Error
bit 2 EPROM Failure
bit 3 Illegal Sys Config
bit 4 SFIFO
bit 5 EPIC Failure (ISDN)
bit 6 XL Flash Fail -- for MSDSL interface
bit 7 XL MITEL Fail -- for MSDSL interface
bit 8 XL Framer Fail -- for MSDSL interface
bit 9 XL DSP Fail -- for MSDSL interface
For LRS52 - refer to product's spec
When a bit is ('1'), the error exists.
When NO ERROR is encountered, this object's value will be 0.
Syntax
SNMPv2-SMIInteger32
- Source
- SNMPv2-SMIInteger32
- Base type
Integer32
Values & Constraints
Type Constraints
range: -2147483648..2147483647
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| sysSDateFormat This object indicates the date and time format used for the
sysSDateAndTimeCmd and for the alarm buffer report. | scalar | Enumeration | .1.3.6.1.4.1.164.3.3.1.3.1 |
| sysSTestStatus Indicates the current test status (for all levels: system,
card, port).
This attribute will be set to:
- on(3): when there is at least one test in progress on the
system… | scalar | Enumeration | .1.3.6.1.4.1.164.3.3.1.3.10 |
| sysSSanityCheckStatus Upon completion of the Sanity Check process on the TmpCnfg
this object will be set to:
- fail(2): when there is at least one error (which is
not just a warning) encou… | scalar | Enumeration | .1.3.6.1.4.1.164.3.3.1.3.11 |
| sysSNoOfSanityCheckErr This object indicates the number of errors/warnings
discovered by the last Sanity Check process. | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.3.1.3.12 |
| sysSErrListTable A table. | table | - | .1.3.6.1.4.1.164.3.3.1.3.13 |
| sysSMaxNoOfCnfg Maximum number of configurations that can be defined and
stored in the DACS agent.
If the DACS agent has a large capacity, the maximum will be
limited to 254. | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.3.1.3.14 |
| sysSRelayState Indicates the current state of the alarm relay.
notApplicable - for agents that do not support this object. | scalar | Enumeration | .1.3.6.1.4.1.164.3.3.1.3.16 |
| sysSInvertedAlr Indicates if there is any Inverted alarm at any level of the
system (sys, card, port).
notApplicable - for agents that do not support this object. | scalar | Enumeration | .1.3.6.1.4.1.164.3.3.1.3.17 |
| sysSRdnFlipTable This table includes all the Flip events due to I/O Redundancy since
last Clear command of this table. | table | - | .1.3.6.1.4.1.164.3.3.1.3.18 |
| sysSRdnFlipTableClearCmd This command, when Set to 'on', clears the Redundancy Flip
table (sysSRdnFlipTable).
After clear is performed, the agent will turn the value to 'off'
automatically. | scalar | Enumeration | .1.3.6.1.4.1.164.3.3.1.3.19 |
| sysSDateCmd This object indicates the current date as it is known by the
agent using its own real-time clock. The format would be as
specified by the sysSDateFormat.
This parameter can be se… | scalar | OctetString | .1.3.6.1.4.1.164.3.3.1.3.2 |
| sysSRdnFlipCmd This object enables the user to send a command to the Agent, to Flip
from a current Online IO card to its Redundant card.
The value sent will be an Object Identifier of an entry… | scalar | ObjectIdentifier | .1.3.6.1.4.1.164.3.3.1.3.20 |
| sysSBusTable This table includes data and status about the internal DXC BUS. | table | - | .1.3.6.1.4.1.164.3.3.1.3.21 |
| sysSRdnCmdTable This table includes commands used for IO Redundancy. | table | - | .1.3.6.1.4.1.164.3.3.1.3.22 |
| sysSAlrAttrIndication This object indicates the status of the Alarm Attributes
for the whole device.
It is a sum of 2**(Bit-1). A Bit will be '1', when any alarm in the
device is Filtered/Masked/I… | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.3.1.3.23 |
| sysSTimeCmd This object indicates the current time as it is known by the
agent using its own real-time clock.
This parameter can be set for time synchronization between
the NMS and the Agent… | scalar | OctetString | .1.3.6.1.4.1.164.3.3.1.3.3 |
| sysSActiveCnfg This object specifies the configuration number,
that is currently active and running. | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.3.1.3.4 |
| sysSEditCnfg This object indicates the unique configuration number that
is currently loaded into the tmp working space for
manipulation and update operations. Value of 255 means no
config.… | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.3.1.3.5 |
| sysSEditBy This entry indicates which MMI application is working on
the edited config.
The editing phase starts at the first modify operation and
ends after a load operation. | scalar | Enumeration | .1.3.6.1.4.1.164.3.3.1.3.6 |
| sysSClkSrc This entry indicates the source of the system clock. | scalar | Enumeration | .1.3.6.1.4.1.164.3.3.1.3.7 |
| sysSAlrStatus Indicates the current alarm state only for system level.
This object will be :
- critical(7): when there is at least one active (ON) critical
alarm .
- major (3): w… | scalar | Enumeration | .1.3.6.1.4.1.164.3.3.1.3.8 |
| sysSAlrStatusAll Indicates the current alarm state including all levels:
system, card, port.
- critical(7): when there is at least one active (ON) critical
alarm .
- major (3): when… | scalar | Enumeration | .1.3.6.1.4.1.164.3.3.1.3.9 |