sysSRdnFlipCmd
RAD-MIB ·
.1.3.6.1.4.1.164.3.3.1.3.20
Object
scalar
r/w
ObjectIdentifier
This object enables the user to send a command to the Agent, to Flip
from a current Online IO card to its Redundant card.
The value sent will be an Object Identifier of an entry in the sysCRdnTable.
This entry defines the Redundant couple of Slots on which the Flip
is applied.
Setting this object, will cause the Agent to Flip from current Online
card to its Redundant card.
This manual flip command is applicable only for entries having
Redundancy Mode=Y Cable.
For Vmux: This command will cause flipping from Secondary or Third Link to the
Primary Link. If the active link is the primary link, the agent will flip to the
secondary link. The value sent will be the Object Identifier of the following
Table: agnCBuMlTable.
Agent will send the value 0 for Get.
Syntax
ObjectIdentifier
Values & Constraints
No enumerated values or constraints recorded.
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| sysSDateFormat This object indicates the date and time format used for the
sysSDateAndTimeCmd and for the alarm buffer report. | scalar | Enumeration | .1.3.6.1.4.1.164.3.3.1.3.1 |
| sysSTestStatus Indicates the current test status (for all levels: system,
card, port).
This attribute will be set to:
- on(3): when there is at least one test in progress on the
system… | scalar | Enumeration | .1.3.6.1.4.1.164.3.3.1.3.10 |
| sysSSanityCheckStatus Upon completion of the Sanity Check process on the TmpCnfg
this object will be set to:
- fail(2): when there is at least one error (which is
not just a warning) encou… | scalar | Enumeration | .1.3.6.1.4.1.164.3.3.1.3.11 |
| sysSNoOfSanityCheckErr This object indicates the number of errors/warnings
discovered by the last Sanity Check process. | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.3.1.3.12 |
| sysSErrListTable A table. | table | - | .1.3.6.1.4.1.164.3.3.1.3.13 |
| sysSMaxNoOfCnfg Maximum number of configurations that can be defined and
stored in the DACS agent.
If the DACS agent has a large capacity, the maximum will be
limited to 254. | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.3.1.3.14 |
| sysSSelfTestResult The test is performed by the active Common Logic card.
The result will be a sum of 2**n according to the following
bit convention:
For DXC:
bit 0 Database 1 Checksum Error (LSB)… | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.3.1.3.15 |
| sysSRelayState Indicates the current state of the alarm relay.
notApplicable - for agents that do not support this object. | scalar | Enumeration | .1.3.6.1.4.1.164.3.3.1.3.16 |
| sysSInvertedAlr Indicates if there is any Inverted alarm at any level of the
system (sys, card, port).
notApplicable - for agents that do not support this object. | scalar | Enumeration | .1.3.6.1.4.1.164.3.3.1.3.17 |
| sysSRdnFlipTable This table includes all the Flip events due to I/O Redundancy since
last Clear command of this table. | table | - | .1.3.6.1.4.1.164.3.3.1.3.18 |
| sysSRdnFlipTableClearCmd This command, when Set to 'on', clears the Redundancy Flip
table (sysSRdnFlipTable).
After clear is performed, the agent will turn the value to 'off'
automatically. | scalar | Enumeration | .1.3.6.1.4.1.164.3.3.1.3.19 |
| sysSDateCmd This object indicates the current date as it is known by the
agent using its own real-time clock. The format would be as
specified by the sysSDateFormat.
This parameter can be se… | scalar | OctetString | .1.3.6.1.4.1.164.3.3.1.3.2 |
| sysSBusTable This table includes data and status about the internal DXC BUS. | table | - | .1.3.6.1.4.1.164.3.3.1.3.21 |
| sysSRdnCmdTable This table includes commands used for IO Redundancy. | table | - | .1.3.6.1.4.1.164.3.3.1.3.22 |
| sysSAlrAttrIndication This object indicates the status of the Alarm Attributes
for the whole device.
It is a sum of 2**(Bit-1). A Bit will be '1', when any alarm in the
device is Filtered/Masked/I… | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.3.1.3.23 |
| sysSTimeCmd This object indicates the current time as it is known by the
agent using its own real-time clock.
This parameter can be set for time synchronization between
the NMS and the Agent… | scalar | OctetString | .1.3.6.1.4.1.164.3.3.1.3.3 |
| sysSActiveCnfg This object specifies the configuration number,
that is currently active and running. | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.3.1.3.4 |
| sysSEditCnfg This object indicates the unique configuration number that
is currently loaded into the tmp working space for
manipulation and update operations. Value of 255 means no
config.… | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.3.1.3.5 |
| sysSEditBy This entry indicates which MMI application is working on
the edited config.
The editing phase starts at the first modify operation and
ends after a load operation. | scalar | Enumeration | .1.3.6.1.4.1.164.3.3.1.3.6 |
| sysSClkSrc This entry indicates the source of the system clock. | scalar | Enumeration | .1.3.6.1.4.1.164.3.3.1.3.7 |
| sysSAlrStatus Indicates the current alarm state only for system level.
This object will be :
- critical(7): when there is at least one active (ON) critical
alarm .
- major (3): w… | scalar | Enumeration | .1.3.6.1.4.1.164.3.3.1.3.8 |
| sysSAlrStatusAll Indicates the current alarm state including all levels:
system, card, port.
- critical(7): when there is at least one active (ON) critical
alarm .
- major (3): when… | scalar | Enumeration | .1.3.6.1.4.1.164.3.3.1.3.9 |