prtGenTestRunningXP
RAD-MIB ·
.1.3.6.1.4.1.164.3.3.3.1.1.1.19
Object
column
OctetString
This is an Expanded object of the prtGenTestRunning object.
The prtGenTestRunning object reached its maximum, being an Integer with 31 bits.
This object indicates which tests are running currently on
the selected port (initiated by user and/or by the system).
If a specific test is currently running on the port, its
respective bit will be SET:
TEST BIT
----------- ---
localLoop 1 =LSB
remoteLoop 2
bert 3
plb 4
llb 5
txInband 6
rxInband 7
prbs 8
loop2-v54 (RLB) 9
loop3-v54 (LLB) 10
DDS DSU loop 11
DDS CSU loop 12
Tone injection 13
Tx-plb 14
Tx-llb 15
DTE loop (HSSI) 16
Local DTE loop (HSSI)17
Local Line loop (HSSI)18
Remote Line loop (HSSI)19
HDSL-Tx-Inband 20
HDSL-Rx-Inband 21
Monitor 22 (test port)
User Line Loopback 23
Network Line Loopback 24
Rem-Loop-on-Rem-Unit 25
LBBD 26
LB1 27
LB2 28
BERT-on-Rem-Unit 29
TS Remote Loop 30
LLB-on-Rem-Unit 31
Downstream-AIS 32
Upstream-AIS 33
Send-RDI 34
Test Per TS 35
e.g : If the return value is 00000003 hex ->
Bits 1 & 2 are set -> the running tests are :
local-loop
remote-loop
llb (Bit 5) - can be initiated by system only!
Context
- MIB
- RAD-MIB
- OID
.1.3.6.1.4.1.164.3.3.3.1.1.1.19- Type
- column
- Access
- readonly
- Status
- current
- Parent
- prtGenEntry
- Table
- prtGenParamTable
- Siblings
- 18
Syntax
OctetString
Values & Constraints
No enumerated values or constraints recorded.
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| prtGenPrtIdx This attribute indicates a unique number to identify a port.
The valid port number depends on the IO slot no., the
installed card type and the port type: outside/external, insi… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.3.3.1.1.1.1 |
| prtGenTestRunning This object indicates which tests are running currently on
the selected port (initiated by user and/or by the system).
If a specific test is currently running on the port, its
r… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.3.3.1.1.1.10 |
| prtGenType This object describes the type of the selected port.
idsl - applicable for external ports of HS-U cards (of DXC) when
interface is LT-1. | column | Enumeration | .1.3.6.1.4.1.164.3.3.3.1.1.1.11 |
| prtGenInterfaceType This attribute indicates a unique HW interface type of the
selected port.
Examples:
- for T1 cards: DSU, CSU
- for E1 cards: DSU, LTU
- for HS cards: v35, rs422, x21
etc... | column | OctetString | .1.3.6.1.4.1.164.3.3.3.1.1.1.12 |
| prtGenAlrClearCmd Setting this attribute to ON, will enforce a clear
operation on the port level alarms . Upon completion,
the value will automatically change to off(2).
noOp - will be used by a… | column | Enumeration | .1.3.6.1.4.1.164.3.3.3.1.1.1.13 |
| prtGenAlrMaskAll on(3) - will mask all the alarms of the selected port
off(2)- will unmask all alarms of the selected port except
the ones selected by the prtAlrMaskTable.
noOp - will be u… | column | Enumeration | .1.3.6.1.4.1.164.3.3.3.1.1.1.14 |
| prtGenParamStatus This object indicates Status of parameters specific to the
selected port.
- For a port that has no special status or is supported
by prtSExHsfStatTable - 1 Octet: 00hex
… | column | OctetString | .1.3.6.1.4.1.164.3.3.3.1.1.1.15 |
| prtGenRdnStatus This object indicates if this port is part of a redundant pair and in
this case, if it is On or Off.
none(1) - No redundancy or Not Applicable
off (2) - the por… | column | Enumeration | .1.3.6.1.4.1.164.3.3.3.1.1.1.16 |
| prtGenTestMaskXP This is an Expanded test mask of the prtGenTestMask object.
The prtGenTestMask object reached its maximum, being an Integer with 31 bits.
This object indicates which tests from th… | column | OctetString | .1.3.6.1.4.1.164.3.3.3.1.1.1.17 |
| prtGenTestCmdXP This is an Expanded test command of the prtGenTestCmd object.
The prtGenTestCmd object reached its maximum, being an Integer with 31 bits.
Setting this object to a value as detail… | column | OctetString | .1.3.6.1.4.1.164.3.3.3.1.1.1.18 |
| prtGenSlt This attribute indicates a unique number to identify the slot where
the card is inserted in.
When the unit is stand-alone, this object is not applicable
and 255 will be used.
The … | column | Enumeration | .1.3.6.1.4.1.164.3.3.3.1.1.1.2 |
| prtGenExtInt This attribute describes the type of the designated port.
Exteral port is a port with a physical connector. Internal
port might be of two types, one is a composite port which … | column | Enumeration | .1.3.6.1.4.1.164.3.3.3.1.1.1.3 |
| prtGenIfIndex This attribute indicates the unique interface number
assigned to the port. The specific interface of this
attribute is the same as the interface identified by the
value of i… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.3.3.1.1.1.4 |
| prtGenActiveStatus This attribute describes the activity status of the port.
unknown(1) indicates that the information is not supported.
notUsed(2) indicates that the port is not connected according… | column | Enumeration | .1.3.6.1.4.1.164.3.3.3.1.1.1.5 |
| prtGenAlrStatus Indicates the alarm state at port (ch) agent level.
This object will be:
- critical(7): when there is at least one active (ON) critical
alarm .
- major (3): when th… | column | Enumeration | .1.3.6.1.4.1.164.3.3.3.1.1.1.6 |
| prtGenTestStatus This attribute will be on(3) when there is at least one test
in progress (running) on the port; otherwise the value will
be off(2). | column | Enumeration | .1.3.6.1.4.1.164.3.3.3.1.1.1.7 |
| prtGenTestMask This is a mask which indicates which tests from the
'prtGenTestCmd' list are allowed for the selected port.
If a specific test is allowed, its respective bit will be SET
in the m… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.3.3.1.1.1.8 |
| prtGenTestCmd Setting this object to a value as detailed furter on
(except 0) will initiate a test on the specific port,
if the operation is allowed (according to TestMask).
If the operation… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.3.3.1.1.1.9 |