prtGenTestCmdXP
RAD-MIB ·
.1.3.6.1.4.1.164.3.3.3.1.1.1.18
Object
column
r/w
OctetString
This is an Expanded test command of the prtGenTestCmd object.
The prtGenTestCmd object reached its maximum, being an Integer with 31 bits.
Setting this object to a value as detailed furter on
(except 0) will initiate a test on the specific port,
if the operation is allowed (according to TestMaskXP).
If the operation is not allowed, the mux will ignore the
operation.
The test/s requested will be set according to the respective
bit:
TEST BIT
----------- ---
localLoop 1 =LSB
remoteLoop 2
bert 3
plb 4
inband 5
prbs 8
loop2-v54 (RLB) 9
loop3-v54 (LLB) 10
Tone injection 13
Tx-plb 14
Tx-llb 15
DTE loop (HSSI) 16
HDSL-Tx-Inband 20
HDSL-Rx-Inband 21
Monitor 22 (test port)
User Line Loopback 23
Rem-Loop-on-Rem-Unit 25
LBBD 26
LB1 27
LB2 28
BERT-on-Rem-Unit 29
TS Remote Loop 30
LLB-on-Rem-Unit 31
Downstream-AIS 32
Upstream-AIS 33
Send-RDI 34
Test Per TS 35
e.g : If the requested value is 00000003 hex ->
Bits 1 & 2 are set -> the requested tests are :
local-loop
remote-loop
Setting this object to stop (value=0 ; all bits are 0),
will stop all the user requested tests running on the
selected port; it will NOT stop the tests initiated by
the system.
Context
- MIB
- RAD-MIB
- OID
.1.3.6.1.4.1.164.3.3.3.1.1.1.18- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- prtGenEntry
- Table
- prtGenParamTable
- Siblings
- 18
Syntax
OctetString
Values & Constraints
No enumerated values or constraints recorded.
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| prtGenPrtIdx This attribute indicates a unique number to identify a port.
The valid port number depends on the IO slot no., the
installed card type and the port type: outside/external, insi… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.3.3.1.1.1.1 |
| prtGenTestRunning This object indicates which tests are running currently on
the selected port (initiated by user and/or by the system).
If a specific test is currently running on the port, its
r… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.3.3.1.1.1.10 |
| prtGenType This object describes the type of the selected port.
idsl - applicable for external ports of HS-U cards (of DXC) when
interface is LT-1. | column | Enumeration | .1.3.6.1.4.1.164.3.3.3.1.1.1.11 |
| prtGenInterfaceType This attribute indicates a unique HW interface type of the
selected port.
Examples:
- for T1 cards: DSU, CSU
- for E1 cards: DSU, LTU
- for HS cards: v35, rs422, x21
etc... | column | OctetString | .1.3.6.1.4.1.164.3.3.3.1.1.1.12 |
| prtGenAlrClearCmd Setting this attribute to ON, will enforce a clear
operation on the port level alarms . Upon completion,
the value will automatically change to off(2).
noOp - will be used by a… | column | Enumeration | .1.3.6.1.4.1.164.3.3.3.1.1.1.13 |
| prtGenAlrMaskAll on(3) - will mask all the alarms of the selected port
off(2)- will unmask all alarms of the selected port except
the ones selected by the prtAlrMaskTable.
noOp - will be u… | column | Enumeration | .1.3.6.1.4.1.164.3.3.3.1.1.1.14 |
| prtGenParamStatus This object indicates Status of parameters specific to the
selected port.
- For a port that has no special status or is supported
by prtSExHsfStatTable - 1 Octet: 00hex
… | column | OctetString | .1.3.6.1.4.1.164.3.3.3.1.1.1.15 |
| prtGenRdnStatus This object indicates if this port is part of a redundant pair and in
this case, if it is On or Off.
none(1) - No redundancy or Not Applicable
off (2) - the por… | column | Enumeration | .1.3.6.1.4.1.164.3.3.3.1.1.1.16 |
| prtGenTestMaskXP This is an Expanded test mask of the prtGenTestMask object.
The prtGenTestMask object reached its maximum, being an Integer with 31 bits.
This object indicates which tests from th… | column | OctetString | .1.3.6.1.4.1.164.3.3.3.1.1.1.17 |
| prtGenTestRunningXP This is an Expanded object of the prtGenTestRunning object.
The prtGenTestRunning object reached its maximum, being an Integer with 31 bits.
This object indicates which tests are … | column | OctetString | .1.3.6.1.4.1.164.3.3.3.1.1.1.19 |
| prtGenSlt This attribute indicates a unique number to identify the slot where
the card is inserted in.
When the unit is stand-alone, this object is not applicable
and 255 will be used.
The … | column | Enumeration | .1.3.6.1.4.1.164.3.3.3.1.1.1.2 |
| prtGenExtInt This attribute describes the type of the designated port.
Exteral port is a port with a physical connector. Internal
port might be of two types, one is a composite port which … | column | Enumeration | .1.3.6.1.4.1.164.3.3.3.1.1.1.3 |
| prtGenIfIndex This attribute indicates the unique interface number
assigned to the port. The specific interface of this
attribute is the same as the interface identified by the
value of i… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.3.3.1.1.1.4 |
| prtGenActiveStatus This attribute describes the activity status of the port.
unknown(1) indicates that the information is not supported.
notUsed(2) indicates that the port is not connected according… | column | Enumeration | .1.3.6.1.4.1.164.3.3.3.1.1.1.5 |
| prtGenAlrStatus Indicates the alarm state at port (ch) agent level.
This object will be:
- critical(7): when there is at least one active (ON) critical
alarm .
- major (3): when th… | column | Enumeration | .1.3.6.1.4.1.164.3.3.3.1.1.1.6 |
| prtGenTestStatus This attribute will be on(3) when there is at least one test
in progress (running) on the port; otherwise the value will
be off(2). | column | Enumeration | .1.3.6.1.4.1.164.3.3.3.1.1.1.7 |
| prtGenTestMask This is a mask which indicates which tests from the
'prtGenTestCmd' list are allowed for the selected port.
If a specific test is allowed, its respective bit will be SET
in the m… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.3.3.1.1.1.8 |
| prtGenTestCmd Setting this object to a value as detailed furter on
(except 0) will initiate a test on the specific port,
if the operation is allowed (according to TestMask).
If the operation… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.3.3.1.1.1.9 |