prtExPh1MlLineCode

RAD-MIB · .1.3.6.1.4.1.164.3.2.3.2.2.1.1.6

Object

column r/w Enumeration

This attribute is the line code parameter used for T1/E1
interface.
The user should select only the parameters which are relevant
to the specific card:
T1 line code parameters for MPH.1/T1
E1 line code parameters for MPH.1/E1.
This parameter has the same values as dsx1LineCoding in T1/E1
MIB (RFC-1406).  The parameters in dsx1LineCoding are:
dsx1JBZS  (1)
dsx1B8ZS  (2)
dsx1HDB3  (3)
dsx1ZBTSI (4)
dsx1AMI   (5)
other     (6)

Context

MIB: RAD-MIB
OID: .1.3.6.1.4.1.164.3.2.3.2.2.1.1.6
Type: column
Access: readwrite
Status: current
Parent: prtExPh1MlCnfgEntry
Table: prtExPh1MlCnfgTable
Siblings: 31

Syntax

Enumeration

Values & Constraints

No enumerated values or constraints recorded.

Related Objects

Sibling Objects

Object	Type	Syntax	OID
prtExPh1MlCnfgIdx This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.	column	Integer32	`.1.3.6.1.4.1.164.3.2.3.2.2.1.1.1`
prtExPh1MlRxSensitivity This attribute is the rx line sensitivity parameter. low26dBm, high36dBm - applicable for T1-CSU shortHaul, longHaul - applicable for MTML-4 cards low15dbm was added for vmux110/2…	column	Enumeration	`.1.3.6.1.4.1.164.3.2.3.2.2.1.1.10`
prtExPh1MlIdleCode Determines the code for transmission in empty time slots. Type value(00-FFH), Excluding 0H,8H,10H,12H,21H,24H,42H,49H, 84H,92H	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.164.3.2.3.2.2.1.1.11`
prtExPh1MlTdmTrunk This attribute indicates whether the port is used to transfer TDM cards data and through which Bus.	column	Enumeration	`.1.3.6.1.4.1.164.3.2.3.2.2.1.1.12`
prtExPh1MlClkMode Defines the clock operation mode of the T1/E1 interface. Ports that are connected to the TDM Buses must be in nodalTiming(3) clock mode.	column	Enumeration	`.1.3.6.1.4.1.164.3.2.3.2.2.1.1.13`
prtExPh1MlMfClkSrcSlt This attribute indicates whether the port Tx multiframe is synchronized with Rx multiframe of another port and the slot position of that port. This operation is required in order …	column	Enumeration	`.1.3.6.1.4.1.164.3.2.3.2.2.1.1.14`
prtExPh1MlMfClkSrcPrt A unique number to identify a port position in the mux. It has no effect when the prtExPh1MlMfClkSrcSlt selected is Local. inPrt1 - for MTML-H/E1 cards.	column	Enumeration	`.1.3.6.1.4.1.164.3.2.3.2.2.1.1.15`
prtExPh1MlFdlType A unique number to identify the side of the FDL operation. Normal: 'response' for the user side and 'command' for the PTT side. Applicable only when working with ESF-T1 link	column	Enumeration	`.1.3.6.1.4.1.164.3.2.3.2.2.1.1.16`
prtExPh1MlInbandMng A unique number to identify an Inband management over the link.	column	Enumeration	`.1.3.6.1.4.1.164.3.2.3.2.2.1.1.17`
prtExPh1MlInbandMngRate A unique number to identify the rate of the Inband management (Kbps). E1 port - it is not applicable when prtExPh1MlInbandMng selected is off. T1 port - it is not applic…	column	Enumeration	`.1.3.6.1.4.1.164.3.2.3.2.2.1.1.18`
prtExPh1MlRedundType This object determines the ML redundancy type: none - no ML redundacy dualCableAIS - each ML card is connected by a separate dualCableParallelTx cable to the other MUX (t…	column	Enumeration	`.1.3.6.1.4.1.164.3.2.3.2.2.1.1.19`
prtExPh1MlSltIdx This attribute indicates a unique slot position where the module is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid. For the Vmux2100 Main Board notApplicabl…	column	Enumeration	`.1.3.6.1.4.1.164.3.2.3.2.2.1.1.2`
prtExPh1MlRedundSlot This object indicates the slot containing the redundacy ML card, coupled with the current ML (prtExPh1MlSltIdx). When prtExPh1MlRedundType=none (no ML redundancy) this object will…	column	Enumeration	`.1.3.6.1.4.1.164.3.2.3.2.2.1.1.20`
prtExPh1MlRedundPort This object indicates the redundacy ML port, coupled with the current ML port (prtExPh1MlPrtIdx). When prtExPh1MlRedundType=none (no ML redundancy) this object will be 'notApplica…	column	Enumeration	`.1.3.6.1.4.1.164.3.2.3.2.2.1.1.21`
prtExPh1MlRedundRecTime Redundancy Recovery Time (sec). After switching the ML card to the current (prtExPh1MlSltIdx), the next ML switch can be performed only after a minimum time, indicated by this obj…	column	Integer32	`.1.3.6.1.4.1.164.3.2.3.2.2.1.1.22`
prtExPh1MlInbandMngRoutProt This attribute indicates the Inband Mng routing protocol of the port.	column	Enumeration	`.1.3.6.1.4.1.164.3.2.3.2.2.1.1.23`
prtExPh1MlIfType Interface type of the port. For T1 - csu, dsu are the valid values For E1 - dsu, ltu are the valid values.	column	Enumeration	`.1.3.6.1.4.1.164.3.2.3.2.2.1.1.24`
prtExPh1MlMultiplier The data rate of each TS. The multiplier values can be 56 kbps or 64 kbps.	column	Enumeration	`.1.3.6.1.4.1.164.3.2.3.2.2.1.1.25`
prtExPh1MlSupportedTS Number of Supported Time Slots by the agent. For Vmux-110 there is HW that supports less than 31/24 Time Slots for the E1/T1 port.	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.164.3.2.3.2.2.1.1.26`
prtExPh1MlImpedance The Line Impedance. For T1 (always balanced), impedance is 100 ohm. For E1: - balanced = 120 ohm - unbalanced = 75 ohm.	column	Enumeration	`.1.3.6.1.4.1.164.3.2.3.2.2.1.1.27`
prtExPh1MlQ50BwControl This object enables configuration of Q.50 Bandwidth Control on the port. If the bandwidth exceeds a certain threshold it is possible to disable new calls in the PBX via Q.50 proto…	column	Enumeration	`.1.3.6.1.4.1.164.3.2.3.2.2.1.1.28`
prtExPh1MlQ50SignalPair Q.50 Signaling bits Pair that is currently in use: A&B bits or C&D bits. For Annex B it will always be: aAndB (2).	column	Enumeration	`.1.3.6.1.4.1.164.3.2.3.2.2.1.1.29`
prtExPh1MlPrtIdx This attribute indicates a unique port number. MP-2100/2200: MTML-1/E1 and MTML-1/T1 cards have only one external interface. inPrt1, inPrt2 - for MTML-H/2E1 and HSH cards. inPrt1…	column	Enumeration	`.1.3.6.1.4.1.164.3.2.3.2.2.1.1.3`
prtExPh1MlInternalSwitch This parameter shows whether the data will be transferred from one port to the other port within the same group of 2 ports. The default value is: Enable. Disable value mig…	column	Enumeration	`.1.3.6.1.4.1.164.3.2.3.2.2.1.1.30`
prtExPh1MlSigService Signaling Service given by this link. notApplicable - for T1 links normal - usual Signaling advanced - V5 Signaling.	column	Enumeration	`.1.3.6.1.4.1.164.3.2.3.2.2.1.1.31`
prtExPh1MlFragmentSize This parameter indicates the maximum number of bytes permitted in a packet send over the Link. Exceeding this size will cause packet fragmentation.	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.164.3.2.3.2.2.1.1.32`
prtExPh1MlConnect This attribute indicates whether the port should be considered in any of the mux algorithms. It also affects all the card considerations because it may indicate that the module h…	column	Enumeration	`.1.3.6.1.4.1.164.3.2.3.2.2.1.1.4`
prtExPh1MlLineType This attribute is the line type parameter for T1/E1 interface. The user should select only the values which are relevant to the specific port: (2),(3), (8) - for T1 port (4)..(7)…	column	Enumeration	`.1.3.6.1.4.1.164.3.2.3.2.2.1.1.5`
prtExPh1MlLineLen This attribute is the line length parameter used only for T1/DSU interfaces. lenXXXpXXXft = len-XXX-XXXft.	column	Enumeration	`.1.3.6.1.4.1.164.3.2.3.2.2.1.1.7`
prtExPh1MlRestoreTime The time passing from the disappearance of the loss of synchronization condition (red alarm) to the restoration of normal service. The options 1secFast(2) and 10sec62411(3) for E1…	column	Enumeration	`.1.3.6.1.4.1.164.3.2.3.2.2.1.1.8`
prtExPh1MlTxGain This attribute is the tx gain parameter used only for T1/CSU interfaces.	column	Enumeration	`.1.3.6.1.4.1.164.3.2.3.2.2.1.1.9`