prtExPVc4SignalingProtocol
RAD-MIB ·
.1.3.6.1.4.1.164.3.2.3.2.9.1.1.24
Object
column
r/w
Enumeration
The signaling protocol that will be used between the PABX & the voice port.
Delay Start Protocol: the line is seized by sending an Off hook signal
and after a delay, if the called party is available (On hook)
DTMF (Dual Tone Multi Frequency) digits are sent towards the called party.
Immediate Start Protocol: the line is seized by sending an Off Hook signal
and immediately DTMF digits are sent towards the called party.
Wink start protocol: the line is seized by sending an Off Hook signal
and then the called party sends a short Off Hook wink signal.
Now the calling party starts sending DTMF digits.
Context
- MIB
- RAD-MIB
- OID
.1.3.6.1.4.1.164.3.2.3.2.9.1.1.24- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- prtExPVc4CnfgEntry
- Table
- prtExPVc4CnfgTable
- Siblings
- 51
Syntax
Enumeration
Values & Constraints
Object Constraints
range: 1-255
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| prtExPVc4CnfgIdx This attribute indicates the Idx of the Cnfg (1..100) being
accessed.
Idx 255 relates to the TmpCnfg | column | Integer32 | .1.3.6.1.4.1.164.3.2.3.2.9.1.1.1 |
| prtExPVc4Tc Time interval for CIR control, in seconds. The value will
be the same for all cards' ports. | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.9.1.1.10 |
| prtExPVc4Oos Handling type, when connection is lost. | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.9.1.1.11 |
| prtExPVc4EchoCanceler Echo canceler activation. | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.9.1.1.12 |
| prtExPVc4VarDelay Maximum variant delay of the FR network, in msec. | column | Integer32 | .1.3.6.1.4.1.164.3.2.3.2.9.1.1.13 |
| prtExPVc4CongLevel This object indicates the level of delayed data in
precents of total available dynamic memory,
for which the port will start to operate as congested.
The resolution of the paramet… | column | Integer32 | .1.3.6.1.4.1.164.3.2.3.2.9.1.1.14 |
| prtExPVc4Wire This object indicates the wiring of the E&M port.
It is applicable only for E&M card type. | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.9.1.1.15 |
| prtExPVc4ExtensionType This object indicates the type of extension relevant for this port.
ipForceConnect (6) is used for automatic connection or automatic
dialing when the phone is off h… | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.9.1.1.16 |
| prtExPVc4ExtensionNumber This is the extension number of this port.
This field is relevant only when the extension
type is voice switching and is read only if the
port is member of a hunt group. | column | OctetString | .1.3.6.1.4.1.164.3.2.3.2.9.1.1.17 |
| prtExPVc4OutPulsing This field indicates whether to outpulse the received
digits. It is notApplicable(1) when the extension type
is forceConnect(2). | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.9.1.1.18 |
| prtExPVc4HuntGroupMb This object indicates if this port belongs to
an hunt group. | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.9.1.1.19 |
| prtExPVc4SltIdx This attribute indicates a unique slot position where
the card is inserted. | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.9.1.1.2 |
| prtExPVc4HuntGroupIdx If it belongs to an hunt group, this fields
indicates the index of the relevant hunt group.
0 = notApplicable | column | Integer32 | .1.3.6.1.4.1.164.3.2.3.2.9.1.1.20 |
| prtExPVc4AutoFaxMode This object indicates if the system will switch automatically to
FAX mode when detecting FAX activity.
Default=Yes. | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.9.1.1.21 |
| prtExPVc4FaxRate FAX initial rate.
Default=9600 bps. | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.9.1.1.22 |
| prtExPVc4SeizeAck This parameter shows whether the device will acknowledge
a seize signal (On/Off Hook).
When the value is set to yes(3) & the device receives an on/off hook signal
it will transmit… | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.9.1.1.23 |
| prtExPVc4DelayStart This parameter is used only for Delay Protocol.
This is the time that the calling party will wait after sending an Off hook
signal and before sending DTMF digits to the called par… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.2.3.2.9.1.1.25 |
| prtExPVc4WinkMinDuration This parameter is used only for Wink Protocol.
Min Duration of the Wink Signal (off hook duration from the called party).
Legal values: 40..400 msec in intervals of 10 msec. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.2.3.2.9.1.1.26 |
| prtExPVc4WinkMaxDuration This parameter is used only for Wink Protocol.
Max Duration of the Wink Signal (off hook duration from the called party).
Legal values: 40..400 msec in intervals of 10 msec. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.2.3.2.9.1.1.27 |
| prtExPVc4GenerateTone This parameter indicates whether the device (MX or MPH) should generate
dial tones for the channel.
If the value is yes (3), it generates dial tones.
If the value is no (2), the … | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.9.1.1.28 |
| prtExPVc4CodingLaw This attribute indicates the Method/Law for decoding/encoding the voice
information.
aLaw(1) is the standard Law for E1 links.
uLaw(2) is the standard Law for T1 links.
… | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.9.1.1.29 |
| prtExPVc4PrtIdx This object indicates the port number in the selected card
(slot). | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.9.1.1.3 |
| prtExPVc4GenerateRingBack Determines whether the Ring Back tone is generated locally or from the
remote end.
The default is - NO (Meaning coming from the remote end).
Yes means that the Ring Back T… | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.9.1.1.30 |
| prtExPVc4ChannelId Channel Identifier.
According to FRF11 each voice port that works as force connect should add a
CH Id after the DLCI in the frame header.
Default : 1
… | column | Integer32 | .1.3.6.1.4.1.164.3.2.3.2.9.1.1.31 |
| prtExPVc4PortConnection Port connection determines whether the port is connected to a PABX (Trunk) or to
Telephone set (Line) .
It determines whether to send certain messages to the port o… | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.9.1.1.32 |
| prtExPVc4CoderAndRate Coder and Rate for the Voice Compression.
In MPH: Relevant for MVC-8 card only. | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.9.1.1.33 |
| prtExPVc4DestinationNum The destination phone number: 0 to 22 digits.
Applicable for Auto Dial - ipForceConnect(6), Permanent Dial and
Auto Accept Extension Types.
Default: Null Str… | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.164.3.2.3.2.9.1.1.34 |
| prtExPVc4DtmfRelay When DTMF RELAY is disabled, the DTMF digits (dialed by the user)
are transmitted as compressed voice and in the remote unit are decompressed.
When DTMF RELAY is en… | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.9.1.1.35 |
| prtExPVc4DiscOnSilence No. of silenced seconds after which the call will be disconected.
A value of 0 means that there will be no disconnect when there is silence.
Possible values: 0 - 900 sec. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.2.3.2.9.1.1.36 |
| prtExPVc4DynamicJitter The MVC8 uses two mechanisms to overcome the network delay.
The first one is a static jitter buffer which holds a constant buffer of up
to 300 Msec and can be controled by the JIT… | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.9.1.1.37 |
| prtExPVc4EandMType This is the signaling type on the E&M analog side.
The analog signaling includes voltage, no. of pins and other parameters. | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.9.1.1.38 |
| prtExPVc4Rate This is the Rate of the port in TS units. It is used by VF-30 card family.
0 = NA = port is not intended to be connected; therefore, no Rate. | column | Integer32 | .1.3.6.1.4.1.164.3.2.3.2.9.1.1.39 |
| prtExPVc4PrtType This object indicates the type of the selected port.
In Mx 30/300 phase 4: s0 & u are for Voice over ISDN.
In MX 30/300 phase 5: sQsig & uQsig are used for Voice over ISDN with Qs… | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.9.1.1.4 |
| prtExPVc4FrameSize Defines the maximum size in Bytes of the multiplexed frame.
In some cases this must be limited to avoid IP fragmentation,
which makes the multiplexing useless, and can also decrea… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.2.3.2.9.1.1.40 |
| prtExPVc4MultiplexInterval Defines the maximum amout of time (msec.) between multiplexed frames
that are sent.
For Vmux-400/420 devices:
It defines the Payload Packetizing Interval.
… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.2.3.2.9.1.1.41 |
| prtExPVc4TransportProtocol Transport Protocol.
ptp = point to point.
aal2oMpls = AAL2 over MPLS. | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.9.1.1.42 |
| prtExPVc4MultiFreqRelay This object enables/disables Multi Frequency Signaling Detection. | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.9.1.1.43 |
| prtExPVc4MinPulseWidth Defines the minimum Pulse Width in msec.
Valid values: 45-100 msec.
notApplicable=0. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.2.3.2.9.1.1.44 |
| prtExPVc4MinPowerLevel Defines the minimum Power Level in dBm.
Valid values: -1..-35 dBm. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.2.3.2.9.1.1.45 |
| prtExPVc4SuperTandem The Super Tandem feature provides end to end compression
over multiple hops, solving the double compression problem
detected in Voice compressing systems.
The Super Tandem, when… | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.9.1.1.46 |
| prtExPVc4DestIp This object defines the destination IP Address. | column | RFC1155-SMIIpAddress | .1.3.6.1.4.1.164.3.2.3.2.9.1.1.47 |
| prtExPVc4DestBundle This object defines the destination Bundle at the
far-end device. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.2.3.2.9.1.1.48 |
| prtExPVc4SrcIpAddress This object defines the Source IP Address. | column | RFC1155-SMIIpAddress | .1.3.6.1.4.1.164.3.2.3.2.9.1.1.49 |
| prtExPVc4Connect This attribute indicates whether the port should be
considered in any of the mux algorithms. | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.9.1.1.5 |
| prtExPVc4SrcIpMask This object defines the Source IP Mask. | column | RFC1155-SMIIpAddress | .1.3.6.1.4.1.164.3.2.3.2.9.1.1.50 |
| prtExPVc4DefaultGateway This object defines the Default Gateway for this interface. | column | RFC1155-SMIIpAddress | .1.3.6.1.4.1.164.3.2.3.2.9.1.1.51 |
| prtExPVc4SigPacketInterval Defines the Signaling Packetizing Interval,
which is the maximum time interval, measured in msec (milliseconds),
between multiplexed signaling frames. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.164.3.2.3.2.9.1.1.52 |
| prtExPVc4IfType This attribute indicates the interface type of the port.
eAndM4wires and eAndM2wires - are valid only for E&M
port type
eAndM4wires - means 2/4 … | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.9.1.1.6 |
| prtExPVc4TxGain Transmission gain in dB. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.2.3.2.9.1.1.7 |
| prtExPVc4RxGain Reception gain in dBm. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.2.3.2.9.1.1.8 |
| prtExPVc4MaxRate Voice rate. | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.9.1.1.9 |