pktSwchFrDlcmiPollingInterval
RAD-MIB ·
.1.3.6.1.4.1.164.8.8.3.1.11
Object
column
Integer32
This is the number of seconds between succes- sive status enquiry messages.
Context
- MIB
- RAD-MIB
- OID
.1.3.6.1.4.1.164.8.8.3.1.11- Type
- column
- Access
- readonly
- Status
- current
- Parent
- pktSwchFrAEntry
- Table
- pktSwchFrATable
- Siblings
- 18
Syntax
Integer32
Values & Constraints
Object Constraints
range: 0-65000
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| pktSwchFrIfIndexA This is the ifIndex of the frame relay port. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.8.8.3.1.1 |
| pktSwchFrNrzModeA The data encoding format. | column | Enumeration | .1.3.6.1.4.1.164.8.8.3.1.10 |
| pktSwchFrDlcmiFullEnquiryInterval Number of status enquiry intervals that pass
before issuance of a full status enquiry mes-
sage. | column | Integer32 | .1.3.6.1.4.1.164.8.8.3.1.12 |
| pktSwchFrDlcmiErrorThreshold This is the maximum number of unanswered
Status Enquiries the equipment shall accept be-
fore declaring the interface down. | column | Integer32 | .1.3.6.1.4.1.164.8.8.3.1.13 |
| pktSwchFrDlcmiMonitoredEvents This is the number of status polling intervals
over which the error threshold is counted. For
example, if within 'MonitoredEvents' number of
events the station receives 'Erro… | column | Integer32 | .1.3.6.1.4.1.164.8.8.3.1.14 |
| pktSwchFrDlciHeaderModeA Dlci Header length for this FR port. Option 4 means that there
will be no management Dlci in the range of 1024 to 8388607.
The management Dlci will be in the range of 0-15 or 991-… | column | Enumeration | .1.3.6.1.4.1.164.8.8.3.1.15 |
| pktSwchFrDcdLinkFailureA Link Failure Detection by DCD.
If Link Failure detection by DCD is on - (3), when the DCD is
down, the FR SW will detect it and change the FR link status
from UP to DOWN. A trap o… | column | Enumeration | .1.3.6.1.4.1.164.8.8.3.1.16 |
| pktSwchFrTxIdlesA This parameter shows whether the PS will Transmit Idles between
frames and control the RTS pin.
Default: no(2). | column | Enumeration | .1.3.6.1.4.1.164.8.8.3.1.17 |
| pktSwchFrOperationModeA When H/W Control is configured, the SCC H/W will detect the change in the
DCD or CTS signals and Start or Stop transmission automatically.
When S/W Control is configured the S/W w… | column | Enumeration | .1.3.6.1.4.1.164.8.8.3.1.18 |
| pktSwchFrPhysInterfOptionsA This is the physical interface.
Note that the DDS physical interface H/W does not exist in the FPS-8.
It is relevant for other PS devices only.
For FPS-8 only the default (noOptio… | column | Enumeration | .1.3.6.1.4.1.164.8.8.3.1.19 |
| pktSwchFrMaintProtA This defines what maintenance protocol is running over this port.
0 - No maintenance protocol.
1 - ANSI PVC maintenance protocol running on DLCI number 0.
2 - LMI maintenance prot… | column | Integer32 | .1.3.6.1.4.1.164.8.8.3.1.2 |
| pktSwchFrMaintModeA This defines the mode of maintenance protocol running over this port. | column | Enumeration | .1.3.6.1.4.1.164.8.8.3.1.3 |
| pktSwchFrRxPoolRedLineA When the number of empty receive buffers at the port reaches this figure (of frames),
the port receiver is congested. This field value should be less than the Rx pool OK field. | column | Integer32 | .1.3.6.1.4.1.164.8.8.3.1.4 |
| pktSwchFrRxPoolOkA Clear the receive congestion condition when the number of empty receive buffers at the port
reaches this figure. This value (of frames) should be greater than the Rx pool red lin… | column | Integer32 | .1.3.6.1.4.1.164.8.8.3.1.5 |
| pktSwchFrTxPoolRedLineA When the number of frames awaiting transmission reaches this figure,
the port transmitter is congested. This field value should be greater than the Tx pool OK field. | column | Integer32 | .1.3.6.1.4.1.164.8.8.3.1.6 |
| pktSwchFrTxPoolOkA Clear the transmit congestion condition when the number of frames awaiting transmission
at the port reaches this figure. This value (of frames) should be less than the Tx pool re… | column | Integer32 | .1.3.6.1.4.1.164.8.8.3.1.7 |
| pktSwchFrTxCeilingA The maximum allowable transmit pool for this port. | column | Integer32 | .1.3.6.1.4.1.164.8.8.3.1.8 |
| pktSwchFrInternalClockA The baud rate of the internal clock. | column | Enumeration | .1.3.6.1.4.1.164.8.8.3.1.9 |