pktSwchFrDlcmiMonitoredEvents

RAD-MIB · .1.3.6.1.4.1.164.8.8.3.1.14

MIB view Table view

Object

column Integer32

This is the number of status polling intervals
over which the error threshold is counted.  For
example, if within 'MonitoredEvents' number  of
events  the  station  receives 'ErrorThreshold'
number of errors, the interface  is  marked  as
down.

Context

MIB: RAD-MIB
OID: .1.3.6.1.4.1.164.8.8.3.1.14
Type: column
Access: readonly
Status: current
Parent: pktSwchFrAEntry
Table: pktSwchFrATable
Siblings: 18

Syntax

Integer32

Values & Constraints

Enumerated Values

`1`	valid
`2`	createRequest
`3`	underCreation
`4`	invalid

Related Objects

Sibling Objects

Object	Type	Syntax	OID
pktSwchFrIfIndexA This is the ifIndex of the frame relay port.	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.164.8.8.3.1.1`
pktSwchFrNrzModeA The data encoding format.	column	Enumeration	`.1.3.6.1.4.1.164.8.8.3.1.10`
pktSwchFrDlcmiPollingInterval This is the number of seconds between succes- sive status enquiry messages.	column	Integer32	`.1.3.6.1.4.1.164.8.8.3.1.11`
pktSwchFrDlcmiFullEnquiryInterval Number of status enquiry intervals that pass before issuance of a full status enquiry mes- sage.	column	Integer32	`.1.3.6.1.4.1.164.8.8.3.1.12`
pktSwchFrDlcmiErrorThreshold This is the maximum number of unanswered Status Enquiries the equipment shall accept be- fore declaring the interface down.	column	Integer32	`.1.3.6.1.4.1.164.8.8.3.1.13`
pktSwchFrDlciHeaderModeA Dlci Header length for this FR port. Option 4 means that there will be no management Dlci in the range of 1024 to 8388607. The management Dlci will be in the range of 0-15 or 991-…	column	Enumeration	`.1.3.6.1.4.1.164.8.8.3.1.15`
pktSwchFrDcdLinkFailureA Link Failure Detection by DCD. If Link Failure detection by DCD is on - (3), when the DCD is down, the FR SW will detect it and change the FR link status from UP to DOWN. A trap o…	column	Enumeration	`.1.3.6.1.4.1.164.8.8.3.1.16`
pktSwchFrTxIdlesA This parameter shows whether the PS will Transmit Idles between frames and control the RTS pin. Default: no(2).	column	Enumeration	`.1.3.6.1.4.1.164.8.8.3.1.17`
pktSwchFrOperationModeA When H/W Control is configured, the SCC H/W will detect the change in the DCD or CTS signals and Start or Stop transmission automatically. When S/W Control is configured the S/W w…	column	Enumeration	`.1.3.6.1.4.1.164.8.8.3.1.18`
pktSwchFrPhysInterfOptionsA This is the physical interface. Note that the DDS physical interface H/W does not exist in the FPS-8. It is relevant for other PS devices only. For FPS-8 only the default (noOptio…	column	Enumeration	`.1.3.6.1.4.1.164.8.8.3.1.19`
pktSwchFrMaintProtA This defines what maintenance protocol is running over this port. 0 - No maintenance protocol. 1 - ANSI PVC maintenance protocol running on DLCI number 0. 2 - LMI maintenance prot…	column	Integer32	`.1.3.6.1.4.1.164.8.8.3.1.2`
pktSwchFrMaintModeA This defines the mode of maintenance protocol running over this port.	column	Enumeration	`.1.3.6.1.4.1.164.8.8.3.1.3`
pktSwchFrRxPoolRedLineA When the number of empty receive buffers at the port reaches this figure (of frames), the port receiver is congested. This field value should be less than the Rx pool OK field.	column	Integer32	`.1.3.6.1.4.1.164.8.8.3.1.4`
pktSwchFrRxPoolOkA Clear the receive congestion condition when the number of empty receive buffers at the port reaches this figure. This value (of frames) should be greater than the Rx pool red lin…	column	Integer32	`.1.3.6.1.4.1.164.8.8.3.1.5`
pktSwchFrTxPoolRedLineA When the number of frames awaiting transmission reaches this figure, the port transmitter is congested. This field value should be greater than the Tx pool OK field.	column	Integer32	`.1.3.6.1.4.1.164.8.8.3.1.6`
pktSwchFrTxPoolOkA Clear the transmit congestion condition when the number of frames awaiting transmission at the port reaches this figure. This value (of frames) should be less than the Tx pool re…	column	Integer32	`.1.3.6.1.4.1.164.8.8.3.1.7`
pktSwchFrTxCeilingA The maximum allowable transmit pool for this port.	column	Integer32	`.1.3.6.1.4.1.164.8.8.3.1.8`
pktSwchFrInternalClockA The baud rate of the internal clock.	column	Enumeration	`.1.3.6.1.4.1.164.8.8.3.1.9`