alarmForwardingCause
RAD-MIB ·
.1.3.6.1.4.1.164.6.2.50.1.6
Object
column
r/w
Bits
Bit map representing the cause upon which alarm forwarding will take place. bit 0 - LOSS (LINE DOWN) bit 1 - AIS bit 2 - RDI bit 3 - PROTOCOL DOWN. bit 4 - OAM Signaling - EFM bit 5 - OAM Signaling - CFM.
Context
- MIB
- RAD-MIB
- OID
.1.3.6.1.4.1.164.6.2.50.1.6- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- alarmForwardingEntry
- Table
- alarmForwardingTable
- Siblings
- 10
Syntax
Bits
Values & Constraints
Object Constraints
range: 1-255
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| alarmForwardingFailPort An Index of the port on which a fail occurs. | column | Integer32 | .1.3.6.1.4.1.164.6.2.50.1.1 |
| alarmForwardingDirection This parameter determines the Direction of the Alarm Forwarding.
unidirectional - alarmForwardingFailPort affects the
alarmForwardingToPort.
bidirectional - alar… | column | Enumeration | .1.3.6.1.4.1.164.6.2.50.1.10 |
| alarmForwardingAction Bit map representing the action to be performed when alarm forwarding will take place.
bit 0 - No Action.
'1' value - device should NOT perform any action, though other b… | column | Bits | .1.3.6.1.4.1.164.6.2.50.1.11 |
| alarmForwardingToPort An Index of the port that will be affected
upon the failure of the alarmForwardingFailPort. | column | Integer32 | .1.3.6.1.4.1.164.6.2.50.1.2 |
| alarmForwardingRowStatus Creation/ Deletion of rows in the table. | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.164.6.2.50.1.3 |
| alarmForwardingRecoveryTime This parameter defines the maximum time (sec)
the affected port will hold the down state. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.6.2.50.1.4 |
| alarmForwardingGroupConditions This parameter is applicable when there is a group of interfaces
in which a fault may occur, and one interface to which alarm is propagated (forwarded).
0 = All - Forwarding will… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.6.2.50.1.5 |
| alarmForwardingRecoveryMode This parameter determines the Recovery Mode.
manual - The user should stop the alarm forwarding
by using the alarmForwardingRecoveryCommand.
automatic - Alarm forwarding will be… | column | Enumeration | .1.3.6.1.4.1.164.6.2.50.1.7 |
| alarmForwardingRecoveryCommand This parameter is a command. It is applicable when
alarmForwardingRecoveryMode = manual.
on - Will stop alarm forwarding.
After setting to 'On', the agent will set this paramete… | column | Enumeration | .1.3.6.1.4.1.164.6.2.50.1.8 |
| alarmForwardingDelay This parameter determines the period of time (in seconds) the
alarm of the alarmForwardingFailPort should exist before
starting alarm forwarding. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.164.6.2.50.1.9 |