adslConfTxEndFreqBin
RAD-MIB ·
.1.3.6.1.4.1.164.3.1.6.10.1.1.9
Object
This parameter controls Transmit End Bin number. For ADSL Annex A - range of values is 6 to 31. For ADSL Annex B - range of values is 33 to 63. requency (in khz unit) is calculated by multiplying this value by bin bandwidth (4Khz)
Context
- MIB
- RAD-MIB
- OID
.1.3.6.1.4.1.164.3.1.6.10.1.1.9- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- adslConfEntry
- Table
- adslConfTable
- Siblings
- 13
Syntax
SNMPv2-SMIInteger32
- Source
- SNMPv2-SMIInteger32
- Base type
Integer32
Values & Constraints
Enumerated Values
1 | notApplicable |
2 | enhanced |
3 | disabled |
Type Constraints
range: -2147483648..2147483647
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| adslConfCnfgIdx This object indicates the Idx of the Config being accessed.
Idx of 255 relates to the Temporary (Scratch) Config.
For products that support several configurations,
Set can be per… | column | Integer32 | .1.3.6.1.4.1.164.3.1.6.10.1.1.1 |
| adslConfRxStartFreqBin This parameter controls Receive Start Bin number.
Range of values for this parameter depends on ADSL Annex supported,
and transmisson mode (adslTransmissionMode) selected:
ADSL… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.1.6.10.1.1.10 |
| adslConfRxEndFreqBin This parameter controls Receive End Bin number.
Range of values for this parameter depends on ADSL Annex supported,
and transmisson mode (adslTransmissionMode) selected:
ADSL A… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.1.6.10.1.1.11 |
| adslConfTxPowerAttenuation This parameter controls Transmit Gain in dB units
Range is 0 to 12dB. Resolution is 1 dB | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.1.6.10.1.1.12 |
| adslConfPSDMask This parameter controls Power Spectral Density Mask.
This object is applicable only for ADSL2.
(adslConfStandardCompliance is one of the following:
adsl2, adsl2Plus, adsl2Auto,… | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.10.1.1.13 |
| adslConfCommand This parameter enables the user to perform commands on ADSL.
off(1) - default state.
After any operation ends, value should be automatically
set to off(1).
restart(2) -… | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.10.1.1.14 |
| adslConfFramingType ADSL Frame type | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.10.1.1.2 |
| adslConfPilotToneRequest This parameter controls Pilot Tone Request (PTR). | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.10.1.1.3 |
| adslConfTrellisCoding This parameter enables/disables Trellis error detection code.
using error detection code may introduce delays. | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.10.1.1.4 |
| adslConfTransmissionMode This parameter controls transmision mode:
Echo Cancellation is required when both ATU-C an ATU-R use
the same frequency.
Frequency Division (different frequency ranges for ATU-C … | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.10.1.1.5 |
| adslConfStandardCompliance This parameter indicates standard compliance
G.Lite enables extended ADSL range, ease of installation,
but requires lower rate. | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.10.1.1.6 |
| adslConfMaxBitPerBin This parameter indicates maximum number of bits per ADSL Bin.
Each Bin has bandwidth of 4khz.
Range of values for this parameter is 0..15 | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.1.6.10.1.1.7 |
| adslConfTxStartFreqBin This parameter controls Transmit Start Bin number.
For ADSL Annex A - range of values is 6 to 31.
For ADSL Annex B - range of values is 33 to 63.
Frequency (in khz unit) is cal… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.1.6.10.1.1.8 |