atsConfigFrequencyDeviation
PowerNet-MIB ·
.1.3.6.1.4.1.318.1.1.8.4.12
Object
scalar
mandatory
r/w
Enumeration
To configure the frequency deviation. AP77xx units may use 1, 2, or 3 (Hz). AP44xx and AP44xxA units may use 3, 5, or 10 (Hz).
Context
- MIB
- PowerNet-MIB
- OID
.1.3.6.1.4.1.318.1.1.8.4.12- Type
- scalar
- Access
- readwrite
- Status
- mandatory
- Parent
- atsConfig
- Siblings
- 17
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | one |
2 | two |
3 | three |
5 | five |
10 | ten |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| atsConfigProductName mandatory A configurable character string. | scalar | RFC1213-MIBDisplayString | .1.3.6.1.4.1.318.1.1.8.4.1 |
| atsConfigLineVRMSMediumLimit mandatory To configure the Line VRMS Medium Limit. | scalar | Integer32 | .1.3.6.1.4.1.318.1.1.8.4.10 |
| atsConfigLineVRMSWideLimit mandatory To configure the Line VRMS Wide Limit. | scalar | Integer32 | .1.3.6.1.4.1.318.1.1.8.4.11 |
| atsConfigBankTableSize mandatory The size of the bank table. | scalar | Integer32 | .1.3.6.1.4.1.318.1.1.8.4.13 |
| atsConfigBankTable mandatory Allows for configuration of each ATS bank. | table | - | .1.3.6.1.4.1.318.1.1.8.4.14 |
| atsConfigPhaseTableSize mandatory The size of the phase table. | scalar | Integer32 | .1.3.6.1.4.1.318.1.1.8.4.15 |
| atsConfigPhaseTable mandatory Allows for configuration of each ATS phase. | table | - | .1.3.6.1.4.1.318.1.1.8.4.16 |
| atsConfigDeviceLocation mandatory A user-defined string identifying the location
of the ATS | scalar | RFC1213-MIBDisplayString | .1.3.6.1.4.1.318.1.1.8.4.17 |
| atsConfigContact mandatory A user-defined string identifying the
person to contact regarding the ATS | scalar | RFC1213-MIBDisplayString | .1.3.6.1.4.1.318.1.1.8.4.18 |
| atsConfigPreferredSource mandatory This variable returns the preferred source of power when both sources are OK. | scalar | Enumeration | .1.3.6.1.4.1.318.1.1.8.4.2 |
| atsConfigFrontPanelLockout mandatory Setting this variable to disableFrontPanel(1), prevents source
preference configuration of the Automatic Transfer Switch via the
Front Panel.
Setting this variable to enableFrontP… | scalar | Enumeration | .1.3.6.1.4.1.318.1.1.8.4.3 |
| atsConfigVoltageSensitivity mandatory This variable defines the sensitivity to changes in voltage:
high(1) for best protection, low(2) for frequent small line
voltage changes. | scalar | Enumeration | .1.3.6.1.4.1.318.1.1.8.4.4 |
| atsConfigTransferVoltageRange mandatory This variable defines the range of acceptable voltage from a power source.
If the voltage measured from the selected input source is not within this
range, the Automatic Transfer … | scalar | Enumeration | .1.3.6.1.4.1.318.1.1.8.4.5 |
| atsConfigCurrentLimit mandatory The threshold (in Amps) at which an Over Current Alarm will be generated.
This OID returns the overload threshold value of the
OID atsConfigPhaseOverLoadThreshold for the 1U ATS a… | scalar | Integer32 | .1.3.6.1.4.1.318.1.1.8.4.6 |
| atsConfigResetValues mandatory Resets the ATS configuration to its default values.
Returns (-1) if not supported. | scalar | Enumeration | .1.3.6.1.4.1.318.1.1.8.4.7 |
| atsConfigLineVRMS mandatory To configure the input RMS voltage. | scalar | Integer32 | .1.3.6.1.4.1.318.1.1.8.4.8 |
| atsConfigLineVRMSNarrowLimit mandatory To configure the Line VRMS Narrow Limit. | scalar | Integer32 | .1.3.6.1.4.1.318.1.1.8.4.9 |