modRx2CfgAgcMode
PPM-IGNIS-MIB ·
.1.3.6.1.4.1.31225.1.1.4.1.1.205
Object
column
r/w
Enumeration
Rx2 Automatic Gain Control (AGC) mode select. If in AGC RF Level mode, the AGC control loop will adjust the RF gain to maintain a constant RF power output If in AGC RLL (Received Light Level) mode, the receiver will attempt to compensate for the optical loss by adjusting the modules RF gain, and the AGC Target is not used (instead the SGC gain setting may be used to set a module gain target)
Context
- MIB
- PPM-IGNIS-MIB
- OID
.1.3.6.1.4.1.31225.1.1.4.1.1.205- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- slotsEntry
- Table
- slotsTable
- Siblings
- 212
Syntax
Enumeration
Values & Constraints
No enumerated values or constraints recorded.
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| modIx Module index in slots table. Corresponds to module slot in the ViaLiteHD chassis | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.1 |
| modMonPanelComp Module Front Panel type bitmap.
Encoded as two 4 bit nibbles (LSNibble for the lower(B) front panel port, MSNibble for the upper (A) front panel port).
Port type encoded as: Not F… | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.10 |
| modTx1InterRange Internal system information. | column | OctetString | .1.3.6.1.4.1.31225.1.1.4.1.1.100 |
| modTx1InterBiasSet Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.101 |
| modTx1InterPowerSet Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.102 |
| modTx1InterPowerCal Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.103 |
| modTx1InterGainDef Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.104 |
| modTx1InterRfMonCal Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.105 |
| modTx1InterFskFreqSet Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.106 |
| modTx1InterRfGainCal Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.107 |
| modTx1InterMonitorMask Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.108 |
| modTx1InterAlarmMask Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.109 |
| modMonPanelLEDS A bitmap representation of the module front panel LEDs.
Each LED is a 4 bit nibble, encoded as: Green=0x1, Red=0x3, Red&Flashing=0x7
Nibbles are arranged (LSB->MSB) PWR LED, ALM … | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.11 |
| modLabel Module type label. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.31225.1.1.4.1.1.12 |
| modTx2InterRange Internal system information. | column | OctetString | .1.3.6.1.4.1.31225.1.1.4.1.1.120 |
| modTx2InterBiasSet Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.121 |
| modTx2InterPowerSet Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.122 |
| modTx2InterPowerCal Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.123 |
| modTx2InterGainDef Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.124 |
| modTx2InterRfMonCal Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.125 |
| modTx2InterFskFreqSet Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.126 |
| modTx2InterRfGainCal Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.127 |
| modTx2InterMonitorMask Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.128 |
| modFreeText User defined module name. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.31225.1.1.4.1.1.13 |
| modFwDate Firmware build date | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.31225.1.1.4.1.1.14 |
| modRx1MonSuppVoltage Rx1 Current supply voltage measured in mV. | column | mV Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.140 |
| modRx1MonRLLBias Module Rx1 Photodiode received light level [0.01dBm]. | column | x 0.01dBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.141 |
| modRx1MonRfPower Module Rx1 current RF power [mdBm]. | column | mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.142 |
| modRx1MonRfGain Module Rx1 current RF gain [mdB]. | column | mdB Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.143 |
| modRx1MonStatus Bitmap encoding of the current configuration status of the Rx1 module.
Bit 0: FSK (Digital Channel) Detection Status (0=Not Detected, 1=Detected)
1: FSK (Digital Channel) Detecti… | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.144 |
| modRx1MonAlarms Bitmap encoding of the current alarm status of the Rx1 module. All bits are encoded as 0=NoAlarm 1=Alarm
Bit 0: Major Alarm
1: Minor Alarm
2: Automatic Gain Control (AGC) Alarm
… | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.145 |
| modRx1MonOutputPower Rx1 Current output RF power level, measured in 10mdBm | column | 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.146 |
| modWaveLenInteger Optical Wavelength (integer part). Given in nm (truncated) | column | nm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.15 |
| modWaveLenDecimal Optical Wavelength (decimal part). Given in 0.01nm | column | x 0.01nm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.16 |
| modRx2MonSuppVoltage Rx2 Current supply voltage measured value [mV]. | column | mV Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.160 |
| modRx2MonRLLBias Rx2 Photodiode received light level [0.01dBm]. | column | x 0.01dBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.161 |
| modRx2MonRfPower Rx2 Current RF power [mdBm]. | column | mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.162 |
| modRx2MonRfGain Rx2 Current RF gain [mdB]. | column | mdB Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.163 |
| modRx2MonStatus Bitmap encoding of the current configuration status of the Rx1 module.
Bit 0: FSK (Digital Channel) Detection Status (0=Not Detected, 1=Detected)
1: FSK (Digital Channel) Detecti… | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.164 |
| modRx2MonAlarms Bitmap encoding of the current alarm status of the Rx1 module. All bits are encoded as 0=NoAlarm 1=Alarm
Bit 0: Major Alarm
1: Minor Alarm
2: Automatic Gain Control (AGC) Alarm
… | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.165 |
| modRx2MonOutputPower Rx2 Current output RF power level, measured in 10mdBm | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.166 |
| modRx1CfgGainSoftSet Rx1 Software Gain Control (SGC) setting measured in 10mdB. | column | x 10mdB Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.180 |
| modRx1CfgAgcTarget Rx1 Automatic Gain Control target, measured in 10mdBm. | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.181 |
| modRx1CfgFskDisable Rx1 Digital Channel Frequency Shift Keying (FSK) enable/disable. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.182 |
| modRx1CfgAgc Rx1 Automatic Gain Control (AGC) enable/disable. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.183 |
| modRx1CfgSgc Rx1 Software Gain Control (SGC) enable/disable. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.184 |
| modRx1CfgAgcMode Rx1 Automatic Gain Control (AGC) mode select.
If in AGC RF Level mode, the AGC control loop will adjust the RF gain to maintain a constant RF power output
If in AGC RLL (Received … | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.185 |
| modRx1CfgGpsLoad Rx1 GPS dummy load enable/disable. If the module does not support GPS mode, this will have no effect. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.186 |
| modRx1CfgRFPlevelHigh Rx1 RF Power level alarm high threshold, measured in 10mdBm | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.187 |
| modRx1CfgRFPlevelLow Rx1 RF Power level alarm low threshold, measured in 10mdBm | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.188 |
| modType Module type. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.2 |
| modTx1MonSuppVoltage Tx1 Current supply voltage measured in mV. Nominal 12000mV | column | mV Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.20 |
| modRx2CfgGainSoftSet Rx2 Software Gain Control (SGC) level measured in 10mdB. | column | x 10mdB Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.200 |
| modRx2CfgAgcTarget Rx2 Automatic Gain Control (AGC) target, measured in 10mdBm. | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.201 |
| modRx2CfgFskDisable Rx2 Digital Channel Frequency Shift Keying (FSK) enable/disable. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.202 |
| modRx2CfgAgc Rx2 Automatic Gain Control (AGC) enable/disable. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.203 |
| modRx2CfgSgc Rx2 Software Gain Control (SGC) enable/disable. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.204 |
| modRx2CfgGpsLoad Rx2 GPS dummy load enable/disable. If the module does not support GPS mode, this will have no effect. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.206 |
| modRx2CfgRFPlevelHigh Rx2 RF Power level alarm high threshold, measured in 10mdBm | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.207 |
| modRx2CfgRFPlevelLow Rx2 RF Power level alarm low threshold, measured in 10mdBm | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.208 |
| modTx1MonLaserBias Tx1 Current laser bias current measurement, measured in uA. | column | uA Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.21 |
| modTx1MonLaserPower Tx1 Current laser power measurement, measured in 10mdBm. | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.22 |
| modRx1InterRange Internal system information. | column | OctetString | .1.3.6.1.4.1.31225.1.1.4.1.1.220 |
| modRx1InterBiasSet Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.221 |
| modRx1InterGainDef Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.222 |
| modRx1InterRfMonCal Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.223 |
| modRx1InterFskFreqSet Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.224 |
| modRx1InterFskSlicSet Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.225 |
| modRx1InterRfGainCal Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.226 |
| modRx1InterMonitorMask Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.227 |
| modRx1InterAlarmMask Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.228 |
| modTx1MonRfPower Tx1 Current RF power, measured in 10mdBm. | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.23 |
| modTx1MonRfGain Tx1 Current RF gain, measured in 10mdB. | column | x 10mdB Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.24 |
| modRx2InterRange Internal system information. | column | OctetString | .1.3.6.1.4.1.31225.1.1.4.1.1.240 |
| modRx2InterBiasSet Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.241 |
| modRx2InterGainDef Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.242 |
| modRx2InterRfMonCal Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.243 |
| modRx2InterFskFreqSet Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.244 |
| modRx2InterFskSlicSet Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.245 |
| modRx2InterRfGainCal Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.246 |
| modRx2InterMonitorMask Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.247 |
| modRx2InterAlarmMask Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.248 |
| modTx1MonFeedI Tx1 External feed current [0.1mA]. | column | x 0.1mA Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.25 |
| modTx1MonFeedV Tx1 External feed voltage [mV]. | column | mV Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.26 |
| modAmpMonVcc Amplifier supply voltage, measured in mV. | column | mV Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.260 |
| modAmpMonTemp Amplifier temperature, measured in degrees Celsius | column | degC Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.261 |
| modAmp1MonRf Amplifier 1 Current RF level, measured in 10mdBm. | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.262 |
| modAmp1MonRfGain Amplifier 1 RF gain, measured in 10mdB. | column | x 10mdB Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.263 |
| modAmp1MonStatus Bitmap encoding of the current configuration status of the Amplifier card:
Bit 0: Amplifier 2 Automatic Gain Control (AGC) Status (0=Disabled, 1=Enabled)
1: Amplifier 1 Automatic… | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.264 |
| modAmp1MonAlarms Bitmap encoding of the current alarm status of the amplifier card: (All alarms encoded as 0=NoAlarm, 1=Alarm)
Bit 0: Amplifier 2 RF Gain Alarm
1: Amplifier 2 RF Level Alarm
2: T… | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.265 |
| modTx1MonStatus Bitmap encoding of the current configuration status of the Tx1 module.
Bit 0: Laser Status (0=Enabled, 1=Disabled)
1: FSK Tone (Digital Channel) Status (0=Enabled, 1=Disabled)
2… | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.27 |
| modTx1MonAlarms Bitmap encoding of the current alarm status of the Tx1 module. All bits are encoded as 0=NoAlarm 1=Alarm
Bit 0: Major Alarm
1: Minor Alarm
2: Laser Alarm
3: Automatic Gain Cont… | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.28 |
| modAmp2MonRf Amplifier 2 Current RF level, measured in 10mdBm. | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.280 |
| modAmp2MonRfGain Amplifier 2 RF gain, measured in 10mdBm. | column | x 10mdB Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.281 |
| modAmp2MonStatus Bitmap encoding of the current configuration status of the Amplifier card:
Bit 0: Amplifier 1 Automatic Gain Control (AGC) Status (0=Disabled, 1=Enabled)
1: Amplifier 2 Automatic… | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.282 |
| modAmp2MonAlarms Bitmap encoding of the current alarm status of the amplifier card: (All alarms encoded as 0=NoAlarm, 1=Alarm)
Bit 0: Amplifier 2 RF Gain Alarm
1: Amplifier 2 RF Level Alarm
2: T… | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.283 |
| modTx1MonInputPower Tx1 Input power level, measured in 10mdBm | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.29 |
| modPN Module part number. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.31225.1.1.4.1.1.3 |
| modTx1MonTECTemprtr Tx1 Laser TEC (Thermo-Electric Cooler) temperature, measured in degrees Centigrade. | column | degC Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.30 |
| modAmp1CfgGainSoftSet Amp 1 Software Gain Control (SGC) gain setting, measured in 10mdB | column | x 10mdB Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.300 |
| modAmp1CfgAgcTarget Amp 1 Automatic Gain Control (AGC) target, measured in 10mdBm. | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.301 |
| modAmp1InterRange Internal system information. | column | OctetString | .1.3.6.1.4.1.31225.1.1.4.1.1.302 |
| modAmp1InterGainCal Amp 1 Gain calibration. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.303 |
| modAmp1InterRfMonCal Amp 1 RF level monitor calibration. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.304 |
| modAmp1InterAgcCtrl Amp 1 Automatic Gain Control setting. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.305 |
| modTx1MonTEC Tx1 Laser TEC (Thermo-Electric Cooler) current, measured in 0.1mA | column | x 0.1mA Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.31 |
| modAmp2CfgGainSoftSet Amp 1 Software Gain Control (SGC) gain setting, measured in 10mdB | column | x 10mdB Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.320 |
| modAmp2CfgAgcTarget Amp 2 Automatic Gain Control (AGC) target, measured in 10mdBm. | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.321 |
| modAmp2InterRange Internal system information. | column | OctetString | .1.3.6.1.4.1.31225.1.1.4.1.1.322 |
| modAmp2InterGainCal Amp 2 Gain calibration. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.323 |
| modAmp2InterRfMonCal Amp 2 RF level monitor calibration. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.324 |
| modAmp2InterAgcCtrl Amp 2 Automatic Gain Control enable/disable. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.325 |
| modAmp1LvlLimitHCtrl Amp 1 RF Level high alarm threshold, measured in 10mdBm. | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.330 |
| modAmp1LvlLimitLCtrl Amp 1 RF Level low alarm threshold, measured in 10mdBm. | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.331 |
| modAmp2LvlLimitHCtrl Amp 2 RF Level high alarm threshold, measured in 10mdBm. | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.332 |
| modAmp2LvlLimitLCtrl Amp 2 RF Level low alarm threshold, measured in 10mdBm. | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.333 |
| modAmpGainAlThCtrl Amplifier Gain warning threshold, measured in 10mdB.
This threshold is measured from the alarm thresholds (typically a low threshold of 15dB, and a high threshold of 30dB),
i.e, i… | column | x 10mdB Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.334 |
| modAmpLvlAlThCtrl Amplifier RF Level warning threshold, measured in 10mdBm.
This threshold is measured from the alarm threshold,
i.e, if the Alarm threshold is 10dBm, and this warning threshold is … | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.335 |
| modSwtchMonModeSetting Switch mode status. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.350 |
| modSwtchMonStatus Bitmap encoding of the current switch status.
Bit 0-3: Unused
4: Switch Direction (1=Left, 0=Right)
5-11: Unused
12-13: Front Panel ALM LED status (00=off, 01=Green, 11=Red)
1… | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.351 |
| modSWAlarmBitMap Bitmap encoding of the current switch alarm status.
Bit 0-1: Unused
2: Minor Alarm
3: Major Alarm
4-15: Unused | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.352 |
| modSwtchModeSetting Switch mode control | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.355 |
| modLNBAlarmMask LNB masking for invalid alarms. Bit 0 = major, Bit 8= OLF | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.360 |
| modLNBbitAUX LNB Auxillary Mode setting: ON = Set Vout to +22V nominal. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.361 |
| modLNBbitITEST LNB Current threshold setting. Options are Low (6mA) or High (12mA) | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.362 |
| modLNBbitEN LNB Module Power block enable. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.363 |
| modLNBbitVSEL LNB Module Output voltage select. Options are High (18V nominal), or Low (13V Nominal). | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.364 |
| modLNBbitLLC LNB Cable compensation setting. If enabled, the output voltage is boosted by an additional +1V. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.365 |
| modLNBbitTEN LNB 22kHz tone enable. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.366 |
| modLNBbitTTX LNB 22kHz tone output switch. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.367 |
| modLNBbitPCL LNB Current limit mode selector.
Static mode uses a simple clamp current limit.
Active mode uses a pulsed current limit | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.368 |
| modLNBbitOLF LNB Overload flag. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.369 |
| modLNBbitOTF LNB Over Temperature flag. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.370 |
| modLNBMonStatus Bitmap of the current status of the LNB module
Bit 0: Power Block Enable (0=Disabled, 1=Enabled)
1: Output Voltage Setting (0=Low(13V), 1=High(18V))
2: Cable Compensation settin… | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.371 |
| modLNBDIPSwitch Bitmap of the DIP switch settings on the LNB Module. All bits are encoded as 0=disabled, 1=enabled
Bit 0: Power Block Enable
1: High Voltage output
2: Tone
3: Cable Compensatio… | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.372 |
| modLNBAlarmStatus Bitmap of the LNB alarm status. All bits are encoded as 0=noAlarm, 1= Alarm.
Bit 0: Overload Alarm
1: Over Temperature Alarm
2-7: Unused
8: Major Alarm
9: Mino… | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.373 |
| modETHMonSupplyVolt Ethernet module supply voltage, measured in mV | column | mV Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.380 |
| modETHMonLinkdataRate Ethernet module Fibre Link data rate bitmap. All bits are encoded as 0=noLink, 1=Link).
Bit 0-4: Unused
5: Valid 100BASE Link
6: Valid 1000BASE Link
7: Valid Link (any speed) | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.381 |
| modETHMonDataActivity Ethernet data activity bitmap.
Bit 0-2: Unused
3: Activity (0=noActivity, 1=Activity)
4-7: Unused | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.382 |
| modETHMonAlarms Ethernet module alarms bitmap. All bits are encoded as 0=noAlarm, 1=Alarm
Bit 0-1: Unused
2: Minor Alarm
3: Major Alarm
4-7: Unused | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.383 |
| modETHMonCopperdataRate Ethernet module Copper Link data rate bitmap. All bits are encoded as 0=noLink, 1=Link).
Bit 0-3: Unused
4: Valid 10BASE link
5: Valid 100BASE Link
6: Valid 1000BASE Link
7: V… | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.384 |
| modETHMonCopperActivity Ethernet module Copper Link activity bitmap.
Bit 0: Unused
1: Duplex (0=Half Duplex, 1=Full Duplex)
2: Collision (0=noCollision, 1=Collision Detected)
3: Activity (0=noActivity… | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.385 |
| modSERMonLinkdataRate Serial data module link data rate. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.390 |
| modSERMonDataActivity Serial data module data activity. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.391 |
| modSERMonSerialAlarm Serial data alarm bitmap. All bits are encoded as 0=noAlarm, 1=Alarm.
Bit 0: Vcc Alarm
1: Laser Power Alarm
2: RLL (Received Light Level) Alarm
3: Temperature Alarm
4-7: Unuse… | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.392 |
| modSERMonChannel1Type Serial data - Channel 1 type. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.393 |
| modSERMonChannel2 Serial data - Channel 2 type. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.394 |
| modSERMonSupplyVolt Serial data - Supply voltage. | column | mV Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.395 |
| modSERMonLaserPower Serial Digital Module Laser optical power [10mdBm]. | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.396 |
| modSERMonRLLLevel Serial Digital Module RLL level [10mdBm]. | column | x 10mDBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.397 |
| modSERMonDipManualMode Serial Digital Module Manual Mode DIP switch status. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.398 |
| modFWPN Module firmware part number. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.31225.1.1.4.1.1.4 |
| modTx2MonSuppVoltage Tx2 Current supply voltage measured in mV. | column | mV Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.40 |
| modTx2MonLaserBias Tx2 Current laser bias current measurement [uA]. | column | uA Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.41 |
| modTx2MonLaserPower Tx2 Current laser power measurement, measured in 10mdBm. | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.42 |
| modSERCfgChannelRate Serial Digital Module channel data rate setting. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.420 |
| modSERCfgTTlImpedance Serial Digital Module TTL Impedance setting. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.421 |
| modSERCfgLaserDisable Serial Digital Module Laser enable/disable. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.422 |
| modPROCDescription PROC module description. | column | OctetString | .1.3.6.1.4.1.31225.1.1.4.1.1.423 |
| modTx2MonRfPower Tx2 Current RF power, measured in 10mdBm. | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.43 |
| modMaintenanceMode Module Maintenance Mode.
When in maintenance mode, a module will not produce events/traps and will not contribute to the summary alarm outputs.
Other module OIDs will be updated a… | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.430 |
| modTx2MonRfGain Tx2 Current RF gain, measured in 10mdB. | column | x 10mdB Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.44 |
| modG6CardMonSupplyVolt Card supply voltage, measured in mV. | column | mV Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.440 |
| modTx2MonFeedI Tx2 External feed current [0.1mA]. | column | 0.1mA Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.45 |
| modG6Dev1CfgBiasTSrc Set bias-t source. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.452 |
| modG6Dev1MonFeedI External feed current [0.01mA]. | column | x 0.01mA Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.454 |
| modG6Dev1MonFeedV External feed voltage [mV]. | column | mV Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.455 |
| modG6Dev1Type RF device 1 type. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.456 |
| modG6Dev1WaveLenInteger Optical Wavelength (integer part). Given in nm (truncated) | column | nm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.457 |
| modG6Dev1WaveLenDecimal Optical Wavelength (decimal part). Given in 0.01nm | column | x 0.01nm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.458 |
| modTx2MonFeedV Tx2 External feed voltage [mV]. | column | mV Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.46 |
| modG6Dev1CfgAFDThr Antenna fault detection low current threshold | column | x 0.01mA Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.464 |
| modG6Dev1CfgAFDEn Antenna fault detection enable | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.465 |
| modG6Dev1CfgAGCMode Enable automatic gain control based on received light level (RLL) | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.466 |
| modTx2MonStatus Bitmap encoding of the current configuration status of the Tx2 module.
Bit 0: Laser Status (0=Enabled, 1=Disabled)
1: FSK Tone (Digital Channel) Status (0=Enabled, 1=Disabled)
2… | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.47 |
| modG6Dev2CfgBiasTSrc Set bias-t source. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.472 |
| modG6Dev2MonFeedI External feed current [0.01mA]. | column | x 0.01mA Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.474 |
| modG6Dev2MonFeedV External feed voltage [mV]. | column | mV Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.475 |
| modG6Dev2Type RF device 2 type. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.476 |
| modG6Dev2WaveLenInteger Optical Wavelength (integer part). Given in nm (truncated) | column | nm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.477 |
| modG6Dev2WaveLenDecimal Optical Wavelength (decimal part). Given in 0.01nm | column | x 0.01nm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.478 |
| modTx2MonAlarms Bitmap encoding of the current alarm status of the Tx2 module. All bits are encoded as 0=NoAlarm 1=Alarm
Bit 0: Major Alarm
1: Minor Alarm
2: Laser Alarm
3: Automatic Gain Cont… | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.48 |
| modG6Dev2CfgAFDThr Antenna fault detection low current threshold | column | x 0.01mA Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.484 |
| modG6Dev2CfgAFDEn Antenna fault detection enable | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.485 |
| modG6Dev2CfgAGCMode Enable automatic gain control based on received light level (RLL) | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.486 |
| modTx2MonInputPower Tx2 Input power level, measured in 10mdBm | column | x 10mdB Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.49 |
| modFWVer Module firmware version and build date/time. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.31225.1.1.4.1.1.5 |
| modSN Module serial number. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.31225.1.1.4.1.1.6 |
| modTx1CfgGainSoftSet Tx1 Software Gain Control (SGC) Gain setting, measured in 10mdB | column | x 10mdB Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.60 |
| modTx1CfgAgcTarget Tx1 Automatic Gain Control target, measured in 10mdBm. | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.61 |
| modTx1CfgLaserDisable Module Tx1 Laser enable/disable. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.62 |
| modTx1CfgFskDisable Module Tx1 FSK Tone (Digital Channel) Enable/disable. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.63 |
| modTx1CfgAgc Module Tx1 Automatic Gain Control enable/disable. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.64 |
| modTx1CfgSgc Module Tx1 Software Gain Control enable/disable. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.65 |
| modTx1CfgGpsLoad Tx1 GPS dummy load enable/disable. If the module does not support GPS mode, this will have no effect. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.66 |
| modTx1CfgRFPlevelHigh Tx1 Rf Power level alarm high threshold, measured in 10mdBm. | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.67 |
| modTx1CfgRFPlevelLow Tx1 Rf Power level alarm low threshold, measured in 10mdBm. | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.68 |
| modTx1CfgLnbAlarm Tx1 LNB voltage alarm severity. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.69 |
| modOemNumber Module OEM number. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.31225.1.1.4.1.1.7 |
| modTx1CfgTECcontrol deprecated Module Tx1 TEC control enable/disable. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.70 |
| modCustomerID Module customer ID. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.31225.1.1.4.1.1.8 |
| modTx2CfgGainSoftSet Tx2 Software Gain Control (SGC) Gain setting, measured in 10mdB | column | x 10mdB Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.80 |
| modTx2CfgAgcTarget Tx2 Automatic Gain Control (AGC) target, measured in 10mdBm. | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.81 |
| modTx2CfgLaserDisable Module Tx2 Laser enable/disable. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.82 |
| modTx2CfgFskDisable Module Tx2 FSK Tone (Digital Channel) Enable/disable. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.83 |
| modTx2CfgAgc Module Tx2 Automatic Gain Control (AGC) enable/disable. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.84 |
| modTx2CfgSgc Module Tx2 Software Gain Control (SGC) enable/disable. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.85 |
| modTx2CfgGpsLoad Module Tx2 GPS dummy load enable/disable. If the module does not support GPS mode, this will have no effect. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.86 |
| modTx2CfgRFPlevelHigh Tx2 Rf Power level alarm high threshold, measured in 10mdBm. | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.87 |
| modTx2CfgRFPlevelLow Tx2 RF Power level alarm low threshold, measured in 10mdBm. | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.88 |
| modTx2CfgLnbAlarm Module Tx2 LNB voltage alarm severity. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.89 |
| modMonLifeCounter Module working hours counter. Increments every 2 hours of continuous operation. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.9 |