modRx1CfgGpsLoad
PPM-IGNIS-MIB ·
.1.3.6.1.4.1.31225.1.1.4.1.1.186
Object
column
r/w
Enumeration
Rx1 GPS dummy load enable/disable. If the module does not support GPS mode, this will have no effect.
Context
- MIB
- PPM-IGNIS-MIB
- OID
.1.3.6.1.4.1.31225.1.1.4.1.1.186- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- slotsEntry
- Table
- slotsTable
- Siblings
- 212
Syntax
Enumeration
Values & Constraints
No enumerated values or constraints recorded.
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| modIx Module index in slots table. Corresponds to module slot in the ViaLiteHD chassis | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.1 |
| modMonPanelComp Module Front Panel type bitmap.
Encoded as two 4 bit nibbles (LSNibble for the lower(B) front panel port, MSNibble for the upper (A) front panel port).
Port type encoded as: Not F… | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.10 |
| modTx1InterRange Internal system information. | column | OctetString | .1.3.6.1.4.1.31225.1.1.4.1.1.100 |
| modTx1InterBiasSet Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.101 |
| modTx1InterPowerSet Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.102 |
| modTx1InterPowerCal Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.103 |
| modTx1InterGainDef Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.104 |
| modTx1InterRfMonCal Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.105 |
| modTx1InterFskFreqSet Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.106 |
| modTx1InterRfGainCal Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.107 |
| modTx1InterMonitorMask Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.108 |
| modTx1InterAlarmMask Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.109 |
| modMonPanelLEDS A bitmap representation of the module front panel LEDs.
Each LED is a 4 bit nibble, encoded as: Green=0x1, Red=0x3, Red&Flashing=0x7
Nibbles are arranged (LSB->MSB) PWR LED, ALM … | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.11 |
| modLabel Module type label. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.31225.1.1.4.1.1.12 |
| modTx2InterRange Internal system information. | column | OctetString | .1.3.6.1.4.1.31225.1.1.4.1.1.120 |
| modTx2InterBiasSet Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.121 |
| modTx2InterPowerSet Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.122 |
| modTx2InterPowerCal Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.123 |
| modTx2InterGainDef Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.124 |
| modTx2InterRfMonCal Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.125 |
| modTx2InterFskFreqSet Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.126 |
| modTx2InterRfGainCal Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.127 |
| modTx2InterMonitorMask Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.128 |
| modFreeText User defined module name. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.31225.1.1.4.1.1.13 |
| modFwDate Firmware build date | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.31225.1.1.4.1.1.14 |
| modRx1MonSuppVoltage Rx1 Current supply voltage measured in mV. | column | mV Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.140 |
| modRx1MonRLLBias Module Rx1 Photodiode received light level [0.01dBm]. | column | x 0.01dBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.141 |
| modRx1MonRfPower Module Rx1 current RF power [mdBm]. | column | mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.142 |
| modRx1MonRfGain Module Rx1 current RF gain [mdB]. | column | mdB Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.143 |
| modRx1MonStatus Bitmap encoding of the current configuration status of the Rx1 module.
Bit 0: FSK (Digital Channel) Detection Status (0=Not Detected, 1=Detected)
1: FSK (Digital Channel) Detecti… | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.144 |
| modRx1MonAlarms Bitmap encoding of the current alarm status of the Rx1 module. All bits are encoded as 0=NoAlarm 1=Alarm
Bit 0: Major Alarm
1: Minor Alarm
2: Automatic Gain Control (AGC) Alarm
… | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.145 |
| modRx1MonOutputPower Rx1 Current output RF power level, measured in 10mdBm | column | 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.146 |
| modWaveLenInteger Optical Wavelength (integer part). Given in nm (truncated) | column | nm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.15 |
| modWaveLenDecimal Optical Wavelength (decimal part). Given in 0.01nm | column | x 0.01nm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.16 |
| modRx2MonSuppVoltage Rx2 Current supply voltage measured value [mV]. | column | mV Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.160 |
| modRx2MonRLLBias Rx2 Photodiode received light level [0.01dBm]. | column | x 0.01dBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.161 |
| modRx2MonRfPower Rx2 Current RF power [mdBm]. | column | mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.162 |
| modRx2MonRfGain Rx2 Current RF gain [mdB]. | column | mdB Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.163 |
| modRx2MonStatus Bitmap encoding of the current configuration status of the Rx1 module.
Bit 0: FSK (Digital Channel) Detection Status (0=Not Detected, 1=Detected)
1: FSK (Digital Channel) Detecti… | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.164 |
| modRx2MonAlarms Bitmap encoding of the current alarm status of the Rx1 module. All bits are encoded as 0=NoAlarm 1=Alarm
Bit 0: Major Alarm
1: Minor Alarm
2: Automatic Gain Control (AGC) Alarm
… | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.165 |
| modRx2MonOutputPower Rx2 Current output RF power level, measured in 10mdBm | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.166 |
| modRx1CfgGainSoftSet Rx1 Software Gain Control (SGC) setting measured in 10mdB. | column | x 10mdB Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.180 |
| modRx1CfgAgcTarget Rx1 Automatic Gain Control target, measured in 10mdBm. | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.181 |
| modRx1CfgFskDisable Rx1 Digital Channel Frequency Shift Keying (FSK) enable/disable. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.182 |
| modRx1CfgAgc Rx1 Automatic Gain Control (AGC) enable/disable. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.183 |
| modRx1CfgSgc Rx1 Software Gain Control (SGC) enable/disable. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.184 |
| modRx1CfgAgcMode Rx1 Automatic Gain Control (AGC) mode select.
If in AGC RF Level mode, the AGC control loop will adjust the RF gain to maintain a constant RF power output
If in AGC RLL (Received … | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.185 |
| modRx1CfgRFPlevelHigh Rx1 RF Power level alarm high threshold, measured in 10mdBm | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.187 |
| modRx1CfgRFPlevelLow Rx1 RF Power level alarm low threshold, measured in 10mdBm | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.188 |
| modType Module type. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.2 |
| modTx1MonSuppVoltage Tx1 Current supply voltage measured in mV. Nominal 12000mV | column | mV Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.20 |
| modRx2CfgGainSoftSet Rx2 Software Gain Control (SGC) level measured in 10mdB. | column | x 10mdB Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.200 |
| modRx2CfgAgcTarget Rx2 Automatic Gain Control (AGC) target, measured in 10mdBm. | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.201 |
| modRx2CfgFskDisable Rx2 Digital Channel Frequency Shift Keying (FSK) enable/disable. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.202 |
| modRx2CfgAgc Rx2 Automatic Gain Control (AGC) enable/disable. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.203 |
| modRx2CfgSgc Rx2 Software Gain Control (SGC) enable/disable. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.204 |
| modRx2CfgAgcMode Rx2 Automatic Gain Control (AGC) mode select.
If in AGC RF Level mode, the AGC control loop will adjust the RF gain to maintain a constant RF power output
If in AGC RLL (Received … | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.205 |
| modRx2CfgGpsLoad Rx2 GPS dummy load enable/disable. If the module does not support GPS mode, this will have no effect. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.206 |
| modRx2CfgRFPlevelHigh Rx2 RF Power level alarm high threshold, measured in 10mdBm | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.207 |
| modRx2CfgRFPlevelLow Rx2 RF Power level alarm low threshold, measured in 10mdBm | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.208 |
| modTx1MonLaserBias Tx1 Current laser bias current measurement, measured in uA. | column | uA Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.21 |
| modTx1MonLaserPower Tx1 Current laser power measurement, measured in 10mdBm. | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.22 |
| modRx1InterRange Internal system information. | column | OctetString | .1.3.6.1.4.1.31225.1.1.4.1.1.220 |
| modRx1InterBiasSet Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.221 |
| modRx1InterGainDef Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.222 |
| modRx1InterRfMonCal Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.223 |
| modRx1InterFskFreqSet Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.224 |
| modRx1InterFskSlicSet Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.225 |
| modRx1InterRfGainCal Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.226 |
| modRx1InterMonitorMask Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.227 |
| modRx1InterAlarmMask Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.228 |
| modTx1MonRfPower Tx1 Current RF power, measured in 10mdBm. | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.23 |
| modTx1MonRfGain Tx1 Current RF gain, measured in 10mdB. | column | x 10mdB Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.24 |
| modRx2InterRange Internal system information. | column | OctetString | .1.3.6.1.4.1.31225.1.1.4.1.1.240 |
| modRx2InterBiasSet Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.241 |
| modRx2InterGainDef Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.242 |
| modRx2InterRfMonCal Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.243 |
| modRx2InterFskFreqSet Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.244 |
| modRx2InterFskSlicSet Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.245 |
| modRx2InterRfGainCal Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.246 |
| modRx2InterMonitorMask Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.247 |
| modRx2InterAlarmMask Internal system information. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.248 |
| modTx1MonFeedI Tx1 External feed current [0.1mA]. | column | x 0.1mA Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.25 |
| modTx1MonFeedV Tx1 External feed voltage [mV]. | column | mV Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.26 |
| modAmpMonVcc Amplifier supply voltage, measured in mV. | column | mV Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.260 |
| modAmpMonTemp Amplifier temperature, measured in degrees Celsius | column | degC Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.261 |
| modAmp1MonRf Amplifier 1 Current RF level, measured in 10mdBm. | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.262 |
| modAmp1MonRfGain Amplifier 1 RF gain, measured in 10mdB. | column | x 10mdB Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.263 |
| modAmp1MonStatus Bitmap encoding of the current configuration status of the Amplifier card:
Bit 0: Amplifier 2 Automatic Gain Control (AGC) Status (0=Disabled, 1=Enabled)
1: Amplifier 1 Automatic… | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.264 |
| modAmp1MonAlarms Bitmap encoding of the current alarm status of the amplifier card: (All alarms encoded as 0=NoAlarm, 1=Alarm)
Bit 0: Amplifier 2 RF Gain Alarm
1: Amplifier 2 RF Level Alarm
2: T… | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.265 |
| modTx1MonStatus Bitmap encoding of the current configuration status of the Tx1 module.
Bit 0: Laser Status (0=Enabled, 1=Disabled)
1: FSK Tone (Digital Channel) Status (0=Enabled, 1=Disabled)
2… | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.27 |
| modTx1MonAlarms Bitmap encoding of the current alarm status of the Tx1 module. All bits are encoded as 0=NoAlarm 1=Alarm
Bit 0: Major Alarm
1: Minor Alarm
2: Laser Alarm
3: Automatic Gain Cont… | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.28 |
| modAmp2MonRf Amplifier 2 Current RF level, measured in 10mdBm. | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.280 |
| modAmp2MonRfGain Amplifier 2 RF gain, measured in 10mdBm. | column | x 10mdB Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.281 |
| modAmp2MonStatus Bitmap encoding of the current configuration status of the Amplifier card:
Bit 0: Amplifier 1 Automatic Gain Control (AGC) Status (0=Disabled, 1=Enabled)
1: Amplifier 2 Automatic… | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.282 |
| modAmp2MonAlarms Bitmap encoding of the current alarm status of the amplifier card: (All alarms encoded as 0=NoAlarm, 1=Alarm)
Bit 0: Amplifier 2 RF Gain Alarm
1: Amplifier 2 RF Level Alarm
2: T… | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.283 |
| modTx1MonInputPower Tx1 Input power level, measured in 10mdBm | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.29 |
| modPN Module part number. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.31225.1.1.4.1.1.3 |
| modTx1MonTECTemprtr Tx1 Laser TEC (Thermo-Electric Cooler) temperature, measured in degrees Centigrade. | column | degC Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.30 |
| modAmp1CfgGainSoftSet Amp 1 Software Gain Control (SGC) gain setting, measured in 10mdB | column | x 10mdB Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.300 |
| modAmp1CfgAgcTarget Amp 1 Automatic Gain Control (AGC) target, measured in 10mdBm. | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.301 |
| modAmp1InterRange Internal system information. | column | OctetString | .1.3.6.1.4.1.31225.1.1.4.1.1.302 |
| modAmp1InterGainCal Amp 1 Gain calibration. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.303 |
| modAmp1InterRfMonCal Amp 1 RF level monitor calibration. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.304 |
| modAmp1InterAgcCtrl Amp 1 Automatic Gain Control setting. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.305 |
| modTx1MonTEC Tx1 Laser TEC (Thermo-Electric Cooler) current, measured in 0.1mA | column | x 0.1mA Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.31 |
| modAmp2CfgGainSoftSet Amp 1 Software Gain Control (SGC) gain setting, measured in 10mdB | column | x 10mdB Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.320 |
| modAmp2CfgAgcTarget Amp 2 Automatic Gain Control (AGC) target, measured in 10mdBm. | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.321 |
| modAmp2InterRange Internal system information. | column | OctetString | .1.3.6.1.4.1.31225.1.1.4.1.1.322 |
| modAmp2InterGainCal Amp 2 Gain calibration. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.323 |
| modAmp2InterRfMonCal Amp 2 RF level monitor calibration. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.324 |
| modAmp2InterAgcCtrl Amp 2 Automatic Gain Control enable/disable. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.325 |
| modAmp1LvlLimitHCtrl Amp 1 RF Level high alarm threshold, measured in 10mdBm. | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.330 |
| modAmp1LvlLimitLCtrl Amp 1 RF Level low alarm threshold, measured in 10mdBm. | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.331 |
| modAmp2LvlLimitHCtrl Amp 2 RF Level high alarm threshold, measured in 10mdBm. | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.332 |
| modAmp2LvlLimitLCtrl Amp 2 RF Level low alarm threshold, measured in 10mdBm. | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.333 |
| modAmpGainAlThCtrl Amplifier Gain warning threshold, measured in 10mdB.
This threshold is measured from the alarm thresholds (typically a low threshold of 15dB, and a high threshold of 30dB),
i.e, i… | column | x 10mdB Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.334 |
| modAmpLvlAlThCtrl Amplifier RF Level warning threshold, measured in 10mdBm.
This threshold is measured from the alarm threshold,
i.e, if the Alarm threshold is 10dBm, and this warning threshold is … | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.335 |
| modSwtchMonModeSetting Switch mode status. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.350 |
| modSwtchMonStatus Bitmap encoding of the current switch status.
Bit 0-3: Unused
4: Switch Direction (1=Left, 0=Right)
5-11: Unused
12-13: Front Panel ALM LED status (00=off, 01=Green, 11=Red)
1… | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.351 |
| modSWAlarmBitMap Bitmap encoding of the current switch alarm status.
Bit 0-1: Unused
2: Minor Alarm
3: Major Alarm
4-15: Unused | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.352 |
| modSwtchModeSetting Switch mode control | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.355 |
| modLNBAlarmMask LNB masking for invalid alarms. Bit 0 = major, Bit 8= OLF | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.360 |
| modLNBbitAUX LNB Auxillary Mode setting: ON = Set Vout to +22V nominal. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.361 |
| modLNBbitITEST LNB Current threshold setting. Options are Low (6mA) or High (12mA) | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.362 |
| modLNBbitEN LNB Module Power block enable. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.363 |
| modLNBbitVSEL LNB Module Output voltage select. Options are High (18V nominal), or Low (13V Nominal). | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.364 |
| modLNBbitLLC LNB Cable compensation setting. If enabled, the output voltage is boosted by an additional +1V. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.365 |
| modLNBbitTEN LNB 22kHz tone enable. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.366 |
| modLNBbitTTX LNB 22kHz tone output switch. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.367 |
| modLNBbitPCL LNB Current limit mode selector.
Static mode uses a simple clamp current limit.
Active mode uses a pulsed current limit | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.368 |
| modLNBbitOLF LNB Overload flag. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.369 |
| modLNBbitOTF LNB Over Temperature flag. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.370 |
| modLNBMonStatus Bitmap of the current status of the LNB module
Bit 0: Power Block Enable (0=Disabled, 1=Enabled)
1: Output Voltage Setting (0=Low(13V), 1=High(18V))
2: Cable Compensation settin… | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.371 |
| modLNBDIPSwitch Bitmap of the DIP switch settings on the LNB Module. All bits are encoded as 0=disabled, 1=enabled
Bit 0: Power Block Enable
1: High Voltage output
2: Tone
3: Cable Compensatio… | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.372 |
| modLNBAlarmStatus Bitmap of the LNB alarm status. All bits are encoded as 0=noAlarm, 1= Alarm.
Bit 0: Overload Alarm
1: Over Temperature Alarm
2-7: Unused
8: Major Alarm
9: Mino… | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.373 |
| modETHMonSupplyVolt Ethernet module supply voltage, measured in mV | column | mV Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.380 |
| modETHMonLinkdataRate Ethernet module Fibre Link data rate bitmap. All bits are encoded as 0=noLink, 1=Link).
Bit 0-4: Unused
5: Valid 100BASE Link
6: Valid 1000BASE Link
7: Valid Link (any speed) | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.381 |
| modETHMonDataActivity Ethernet data activity bitmap.
Bit 0-2: Unused
3: Activity (0=noActivity, 1=Activity)
4-7: Unused | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.382 |
| modETHMonAlarms Ethernet module alarms bitmap. All bits are encoded as 0=noAlarm, 1=Alarm
Bit 0-1: Unused
2: Minor Alarm
3: Major Alarm
4-7: Unused | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.383 |
| modETHMonCopperdataRate Ethernet module Copper Link data rate bitmap. All bits are encoded as 0=noLink, 1=Link).
Bit 0-3: Unused
4: Valid 10BASE link
5: Valid 100BASE Link
6: Valid 1000BASE Link
7: V… | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.384 |
| modETHMonCopperActivity Ethernet module Copper Link activity bitmap.
Bit 0: Unused
1: Duplex (0=Half Duplex, 1=Full Duplex)
2: Collision (0=noCollision, 1=Collision Detected)
3: Activity (0=noActivity… | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.385 |
| modSERMonLinkdataRate Serial data module link data rate. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.390 |
| modSERMonDataActivity Serial data module data activity. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.391 |
| modSERMonSerialAlarm Serial data alarm bitmap. All bits are encoded as 0=noAlarm, 1=Alarm.
Bit 0: Vcc Alarm
1: Laser Power Alarm
2: RLL (Received Light Level) Alarm
3: Temperature Alarm
4-7: Unuse… | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.392 |
| modSERMonChannel1Type Serial data - Channel 1 type. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.393 |
| modSERMonChannel2 Serial data - Channel 2 type. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.394 |
| modSERMonSupplyVolt Serial data - Supply voltage. | column | mV Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.395 |
| modSERMonLaserPower Serial Digital Module Laser optical power [10mdBm]. | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.396 |
| modSERMonRLLLevel Serial Digital Module RLL level [10mdBm]. | column | x 10mDBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.397 |
| modSERMonDipManualMode Serial Digital Module Manual Mode DIP switch status. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.398 |
| modFWPN Module firmware part number. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.31225.1.1.4.1.1.4 |
| modTx2MonSuppVoltage Tx2 Current supply voltage measured in mV. | column | mV Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.40 |
| modTx2MonLaserBias Tx2 Current laser bias current measurement [uA]. | column | uA Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.41 |
| modTx2MonLaserPower Tx2 Current laser power measurement, measured in 10mdBm. | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.42 |
| modSERCfgChannelRate Serial Digital Module channel data rate setting. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.420 |
| modSERCfgTTlImpedance Serial Digital Module TTL Impedance setting. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.421 |
| modSERCfgLaserDisable Serial Digital Module Laser enable/disable. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.422 |
| modPROCDescription PROC module description. | column | OctetString | .1.3.6.1.4.1.31225.1.1.4.1.1.423 |
| modTx2MonRfPower Tx2 Current RF power, measured in 10mdBm. | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.43 |
| modMaintenanceMode Module Maintenance Mode.
When in maintenance mode, a module will not produce events/traps and will not contribute to the summary alarm outputs.
Other module OIDs will be updated a… | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.430 |
| modTx2MonRfGain Tx2 Current RF gain, measured in 10mdB. | column | x 10mdB Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.44 |
| modG6CardMonSupplyVolt Card supply voltage, measured in mV. | column | mV Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.440 |
| modTx2MonFeedI Tx2 External feed current [0.1mA]. | column | 0.1mA Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.45 |
| modG6Dev1CfgBiasTSrc Set bias-t source. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.452 |
| modG6Dev1MonFeedI External feed current [0.01mA]. | column | x 0.01mA Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.454 |
| modG6Dev1MonFeedV External feed voltage [mV]. | column | mV Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.455 |
| modG6Dev1Type RF device 1 type. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.456 |
| modG6Dev1WaveLenInteger Optical Wavelength (integer part). Given in nm (truncated) | column | nm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.457 |
| modG6Dev1WaveLenDecimal Optical Wavelength (decimal part). Given in 0.01nm | column | x 0.01nm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.458 |
| modTx2MonFeedV Tx2 External feed voltage [mV]. | column | mV Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.46 |
| modG6Dev1CfgAFDThr Antenna fault detection low current threshold | column | x 0.01mA Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.464 |
| modG6Dev1CfgAFDEn Antenna fault detection enable | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.465 |
| modG6Dev1CfgAGCMode Enable automatic gain control based on received light level (RLL) | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.466 |
| modTx2MonStatus Bitmap encoding of the current configuration status of the Tx2 module.
Bit 0: Laser Status (0=Enabled, 1=Disabled)
1: FSK Tone (Digital Channel) Status (0=Enabled, 1=Disabled)
2… | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.47 |
| modG6Dev2CfgBiasTSrc Set bias-t source. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.472 |
| modG6Dev2MonFeedI External feed current [0.01mA]. | column | x 0.01mA Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.474 |
| modG6Dev2MonFeedV External feed voltage [mV]. | column | mV Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.475 |
| modG6Dev2Type RF device 2 type. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.476 |
| modG6Dev2WaveLenInteger Optical Wavelength (integer part). Given in nm (truncated) | column | nm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.477 |
| modG6Dev2WaveLenDecimal Optical Wavelength (decimal part). Given in 0.01nm | column | x 0.01nm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.478 |
| modTx2MonAlarms Bitmap encoding of the current alarm status of the Tx2 module. All bits are encoded as 0=NoAlarm 1=Alarm
Bit 0: Major Alarm
1: Minor Alarm
2: Laser Alarm
3: Automatic Gain Cont… | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.48 |
| modG6Dev2CfgAFDThr Antenna fault detection low current threshold | column | x 0.01mA Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.484 |
| modG6Dev2CfgAFDEn Antenna fault detection enable | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.485 |
| modG6Dev2CfgAGCMode Enable automatic gain control based on received light level (RLL) | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.486 |
| modTx2MonInputPower Tx2 Input power level, measured in 10mdBm | column | x 10mdB Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.49 |
| modFWVer Module firmware version and build date/time. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.31225.1.1.4.1.1.5 |
| modSN Module serial number. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.31225.1.1.4.1.1.6 |
| modTx1CfgGainSoftSet Tx1 Software Gain Control (SGC) Gain setting, measured in 10mdB | column | x 10mdB Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.60 |
| modTx1CfgAgcTarget Tx1 Automatic Gain Control target, measured in 10mdBm. | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.61 |
| modTx1CfgLaserDisable Module Tx1 Laser enable/disable. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.62 |
| modTx1CfgFskDisable Module Tx1 FSK Tone (Digital Channel) Enable/disable. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.63 |
| modTx1CfgAgc Module Tx1 Automatic Gain Control enable/disable. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.64 |
| modTx1CfgSgc Module Tx1 Software Gain Control enable/disable. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.65 |
| modTx1CfgGpsLoad Tx1 GPS dummy load enable/disable. If the module does not support GPS mode, this will have no effect. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.66 |
| modTx1CfgRFPlevelHigh Tx1 Rf Power level alarm high threshold, measured in 10mdBm. | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.67 |
| modTx1CfgRFPlevelLow Tx1 Rf Power level alarm low threshold, measured in 10mdBm. | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.68 |
| modTx1CfgLnbAlarm Tx1 LNB voltage alarm severity. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.69 |
| modOemNumber Module OEM number. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.31225.1.1.4.1.1.7 |
| modTx1CfgTECcontrol deprecated Module Tx1 TEC control enable/disable. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.70 |
| modCustomerID Module customer ID. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.31225.1.1.4.1.1.8 |
| modTx2CfgGainSoftSet Tx2 Software Gain Control (SGC) Gain setting, measured in 10mdB | column | x 10mdB Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.80 |
| modTx2CfgAgcTarget Tx2 Automatic Gain Control (AGC) target, measured in 10mdBm. | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.81 |
| modTx2CfgLaserDisable Module Tx2 Laser enable/disable. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.82 |
| modTx2CfgFskDisable Module Tx2 FSK Tone (Digital Channel) Enable/disable. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.83 |
| modTx2CfgAgc Module Tx2 Automatic Gain Control (AGC) enable/disable. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.84 |
| modTx2CfgSgc Module Tx2 Software Gain Control (SGC) enable/disable. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.85 |
| modTx2CfgGpsLoad Module Tx2 GPS dummy load enable/disable. If the module does not support GPS mode, this will have no effect. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.86 |
| modTx2CfgRFPlevelHigh Tx2 Rf Power level alarm high threshold, measured in 10mdBm. | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.87 |
| modTx2CfgRFPlevelLow Tx2 RF Power level alarm low threshold, measured in 10mdBm. | column | x 10mdBm Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.88 |
| modTx2CfgLnbAlarm Module Tx2 LNB voltage alarm severity. | column | Enumeration | .1.3.6.1.4.1.31225.1.1.4.1.1.89 |
| modMonLifeCounter Module working hours counter. Increments every 2 hours of continuous operation. | column | Integer32 | .1.3.6.1.4.1.31225.1.1.4.1.1.9 |