userSessionTimer
PERLE-IOLAN-SDS-MIB ·
.1.3.6.1.4.1.1966.12.1.4.1.1.11
Object
column
r/w
Integer32
The amount of time, in seconds, that the Session Timer will run. Use this timer to forcibly close a user's session (connection). When the Session Timer expires, the Device Server will end the connection. The default is 0 (zero), meaning that the session timer will not expire (the session is open permanently, or until the user logs out).
Context
- MIB
- PERLE-IOLAN-SDS-MIB
- OID
.1.3.6.1.4.1.1966.12.1.4.1.1.11- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- userEntry
- Table
- userTable
- Siblings
- 26
Syntax
Integer32
Values & Constraints
Object Constraints
range: 0-4294967
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| userIndex The table entry number for this user. | column | GenericTableIndex | .1.3.6.1.4.1.1966.12.1.4.1.1.1 |
| userIdleTimer The amount of time, in seconds, that the Idle Timer will run. Use
this timer to close a connection because of inactivity. When the
Idle Timer expires, because there has been no ex… | column | Integer32 | .1.3.6.1.4.1.1966.12.1.4.1.1.10 |
| userIpHost When the User Service is set to Telnet, TCP_clear or SSL_RAW, the target
host IP address. If 255.255.255.255 is specified in the configuration,
the user will be prompted for an IP… | column | Ipv4v6Address | .1.3.6.1.4.1.1966.12.1.4.1.1.12 |
| userTelnetPort The TCP port number for the Telnet session. | column | Integer32 | .1.3.6.1.4.1.1966.12.1.4.1.1.13 |
| userSSHPort The TCP port number for the SSH session. | column | Integer32 | .1.3.6.1.4.1.1966.12.1.4.1.1.14 |
| userTcpClearPort The TCP port number for the TCP-Clear or SSL-Raw session. | column | Integer32 | .1.3.6.1.4.1.1966.12.1.4.1.1.15 |
| userFramedIp Used for User Service PPP or SLIP, sets the IP address of the
remote user. Enter the address in dot decimal notation as follows:
255.255.255.254 (default)-The Device Server will u… | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.1966.12.1.4.1.1.16 |
| userSubnetBits (IPv4 only) If the remote user is on a subnet, enter the number of
bits in the subnet mask. For example, a subnet mask of 255.255.0.0
has 16 subnet/prefix bits. | column | Integer32 | .1.3.6.1.4.1.1966.12.1.4.1.1.17 |
| userIpv6InterfaceIdentifier Used for User Service PPP, sets the IP address of the remote user.
Enter the address in IPv6 format. The first 64 bits of the Interface
Identifier must be zero, therefore, ::abcd:… | column | Ipv6InterfaceId | .1.3.6.1.4.1.1966.12.1.4.1.1.18 |
| userFramedMtu Used for User Service PPP or SLIP, specifies the maximum size of
packets, in bytes, being transferred across the link. On noisy
links it might be preferable to fragment large pack… | column | Integer32 | .1.3.6.1.4.1.1966.12.1.4.1.1.19 |
| userStatus When you perform a GET on this variable, one of
the following values will be returned:
1-Indicates that the container folder is active with no changes.
2-Indicates that the contai… | column | ContainerStatus | .1.3.6.1.4.1.1966.12.1.4.1.1.2 |
| userFramedCompression Used for User Service PPP or SLIP, determines whether Van Jacobsen
Compression is used on the link. VJ compression is a means of reducing
the standard TCP/IP header from 40 octets… | column | OnOffValue | .1.3.6.1.4.1.1966.12.1.4.1.1.20 |
| userRouting Determines the routing mode used for RIP packets on the PPP and SLIP
interfaces. Values are:
None-RIP packets are neither received nor sent by the Device Server.
Send-RIP packets … | column | Enumeration | .1.3.6.1.4.1.1966.12.1.4.1.1.21 |
| userPortConnected Port user is currently connected to. -1 if user not connected | column | Integer32 | .1.3.6.1.4.1.1966.12.1.4.1.1.22 |
| userSessionTime Current User session time. | column | Integer32 | .1.3.6.1.4.1.1966.12.1.4.1.1.23 |
| userIdleTime Current Idle time | column | Integer32 | .1.3.6.1.4.1.1966.12.1.4.1.1.24 |
| userAllowAccessClusterPorts Allow/disallow the user to access to clustering ports. | column | OnOffValue | .1.3.6.1.4.1.1966.12.1.4.1.1.27 |
| userHost The name of the host. | column | OctetString | .1.3.6.1.4.1.1966.12.1.4.1.1.28 |
| userTunnel The HTTP tunnel associated with the user's host. | column | OctetString | .1.3.6.1.4.1.1966.12.1.4.1.1.29 |
| userName The user name.
To delete a user, set this field to blank.
If blank, this entry is currently unused. | column | OctetString | .1.3.6.1.4.1.1966.12.1.4.1.1.3 |
| userService The type of service that the user will use:
dsprompt, telnet, ssh, rlogin, slip, ppp, tcpclear
or sslraw. | column | Enumeration | .1.3.6.1.4.1.1966.12.1.4.1.1.4 |
| userLanguage Sets the language the user will view all Menu, CLI,
and WebManager strings. | column | Enumeration | .1.3.6.1.4.1.1966.12.1.4.1.1.5 |
| userLevel Admin-Total access to the Device Server. More than one admin user
account can exist, but we recommend that you only have one.
Normal-Limited access to the Device Server. Limited C… | column | Enumeration | .1.3.6.1.4.1.1966.12.1.4.1.1.6 |
| userHotKeyPrefix The prefix that a user types to control the current session. The
default value is hex 01, which corresponds to Ctrl-a (^a):
^a number-Switches from one session to another, press ^… | column | Hex8 | .1.3.6.1.4.1.1966.12.1.4.1.1.7 |
| userPhoneNumber The phone number the Device Server will dial to callback the user
(you must have set Callback to On). Enter the number without spaces. | column | OctetString | .1.3.6.1.4.1.1966.12.1.4.1.1.8 |
| userCallBack When On, enter a phone number for the Device Server to call the user
back (the Callback parameter is unrelated to the Line Dial parameter).
Note: the Device Server will allow call… | column | OnOffValue | .1.3.6.1.4.1.1966.12.1.4.1.1.9 |