userFramedMtu

PERLE-IOLAN-SDS-MIB · .1.3.6.1.4.1.1966.12.1.4.1.1.19

Object

column r/w Integer32

Used for User Service PPP or SLIP, specifies the maximum size of
packets, in bytes, being transferred across the link. On noisy
links it might be preferable to fragment large packets being
transferred over the link, since there will be quicker recovery
from errors. Depending on whether you have selected a User Service
of SLIP or PPP, details are as follows:
PPP-Framed MTU will be the maximum size of packets that the Device
   Server port will accept. This value is negotiated between the
   two ends of the link. The valid range is 64-1500. The default
   is 1500 bytes.
SLIP-Framed MTU will be the maximum size of packets being sent by
   the Device Server. The Device Server will send SLIP packets in
   the range 256-1006 bytes. The default value is 256 bytes.
The Framed MTU value will be used in preference to the MTU/MRU values
set for a Line.

Context

MIB: PERLE-IOLAN-SDS-MIB
OID: .1.3.6.1.4.1.1966.12.1.4.1.1.19
Type: column
Access: readwrite
Status: current
Parent: userEntry
Table: userTable
Siblings: 26

Syntax

Integer32

Values & Constraints

Object Constraints

range: 64-1500

Related Objects

Sibling Objects

Object	Type	Syntax	OID
userIndex The table entry number for this user.	column	GenericTableIndex	`.1.3.6.1.4.1.1966.12.1.4.1.1.1`
userIdleTimer The amount of time, in seconds, that the Idle Timer will run. Use this timer to close a connection because of inactivity. When the Idle Timer expires, because there has been no ex…	column	Integer32	`.1.3.6.1.4.1.1966.12.1.4.1.1.10`
userSessionTimer The amount of time, in seconds, that the Session Timer will run. Use this timer to forcibly close a user's session (connection). When the Session Timer expires, the Device Server …	column	Integer32	`.1.3.6.1.4.1.1966.12.1.4.1.1.11`
userIpHost When the User Service is set to Telnet, TCP_clear or SSL_RAW, the target host IP address. If 255.255.255.255 is specified in the configuration, the user will be prompted for an IP…	column	Ipv4v6Address	`.1.3.6.1.4.1.1966.12.1.4.1.1.12`
userTelnetPort The TCP port number for the Telnet session.	column	Integer32	`.1.3.6.1.4.1.1966.12.1.4.1.1.13`
userSSHPort The TCP port number for the SSH session.	column	Integer32	`.1.3.6.1.4.1.1966.12.1.4.1.1.14`
userTcpClearPort The TCP port number for the TCP-Clear or SSL-Raw session.	column	Integer32	`.1.3.6.1.4.1.1966.12.1.4.1.1.15`
userFramedIp Used for User Service PPP or SLIP, sets the IP address of the remote user. Enter the address in dot decimal notation as follows: 255.255.255.254 (default)-The Device Server will u…	column	SNMPv2-SMIIpAddress	`.1.3.6.1.4.1.1966.12.1.4.1.1.16`
userSubnetBits (IPv4 only) If the remote user is on a subnet, enter the number of bits in the subnet mask. For example, a subnet mask of 255.255.0.0 has 16 subnet/prefix bits.	column	Integer32	`.1.3.6.1.4.1.1966.12.1.4.1.1.17`
userIpv6InterfaceIdentifier Used for User Service PPP, sets the IP address of the remote user. Enter the address in IPv6 format. The first 64 bits of the Interface Identifier must be zero, therefore, ::abcd:…	column	Ipv6InterfaceId	`.1.3.6.1.4.1.1966.12.1.4.1.1.18`
userStatus When you perform a GET on this variable, one of the following values will be returned: 1-Indicates that the container folder is active with no changes. 2-Indicates that the contai…	column	ContainerStatus	`.1.3.6.1.4.1.1966.12.1.4.1.1.2`
userFramedCompression Used for User Service PPP or SLIP, determines whether Van Jacobsen Compression is used on the link. VJ compression is a means of reducing the standard TCP/IP header from 40 octets…	column	OnOffValue	`.1.3.6.1.4.1.1966.12.1.4.1.1.20`
userRouting Determines the routing mode used for RIP packets on the PPP and SLIP interfaces. Values are: None-RIP packets are neither received nor sent by the Device Server. Send-RIP packets …	column	Enumeration	`.1.3.6.1.4.1.1966.12.1.4.1.1.21`
userPortConnected Port user is currently connected to. -1 if user not connected	column	Integer32	`.1.3.6.1.4.1.1966.12.1.4.1.1.22`
userSessionTime Current User session time.	column	Integer32	`.1.3.6.1.4.1.1966.12.1.4.1.1.23`
userIdleTime Current Idle time	column	Integer32	`.1.3.6.1.4.1.1966.12.1.4.1.1.24`
userAllowAccessClusterPorts Allow/disallow the user to access to clustering ports.	column	OnOffValue	`.1.3.6.1.4.1.1966.12.1.4.1.1.27`
userHost The name of the host.	column	OctetString	`.1.3.6.1.4.1.1966.12.1.4.1.1.28`
userTunnel The HTTP tunnel associated with the user's host.	column	OctetString	`.1.3.6.1.4.1.1966.12.1.4.1.1.29`
userName The user name. To delete a user, set this field to blank. If blank, this entry is currently unused.	column	OctetString	`.1.3.6.1.4.1.1966.12.1.4.1.1.3`
userService The type of service that the user will use: dsprompt, telnet, ssh, rlogin, slip, ppp, tcpclear or sslraw.	column	Enumeration	`.1.3.6.1.4.1.1966.12.1.4.1.1.4`
userLanguage Sets the language the user will view all Menu, CLI, and WebManager strings.	column	Enumeration	`.1.3.6.1.4.1.1966.12.1.4.1.1.5`
userLevel Admin-Total access to the Device Server. More than one admin user account can exist, but we recommend that you only have one. Normal-Limited access to the Device Server. Limited C…	column	Enumeration	`.1.3.6.1.4.1.1966.12.1.4.1.1.6`
userHotKeyPrefix The prefix that a user types to control the current session. The default value is hex 01, which corresponds to Ctrl-a (^a): ^a number-Switches from one session to another, press ^…	column	Hex8	`.1.3.6.1.4.1.1966.12.1.4.1.1.7`
userPhoneNumber The phone number the Device Server will dial to callback the user (you must have set Callback to On). Enter the number without spaces.	column	OctetString	`.1.3.6.1.4.1.1966.12.1.4.1.1.8`
userCallBack When On, enter a phone number for the Device Server to call the user back (the Callback parameter is unrelated to the Line Dial parameter). Note: the Device Server will allow call…	column	OnOffValue	`.1.3.6.1.4.1.1966.12.1.4.1.1.9`