portPPPProtoComp
PERLE-IOLAN-SDS-MIB ·
.1.3.6.1.4.1.1966.12.1.5.5.1.14
Object
column
r/w
OnOffValue
This determines whether compression of the PPP Protocol field takes place on this link. The default is On.
Context
- MIB
- PERLE-IOLAN-SDS-MIB
- OID
.1.3.6.1.4.1.1966.12.1.5.5.1.14- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- portPPPEntry
- Table
- portPPPTable
- Siblings
- 35
Syntax
OnOffValue
- Source
- OnOffValue
- Base type
Enumeration
Values & Constraints
Type Values
1 | off |
2 | on |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| portPPPIndex portPPPIndex | column | PortNumber | .1.3.6.1.4.1.1966.12.1.5.5.1.1 |
| portPPPSecurity The type of authentication that will be done on the link: None, PAP, or CHAP.
The default is CHAP. You can use PAP or CHAP to authenticate a port or user
on the Device Server, fro… | column | Enumeration | .1.3.6.1.4.1.1966.12.1.5.5.1.10 |
| portPPPUser Complete this field only if you have specified PAP or CHAP (security
protocols) in the Security field, and you wish to dedicate this line
to a single remote user, who will be auth… | column | OctetString | .1.3.6.1.4.1.1966.12.1.5.5.1.11 |
| portPPPRemoteUser Complete this field only if you have specified PAP or CHAP (security protocols)
in the Security field, and you wish to dedicate this line to a single remote
user, who will be auth… | column | OctetString | .1.3.6.1.4.1.1966.12.1.5.5.1.12 |
| portPPPACComp This determines whether compression of the PPP Address and Control fields
take place on the link. The default is On. For most applications this should
be enabled. | column | OnOffValue | .1.3.6.1.4.1.1966.12.1.5.5.1.13 |
| portPPPVJComp This determines whether Van Jacobson Compression is used on this link.
The default is On. If your user is authenticated by the Device Server,
this VJ compression value will be ove… | column | OnOffValue | .1.3.6.1.4.1.1966.12.1.5.5.1.15 |
| portPPPMagicNegotiation Determines if a line is looping back. If enabled (On), random
numbers are sent on the link. The random numbers should be
different, unless the link loops back. The default is Off. | column | OnOffValue | .1.3.6.1.4.1.1966.12.1.5.5.1.16 |
| portPPPIPAddrNegotiation Specifies whether or not IP address negotiation will take place.
IP address negotiation is where the Device Server allows the
remote end to specify its IP address. The default val… | column | OnOffValue | .1.3.6.1.4.1.1966.12.1.5.5.1.17 |
| portPPPCRTimeout The maximum time, in seconds, that LCP (Link Control Protocol)
will wait before it considers a configure request packet to have
been lost. | column | Integer32 | .1.3.6.1.4.1.1966.12.1.5.5.1.18 |
| portPPPTRTimeout The maximum time, in seconds, that LCP (Link Control Protocol)
will wait before it considers a terminate request packet to have
been lost. | column | Integer32 | .1.3.6.1.4.1.1966.12.1.5.5.1.19 |
| portPPPStatus When you perform a GET on this variable, one of
the following values will be returned:
1-Indicates that the container folder is active with no changes.
2-Indicates that the contai… | column | ContainerStatus | .1.3.6.1.4.1.1966.12.1.5.5.1.2 |
| portPPPCRRetry The maximum number of times a configure request packet will
be sent before the link is terminated. | column | Integer32 | .1.3.6.1.4.1.1966.12.1.5.5.1.20 |
| portPPPTRRetry The maximum number of times a terminate request packet will
be sent before the link is terminated. | column | Integer32 | .1.3.6.1.4.1.1966.12.1.5.5.1.21 |
| portPPPNakRetry The maximum number of times a configure NAK packet will
be sent before the link is terminated. | column | Integer32 | .1.3.6.1.4.1.1966.12.1.5.5.1.22 |
| portPPPAuthTimeout The timeout, in seconds, during which successful PAP or
CHAP authentication must take place (when PAP or CHAP is
turned On). If the timer expires before the remote end has
been au… | column | Integer32 | .1.3.6.1.4.1.1966.12.1.5.5.1.23 |
| portPPPRoamingCallback A user can enter a telephone number that the Device Server
will use to callback him/her. This feature is particularly
useful for a mobile user. Roaming callback can only work when… | column | OnOffValue | .1.3.6.1.4.1.1966.12.1.5.5.1.24 |
| portPPPChallengInterval The interval, in seconds, for which the Device Server will
issue a CHAP re-challenge to the remote end. During CHAP
authentication, an initial CHAP challenge takes place, and
is u… | column | Integer32 | .1.3.6.1.4.1.1966.12.1.5.5.1.25 |
| portPPPRouting Determines the routing mode (RIP, Routing Information Protocol)
used on the PPP interface as one of the following options:
None-Disables RIP over the PPP/SLIP interface.
Send-Send… | column | Enumeration | .1.3.6.1.4.1.1966.12.1.5.5.1.26 |
| portPPPDynamicDNSEnabled Enable/disable dynamic DNS. | column | OnOffValue | .1.3.6.1.4.1.1966.12.1.5.5.1.27 |
| portPPPDynamicDNSHostname Host name. | column | OctetString | .1.3.6.1.4.1.1966.12.1.5.5.1.28 |
| portPPPDynamicDNSUserName user name. | column | OctetString | .1.3.6.1.4.1.1966.12.1.5.5.1.29 |
| portPPPLocalIpAddr The IPv4 IP address of the Device Server end of the PPP
link. For routing to work, you must enter a local IP
address. Choose an address that is part of the same network
or subnetw… | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.1966.12.1.5.5.1.3 |
| portPPPDynamicDNSPassword Password. | column | OctetString | .1.3.6.1.4.1.1966.12.1.5.5.1.30 |
| portPPPDynamicDNSStatusString Dynamic DNS Status | column | OctetString | .1.3.6.1.4.1.1966.12.1.5.5.1.31 |
| portPPPMSDirectConnection Set for Microsoft PPP connection working mode | column | Enumeration | .1.3.6.1.4.1.1966.12.1.5.5.1.32 |
| portPPPIPv6Prefix You can optionally specify an IPv6 global network prefix
that the Device Server will advertise to the device at the
other end of the PPP link. Default: 0:0:0:0 | column | Ipv4v6Address | .1.3.6.1.4.1.1966.12.1.5.5.1.33 |
| portPPPIPv6PrefixBits Specify the prefix bits for the IPv6 global network prefix.
Default is 64. | column | Integer32 | .1.3.6.1.4.1.1966.12.1.5.5.1.34 |
| portPPPEchoTimeout The timeout, in seconds, to wait for an Echo reply. | column | Integer32 | .1.3.6.1.4.1.1966.12.1.5.5.1.35 |
| portPPPEchoRetry The maximum number of Echo reply timeouts before
the link is terminated. | column | Integer32 | .1.3.6.1.4.1.1966.12.1.5.5.1.36 |
| portPPPRemoteIpAddr The IPv4 IP address of the remote end of the PPP link. Choose an
address that is part of the same network or subnetwork as the
Device Server. If you set the PPP parameter IP Addre… | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.1966.12.1.5.5.1.4 |
| portPPPSubnetBits The number of bits in the subnet mask. For example, a subnet mask
of 255.255.0.0 has 16 subnet/prefix bits. If your user is
authenticated by RADIUS and the RADIUS parameter Framed… | column | Integer32 | .1.3.6.1.4.1.1966.12.1.5.5.1.5 |
| portPPPIpV6LocalIpAddr The local IPv6 interface identifier of the Device Server end of the
PPP link. For routing to work, you must enter a local IP address.
Choose an address that is part of the same ne… | column | Ipv6InterfaceId | .1.3.6.1.4.1.1966.12.1.5.5.1.6 |
| portPPPIpV6RemoteIpAddr The remote IPv6 interface identifier of the remote end of the PPP link.
Choose an address that is part of the same network or subnetwork as the
Device Server. If you set the PPP p… | column | Ipv6InterfaceId | .1.3.6.1.4.1.1966.12.1.5.5.1.7 |
| portPPPAccm Specifies the ACCM (Asynchronous Control Character Map) characters that
should be escaped from the data stream. This is entered as a 32-bit
hexadecimal number with each bit specif… | column | Hex32 | .1.3.6.1.4.1.1966.12.1.5.5.1.8 |
| portPPPMru The Maximum Receive Unit (MRU) parameter specifies the maximum size of PPP
packets that the Device Server's port will accept. Enter a value between
64 and 1500 bytes; for example,… | column | Integer32 | .1.3.6.1.4.1.1966.12.1.5.5.1.9 |