portPPPAccm

PERLE-IOLAN-SDS-MIB · .1.3.6.1.4.1.1966.12.1.5.5.1.8
MIB view Table view

Object

column r/w Hex32 
Specifies the ACCM (Asynchronous Control Character Map) characters that
should be escaped from the data stream. This is entered as a 32-bit
hexadecimal number with each bit specifying whether or not the corresponding
character should be escaped. The bits are specified as the most significant
bit first and are numbered 31-0. Thus if bit 17 is set, the 17th character
should be escaped, that is, 0x11 (XON). So entering the value 000a0000 will
cause the control characters 0x11 (XON) and 0x13 (XOFF) to be escaped on the
link, thus allowing the use of XON/XOFF (software) flow control. If you have
selected Soft Flow Control on the Line, you must enter a value of 000a0000
for the ACCM. The default value is 00000000, which means no characters will
be escaped.

Context

MIB
PERLE-IOLAN-SDS-MIB
OID
.1.3.6.1.4.1.1966.12.1.5.5.1.8
Type
column
Access
readwrite
Status
current
Parent
portPPPEntry
Table
portPPPTable
Siblings
35

Syntax

Hex32
Source
Hex32
Base type
OctetString

Values & Constraints

Type Constraints
range: 4

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
portPPPIndex
portPPPIndex
columnPortNumber.1.3.6.1.4.1.1966.12.1.5.5.1.1
portPPPSecurity
The type of authentication that will be done on the link: None, PAP, or CHAP. The default is CHAP. You can use PAP or CHAP to authenticate a port or user on the Device Server, fro…
columnEnumeration.1.3.6.1.4.1.1966.12.1.5.5.1.10
portPPPUser
Complete this field only if you have specified PAP or CHAP (security protocols) in the Security field, and you wish to dedicate this line to a single remote user, who will be auth…
columnOctetString.1.3.6.1.4.1.1966.12.1.5.5.1.11
portPPPRemoteUser
Complete this field only if you have specified PAP or CHAP (security protocols) in the Security field, and you wish to dedicate this line to a single remote user, who will be auth…
columnOctetString.1.3.6.1.4.1.1966.12.1.5.5.1.12
portPPPACComp
This determines whether compression of the PPP Address and Control fields take place on the link. The default is On. For most applications this should be enabled.
columnOnOffValue.1.3.6.1.4.1.1966.12.1.5.5.1.13
portPPPProtoComp
This determines whether compression of the PPP Protocol field takes place on this link. The default is On.
columnOnOffValue.1.3.6.1.4.1.1966.12.1.5.5.1.14
portPPPVJComp
This determines whether Van Jacobson Compression is used on this link. The default is On. If your user is authenticated by the Device Server, this VJ compression value will be ove…
columnOnOffValue.1.3.6.1.4.1.1966.12.1.5.5.1.15
portPPPMagicNegotiation
Determines if a line is looping back. If enabled (On), random numbers are sent on the link. The random numbers should be different, unless the link loops back. The default is Off.
columnOnOffValue.1.3.6.1.4.1.1966.12.1.5.5.1.16
portPPPIPAddrNegotiation
Specifies whether or not IP address negotiation will take place. IP address negotiation is where the Device Server allows the remote end to specify its IP address. The default val…
columnOnOffValue.1.3.6.1.4.1.1966.12.1.5.5.1.17
portPPPCRTimeout
The maximum time, in seconds, that LCP (Link Control Protocol) will wait before it considers a configure request packet to have been lost.
columnInteger32.1.3.6.1.4.1.1966.12.1.5.5.1.18
portPPPTRTimeout
The maximum time, in seconds, that LCP (Link Control Protocol) will wait before it considers a terminate request packet to have been lost.
columnInteger32.1.3.6.1.4.1.1966.12.1.5.5.1.19
portPPPStatus
When you perform a GET on this variable, one of the following values will be returned: 1-Indicates that the container folder is active with no changes. 2-Indicates that the contai…
columnContainerStatus.1.3.6.1.4.1.1966.12.1.5.5.1.2
portPPPCRRetry
The maximum number of times a configure request packet will be sent before the link is terminated.
columnInteger32.1.3.6.1.4.1.1966.12.1.5.5.1.20
portPPPTRRetry
The maximum number of times a terminate request packet will be sent before the link is terminated.
columnInteger32.1.3.6.1.4.1.1966.12.1.5.5.1.21
portPPPNakRetry
The maximum number of times a configure NAK packet will be sent before the link is terminated.
columnInteger32.1.3.6.1.4.1.1966.12.1.5.5.1.22
portPPPAuthTimeout
The timeout, in seconds, during which successful PAP or CHAP authentication must take place (when PAP or CHAP is turned On). If the timer expires before the remote end has been au…
columnInteger32.1.3.6.1.4.1.1966.12.1.5.5.1.23
portPPPRoamingCallback
A user can enter a telephone number that the Device Server will use to callback him/her. This feature is particularly useful for a mobile user. Roaming callback can only work when…
columnOnOffValue.1.3.6.1.4.1.1966.12.1.5.5.1.24
portPPPChallengInterval
The interval, in seconds, for which the Device Server will issue a CHAP re-challenge to the remote end. During CHAP authentication, an initial CHAP challenge takes place, and is u…
columnInteger32.1.3.6.1.4.1.1966.12.1.5.5.1.25
portPPPRouting
Determines the routing mode (RIP, Routing Information Protocol) used on the PPP interface as one of the following options: None-Disables RIP over the PPP/SLIP interface. Send-Send…
columnEnumeration.1.3.6.1.4.1.1966.12.1.5.5.1.26
portPPPDynamicDNSEnabled
Enable/disable dynamic DNS.
columnOnOffValue.1.3.6.1.4.1.1966.12.1.5.5.1.27
portPPPDynamicDNSHostname
Host name.
columnOctetString.1.3.6.1.4.1.1966.12.1.5.5.1.28
portPPPDynamicDNSUserName
user name.
columnOctetString.1.3.6.1.4.1.1966.12.1.5.5.1.29
portPPPLocalIpAddr
The IPv4 IP address of the Device Server end of the PPP link. For routing to work, you must enter a local IP address. Choose an address that is part of the same network or subnetw…
columnSNMPv2-SMIIpAddress.1.3.6.1.4.1.1966.12.1.5.5.1.3
portPPPDynamicDNSPassword
Password.
columnOctetString.1.3.6.1.4.1.1966.12.1.5.5.1.30
portPPPDynamicDNSStatusString
Dynamic DNS Status
columnOctetString.1.3.6.1.4.1.1966.12.1.5.5.1.31
portPPPMSDirectConnection
Set for Microsoft PPP connection working mode
columnEnumeration.1.3.6.1.4.1.1966.12.1.5.5.1.32
portPPPIPv6Prefix
You can optionally specify an IPv6 global network prefix that the Device Server will advertise to the device at the other end of the PPP link. Default: 0:0:0:0
columnIpv4v6Address.1.3.6.1.4.1.1966.12.1.5.5.1.33
portPPPIPv6PrefixBits
Specify the prefix bits for the IPv6 global network prefix. Default is 64.
columnInteger32.1.3.6.1.4.1.1966.12.1.5.5.1.34
portPPPEchoTimeout
The timeout, in seconds, to wait for an Echo reply.
columnInteger32.1.3.6.1.4.1.1966.12.1.5.5.1.35
portPPPEchoRetry
The maximum number of Echo reply timeouts before the link is terminated.
columnInteger32.1.3.6.1.4.1.1966.12.1.5.5.1.36
portPPPRemoteIpAddr
The IPv4 IP address of the remote end of the PPP link. Choose an address that is part of the same network or subnetwork as the Device Server. If you set the PPP parameter IP Addre…
columnSNMPv2-SMIIpAddress.1.3.6.1.4.1.1966.12.1.5.5.1.4
portPPPSubnetBits
The number of bits in the subnet mask. For example, a subnet mask of 255.255.0.0 has 16 subnet/prefix bits. If your user is authenticated by RADIUS and the RADIUS parameter Framed…
columnInteger32.1.3.6.1.4.1.1966.12.1.5.5.1.5
portPPPIpV6LocalIpAddr
The local IPv6 interface identifier of the Device Server end of the PPP link. For routing to work, you must enter a local IP address. Choose an address that is part of the same ne…
columnIpv6InterfaceId.1.3.6.1.4.1.1966.12.1.5.5.1.6
portPPPIpV6RemoteIpAddr
The remote IPv6 interface identifier of the remote end of the PPP link. Choose an address that is part of the same network or subnetwork as the Device Server. If you set the PPP p…
columnIpv6InterfaceId.1.3.6.1.4.1.1966.12.1.5.5.1.7
portPPPMru
The Maximum Receive Unit (MRU) parameter specifies the maximum size of PPP packets that the Device Server's port will accept. Enter a value between 64 and 1500 bytes; for example,…
columnInteger32.1.3.6.1.4.1.1966.12.1.5.5.1.9