inletLinePairSensorUnits
PDU2-MIB ·
.1.3.6.1.4.1.13742.6.3.3.8.1.6
Object
column
SensorUnitsEnumeration
The unit in which the sensor reading is reported. This parameter does not apply to sensors without numerical reading.
Context
- MIB
- PDU2-MIB
- OID
.1.3.6.1.4.1.13742.6.3.3.8.1.6- Type
- column
- Access
- readonly
- Status
- current
- Parent
- inletLinePairSensorConfigurationEntry
- Table
- inletLinePairSensorConfigurationTable
- Siblings
- 18
Syntax
SensorUnitsEnumeration
- Source
- SensorUnitsEnumeration
- Base type
Enumeration
Values & Constraints
Type Values
-1 | none |
0 | other |
1 | volt |
2 | amp |
3 | watt |
4 | voltamp |
5 | wattHour |
6 | voltampHour |
7 | degreeC |
8 | hertz |
9 | percent |
10 | meterpersec |
11 | pascal |
12 | psi |
13 | g |
14 | degreeF |
15 | feet |
16 | inches |
17 | cm |
18 | meters |
19 | rpm |
20 | degrees |
21 | lux |
22 | grampercubicmeter |
23 | var |
24 | feetpersec |
25 | lbspercubicfoot |
26 | microgrampercubicmeter |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| inletLinePairSensorMaximum The largest possible reading as an unsigned integer.
The value of this OID variable should be scaled by
inletLinePairSensorDecimalDigits. For example, if the value is 1 and
inletL… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.13742.6.3.3.8.1.11 |
| inletLinePairSensorMinimum The smallest possible reading as an unsigned integer.
The value of this OID variable should be scaled by
inletLinePairSensorDecimalDigits. For example, if the value is 1 and
inlet… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.13742.6.3.3.8.1.12 |
| inletLinePairSensorHysteresis The hysteresis used when crossing a threshold towards the normal state.
The value of this OID variable should be scaled by
inletLinePairSensorDecimalDigits. For example, if the va… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.13742.6.3.3.8.1.13 |
| inletLinePairSensorStateChangeDelay The delay measured in samples before a state is asserted.
If the value is zero, then the state is asserted as soon as
it is detected; if it is non-zero, say n, then the assertion
… | column | Unsigned32 | .1.3.6.1.4.1.13742.6.3.3.8.1.14 |
| inletLinePairSensorLowerCriticalThreshold The lower critical threshold as an unsigned integer.
The value of this OID variable should be scaled by
inletLinePairSensorDecimalDigits. For example, if the value is 1 and
inletL… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.13742.6.3.3.8.1.21 |
| inletLinePairSensorLowerWarningThreshold The lower warning threshold as an unsigned integer.
The value of this OID variable should be scaled by
inletLinePairSensorDecimalDigits. For example, if the value is 1 and
inletLi… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.13742.6.3.3.8.1.22 |
| inletLinePairSensorUpperCriticalThreshold The upper critical threshold as an unsigned integer.
The value of this OID variable should be scaled by
inletLinePairSensorDecimalDigits. For example, if the value is 1 and
inletL… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.13742.6.3.3.8.1.23 |
| inletLinePairSensorUpperWarningThreshold The upper warning threshold as an unsigned integer.
The value of this OID variable should be scaled by
inletLinePairSensorDecimalDigits. For example, if the value is 1 and
inletLi… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.13742.6.3.3.8.1.24 |
| inletLinePairSensorEnabledThresholds A bit string indicating which thresholds are enabled.
This parameter does not apply to sensors without numerical reading. | column | Bits | .1.3.6.1.4.1.13742.6.3.3.8.1.25 |
| inletLinePairSensorSignedMaximum The largest possible reading as a signed integer.
The value of this OID variable should be scaled by
inletLinePairSensorDecimalDigits. For example, if the value is 1 and
inletLine… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.13742.6.3.3.8.1.26 |
| inletLinePairSensorSignedMinimum The smallest possible reading as a signed integer.
The value of this OID variable should be scaled by
inletLinePairSensorDecimalDigits. For example, if the value is 1 and
inletLin… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.13742.6.3.3.8.1.27 |
| inletLinePairSensorSignedLowerCriticalThreshold The lower critical threshold as a signed integer.
The value of this OID variable should be scaled by
inletLinePairSensorDecimalDigits. For example, if the value is 1 and
inletLine… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.13742.6.3.3.8.1.28 |
| inletLinePairSensorSignedLowerWarningThreshold The lower warning threshold as a signed integer.
The value of this OID variable should be scaled by
inletLinePairSensorDecimalDigits. For example, if the value is 1 and
inletLineP… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.13742.6.3.3.8.1.29 |
| inletLinePairSensorSignedUpperCriticalThreshold The upper critical threshold as a signed integer.
The value of this OID variable should be scaled by
inletLinePairSensorDecimalDigits. For example, if the value is 1 and
inletLine… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.13742.6.3.3.8.1.30 |
| inletLinePairSensorSignedUpperWarningThreshold The upper warning threshold as a signed integer.
The value of this OID variable should be scaled by
inletLinePairSensorDecimalDigits. For example, if the value is 1 and
inletLineP… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.13742.6.3.3.8.1.31 |
| inletLinePairSensorLogAvailable Is data logging enabled for this sensor? | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.13742.6.3.3.8.1.4 |
| inletLinePairSensorDecimalDigits The number of digits displayed to the right of the decimal point.
This parameter does not apply to sensors without numerical reading. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.13742.6.3.3.8.1.7 |
| inletLinePairSensorResolution The resolution: the minimum difference between any two measured values
The value of this OID variable should be scaled by
inletLinePairSensorDecimalDigits. For example, if the val… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.13742.6.3.3.8.1.9 |