pdug5InputPhaseCurrentThResetThld
PANDUIT-MIB ·
.1.3.6.1.4.1.19536.10.1.2.2.1.28
Object
The Reset threshold is the number of amps the reading needs to fall below the threshold setting for the condition to be cleared. Units are 0.01 amps.
Context
- MIB
- PANDUIT-MIB
- OID
.1.3.6.1.4.1.19536.10.1.2.2.1.28- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- pdug5InputPhaseEntry
- Table
- pdug5InputPhaseTable
- Siblings
- 42
Syntax
SNMPv2-SMIInteger32
- Source
- SNMPv2-SMIInteger32
- Base type
Integer32
Values & Constraints
Type Constraints
range: -2147483648..2147483647
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| pdug5InputPhaseIndex Index for the pdug5InputEntry table. | column | Integer32 | .1.3.6.1.4.1.19536.10.1.2.2.1.1 |
| pdug5InputPhaseCurrentRating Rated current capacity of the input. A negative value indicates that
the hardware current capacity is unknown. Units are 0.01 amps. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.19536.10.1.2.2.1.10 |
| pdug5InputPhaseCurrent An input current measurement value. Units are 0.01 amps. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.19536.10.1.2.2.1.11 |
| pdug5InputPhaseCurrentThStatus Status of the measured input current relative to the configured thresholds. | column | Enumeration | .1.3.6.1.4.1.19536.10.1.2.2.1.12 |
| pdug5InputPhaseCurrentThLowerWarning Lower warning threshold. Units are 0.01 amps. A negative value indicates
that this object is not available. | column | Integer32 | .1.3.6.1.4.1.19536.10.1.2.2.1.13 |
| pdug5InputPhaseCurrentThLowerCritical Lower critical threshold. Units are 0.01 amps. A negative value indicates
that this object is not available. | column | Integer32 | .1.3.6.1.4.1.19536.10.1.2.2.1.14 |
| pdug5InputPhaseCurrentThUpperWarning Upper warning threshold. Units are 0.01 amps. A negative value indicates
that this object is not available. | column | Integer32 | .1.3.6.1.4.1.19536.10.1.2.2.1.15 |
| pdug5InputPhaseCurrentThUpperCritical Upper critical threshold. Units are 0.01 amps. A negative value indicates
that this object is not available. | column | Integer32 | .1.3.6.1.4.1.19536.10.1.2.2.1.16 |
| pdug5InputPhaseCurrentPercentLoad Current percent load, based on the rated current capacity. Units are
percentage, for example 80% will be returned as 80. A negative
value indicates that this object is not avail… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.19536.10.1.2.2.1.17 |
| pdug5InputPhasePowerMeasType Which input wire is being measured in this table row - single phase, neutral, phase 1,
phase 2, or phase 3. | column | Enumeration | .1.3.6.1.4.1.19536.10.1.2.2.1.18 |
| pdug5InputPhasePowerVA An input VA value. Units are VA. A negative value indicates
that this object is not available. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.19536.10.1.2.2.1.19 |
| pdug5InputPhaseVoltageMeasType Value indicates what input voltage is being measured in this table row - single phase
voltage, phase 1 to neutral, phase 2 to neutral, phase 3 to neutral, phase 1 to phase 2,
phas… | column | Enumeration | .1.3.6.1.4.1.19536.10.1.2.2.1.2 |
| pdug5InputPhasePowerWatts An input Watts value. Units are Watts. A negative value indicates
that this object is not available. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.19536.10.1.2.2.1.20 |
| pdug5InputPhasePowerWattHour A Watt-Hour value for each Input phase. Units are WH. This value can be reset to 0
using GUI. In that case, the pdug5InputPhasePowerWattHourTimer will be reset as well
A negative… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.19536.10.1.2.2.1.21 |
| pdug5InputPhasePowerWattHourTimer Timestamp of when input Watt-hours (inputWh) was last reset. | column | OctetString | .1.3.6.1.4.1.19536.10.1.2.2.1.22 |
| pdug5InputPhasePowerFactor An input PF value. Units are in hundredths, for example a power factor
of 0.95 would be returned as 95, and 0.92 would be returned
as 92. A negative value indicates that this ob… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.19536.10.1.2.2.1.23 |
| pdug5InputPhasePowerVAR An input VAR value. Units are VAR. A negative value indicates
that this object is not available. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.19536.10.1.2.2.1.24 |
| pdug5InputPhaseVoltageThResetThld The Reset threshold is the number of volts the reading needs to fall below
the threshold setting for the condition to be cleared. Units are 0.1 volts. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.19536.10.1.2.2.1.25 |
| pdug5InputPhaseVoltageThChangeDelay The number of consecutive sample that the condition is present before
an alarm is raised. | column | Integer32 | .1.3.6.1.4.1.19536.10.1.2.2.1.26 |
| pdug5InputPhaseVoltageThCtrl Input phase voltage alarm threshold control:
bit 0: up critical alarm control bit, 0 - enable, 1 - disable
bit 1: up warning alarm control bit, 0 - enable, 1 - disable
b… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.19536.10.1.2.2.1.27 |
| pdug5InputPhaseCurrentThChangeDelay The number of consecutive sample that the condition is present before
an alarm is raised. | column | Integer32 | .1.3.6.1.4.1.19536.10.1.2.2.1.29 |
| pdug5InputPhaseVoltage An input voltage measurement value. Values is in 0.1 V. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.19536.10.1.2.2.1.3 |
| pdug5InputPhaseCurrentThCtrl Input phase current alarm threshold control:
bit 0: up critical alarm control bit, 0 - enable, 1 - disable
bit 1: up warning alarm control bit, 0 - enable, 1 - disable
b… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.19536.10.1.2.2.1.30 |
| pdug5InputPowerThresholdThLowerWarning Lower warning Power threshold. Units are in Watts. A negative value indicates
that this object is not available. | column | Integer32 | .1.3.6.1.4.1.19536.10.1.2.2.1.31 |
| pdug5InputPowerThresholdThLowerCritical Lower critical Power threshold. Units are in Watts. A negative value indicates
that this object is not available. | column | Integer32 | .1.3.6.1.4.1.19536.10.1.2.2.1.32 |
| pdug5InputPowerThresholdThUpperWarning Upper warning Power threshold. Units are in Watts. A negative value indicates
that this object is not available. | column | Integer32 | .1.3.6.1.4.1.19536.10.1.2.2.1.33 |
| pdug5InputPowerThresholdThUpperCritical Upper critical Power threshold. Units are in Watts. A negative value indicates
that this object is not available. | column | Integer32 | .1.3.6.1.4.1.19536.10.1.2.2.1.34 |
| pdug5InputPowerThresholdThResetThld The Reset threshold is the number of watts the reading needs to fall below
the threshold setting for the condition to be cleared. Units are watts. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.19536.10.1.2.2.1.35 |
| pdug5InputPowerThresholdThChangeDelay The number of consecutive sample that the condition is present before
an alarm is raised. | column | Integer32 | .1.3.6.1.4.1.19536.10.1.2.2.1.36 |
| pdug5InputPowerThresholdThCtrl Power alarm threshold control:
bit 0: up critical alarm control bit, 0 - enable, 1 - disable
bit 1: up warning alarm control bit, 0 - enable, 1 - disable
bit 2: low war… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.19536.10.1.2.2.1.37 |
| pdug5InputEnergyThresholdThUpperWarning Upper warning Energy threshold. Units are in Watts. A negative value indicates
that this object is not available. | column | Integer32 | .1.3.6.1.4.1.19536.10.1.2.2.1.38 |
| pdug5InputEnergyThresholdThUpperCritical Upper critical Energy threshold. Units are in Watts. A negative value indicates
that this object is not available. | column | Integer32 | .1.3.6.1.4.1.19536.10.1.2.2.1.39 |
| pdug5InputPhaseVoltageThStatus Status of the measured input voltage relative to the configured thresholds. | column | Enumeration | .1.3.6.1.4.1.19536.10.1.2.2.1.4 |
| pdug5InputEnergyThresholdThResetThld The Reset threshold is the number of watts the reading needs to fall below
the threshold setting for the condition to be cleared. Units are watts. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.19536.10.1.2.2.1.40 |
| pdug5InputEnergyThresholdThChangeDelay The number of consecutive sample that the condition is present before
an alarm is raised. | column | Integer32 | .1.3.6.1.4.1.19536.10.1.2.2.1.41 |
| pdug5InputEnergyThresholdThCtrl Energy alarm threshold control:
bit 0: up critical alarm control bit, 0 - enable, 1 - disable
bit 1: up warning alarm control bit, 0 - enable, 1 - disable
bit 2: low wa… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.19536.10.1.2.2.1.42 |
| pdug5InputPhasePowerThStatus Status of the measured input current relative to the configured thresholds. | column | Enumeration | .1.3.6.1.4.1.19536.10.1.2.2.1.43 |
| pdug5InputPhaseVoltageThLowerWarning Lower warning threshold. Units are 0.1 volts. A negative value indicates
that this object is not available. | column | Integer32 | .1.3.6.1.4.1.19536.10.1.2.2.1.5 |
| pdug5InputPhaseVoltageThLowerCritical Lower critical threshold. Units are 0.1 volts. A negative value indicates
that this object is not available. | column | Integer32 | .1.3.6.1.4.1.19536.10.1.2.2.1.6 |
| pdug5InputPhaseVoltageThUpperWarning Upper warning threshold. Units are 0.1 volts. A negative value indicates
that this object is not available. | column | Integer32 | .1.3.6.1.4.1.19536.10.1.2.2.1.7 |
| pdug5InputPhaseVoltageThUpperCritical Upper critical threshold. Units are 0.1 volts. A negative value indicates
that this object is not available. | column | Integer32 | .1.3.6.1.4.1.19536.10.1.2.2.1.8 |
| pdug5InputPhaseCurrentMeasType Which input wire is being measured in this table row - single phase, neutral, phase 1,
phase 2, or phase 3. | column | Enumeration | .1.3.6.1.4.1.19536.10.1.2.2.1.9 |