ntnQosConfigDefaultBufferingCaps
NTN-QOS-POLICY-EVOL-PIB ·
.1.3.6.1.4.1.45.4.7.1.11.7
Object
scalar
r/w
Enumeration
The value of this attribute determines the method
through which buffering resources are allocated to
ports sharing a pool of buffers.
The buffering resources associated with a series
of ports are finite. This buffer pool may be
statistically allocated to the individual ports
sharing the pool or they may be allocated such that
the traffic pattern dictates which ports temporarily
consume the majority of the buffers.
The value of this attribute determines the level
of buffer sharing or over-allocation that can take
place among ports sharing a buffer pool. Higher
levels of over-allocation increase the likelyhood
(under heavy load) of a relatively few number of
ports consuming all the buffers in a pool, causing
packets to be dropped on other ports due to buffer
starvation.
A value of 'minimumOverAllocation(1)' indicates
that only a small amount of resource sharing is
allowed. Greater resource sharing is allowed if the
value of this attribute is 'mediumOverAllocation(2)'
and the chance of over-allocation occurring is
maximized by the specifying that 'maximumOverAllocation(3)'
is desired.
In lossless mode, the buffer allocation and thresholds
are such that pause frames are generated to the endstations
prior to frames being discarded due to lack of available
buffers, allowing the end stattions to back off. This
mode allows for lossless behavior at the expense of throughput.
Lossless PFC mode operates in a similar fashion to
lossless but provides the service on a per-priority
(802.1p) basis.
'spb-scaled(6)' is a mode similar to 'mediumOverAllocation(2)',
but optimized for scaled SPB setups.
The value of this attribute is consulted when
the system is initialized. Changing the value of
this attribute will therefore not take effect
until after the system is restarted.
Context
- MIB
- NTN-QOS-POLICY-EVOL-PIB
- OID
.1.3.6.1.4.1.45.4.7.1.11.7- Type
- scalar
- Access
- readwrite
- Status
- current
- Parent
- ntnQosPolicyAgtClasses
- Siblings
- 22
Syntax
Enumeration
Values & Constraints
No enumerated values or constraints recorded.
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| ntnQosPrcSupportTable Each instance of this class specifies a PRC that the device
supports and a bit string to indicate the attributes of the
class that are supported. | table | - | .1.3.6.1.4.1.45.4.7.1.11.1 |
| ntnQosConfigDappEnable Dictates whether the DoS Attack Prevention Package
(DAPP) is enabled on all applicable ports and, when
enabled, if resources will be allocated to track and
report on DoS attack d… | scalar | Enumeration | .1.3.6.1.4.1.45.4.7.1.11.10 |
| ntnQosConfigDappMinTcpHdrSize DAPP minimum TCP header length allowed. Used when
performing TCP fragment validation. IPv4 TCP first
fragment packets will be dropped if the TCP header
(IP payload) is less than t… | scalar | Integer32 | .1.3.6.1.4.1.45.4.7.1.11.11 |
| ntnQosConfigDappIpv4IcmpMaxLength DAPP maximum IPv4 ICMP length. Used when performing
ICMP validation. IPv4 ICMP packets will be dropped
if the length (IP payload) exceeds this value. | scalar | Integer32 | .1.3.6.1.4.1.45.4.7.1.11.12 |
| ntnQosConfigDappIpv6IcmpMaxLength DAPP maximum IPv6 ICMP length. Used when performing
ICMP validation. IPv6 ICMP packets will be dropped
if the length exceeds this value. | scalar | Integer32 | .1.3.6.1.4.1.45.4.7.1.11.13 |
| ntnQosConfigNtApplicationMode Controls NT Application Mode processing. When enabled,
identified NT application traffic will be given preferential
treatment over non-NT application traffic. 'Mixed' mode
process… | scalar | Enumeration | .1.3.6.1.4.1.45.4.7.1.11.14 |
| ntnQosConfigQosOperMode Controls overall QoS processing for the system. When
enabled, all QoS functionality can be exercised by the
user. When disabled, installed QoS components are
temporarily removed … | scalar | Enumeration | .1.3.6.1.4.1.45.4.7.1.11.15 |
| ntnQosConfigTrustedProcessingMode Controls filter usage related to Trusted interface
class processing on platforms using filters to support
treating traffic as trusted. A mode of 'partialDscpMapping(1)'
causes fil… | scalar | Enumeration | .1.3.6.1.4.1.45.4.7.1.11.16 |
| ntnQosConfigResetToPartialDefaults Most installed QoS policy state information can
be deleted and reset to the device's default state
by setting the value of this object to 'true(1)'.
QoS data that requires a sy… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.45.4.7.1.11.17 |
| ntnQosConfigClearStats All counters that are associated with QoS policies
are reset to zero by setting the value of this object
to 'true(1)'. The value 'false(2)' will always be
returned when queryin… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.45.4.7.1.11.18 |
| ntnQosConfigFcoeRedirOperMode Controls the FCoE redirection service for the system.
Enabling the service will initiate validation and
possible reservation of the resources that are required
for service activat… | scalar | Enumeration | .1.3.6.1.4.1.45.4.7.1.11.19 |
| ntnQosPolicyDeviceIdentTable This class contains a single policy rule instance that
contains device-specific information. | table | - | .1.3.6.1.4.1.45.4.7.1.11.2 |
| ntnQosConfigFcoeControllerMacAddr The 802 MAC address of the FCoE Network Controller
(FNC) that is used in conjunction with the FCoE
redirection service. Must be defined prior to
enabling the FCoE redirection serv… | scalar | SNMPv2-TCMacAddress | .1.3.6.1.4.1.45.4.7.1.11.20 |
| ntnQosConfigFcoeRedirAvail Controls access to the FCoE Redirect functionality.
A value of 'accessible(1)' indicates that the FCoE
support can be accessed by an external FCoE Network
Controller (FNC). A valu… | scalar | Enumeration | .1.3.6.1.4.1.45.4.7.1.11.21 |
| ntnQosConfigFcoeControllerIfIndex The interface index of the FCoE Network Controller
(FNC) that is used in conjunction with the FCoE
redirection service. Must be defined prior to
enabling the FCoE redirection serv… | scalar | IF-MIBInterfaceIndexOrZero | .1.3.6.1.4.1.45.4.7.1.11.22 |
| ntnQosConfigFcoeControllerVlan The VLAN associated with the FCoE Network Controller
(FNC) that is used in conjunction with the FCoE
redirection service. Must be defined prior to
enabling the FCoE redirection se… | scalar | Integer32 | .1.3.6.1.4.1.45.4.7.1.11.23 |
| ntnQosConfigResetToDefaults All installed QoS policy state information can
be deleted and reset to the device's default
state by setting the value of this object to
'true(1)'. The value 'false(2)' will al… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.45.4.7.1.11.3 |
| ntnQosConfigTrackStatistics The value of this attribute determines if
statistics tracking is enabled for system-level
policies. System-level policies are created to
enforce the default QoS processing rules
a… | scalar | Enumeration | .1.3.6.1.4.1.45.4.7.1.11.4 |
| ntnQosConfigNVCommitDelay Specifies the maximum amount of time, in seconds,
before non-volatile QoS configuration data will be
written to non-volatile storage. Delaying NV access
can be used to minimize fi… | scalar | seconds SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.45.4.7.1.11.5 |
| ntnQosConfigDefaultQueueCfg The value of this attribute determines the queue
set that is associated with all egress interfaces
by default.
A queue set is characterized by the number of
queues in t… | scalar | Enumeration | .1.3.6.1.4.1.45.4.7.1.11.6 |
| ntnQosConfigUBPSupportLevel Determines whether QoS Agent User Based Policy
(UBP) support is enabled and, if so, what level
of support is enabled. Setting the value of this
attribute to 'ubpSupportDisabled(… | scalar | Enumeration | .1.3.6.1.4.1.45.4.7.1.11.8 |
| ntnQosConfigRoleAssocCompatLevel Determines whether interface role associations
are subject to loose or strict capabilities
verification. Setting the value of this attribute
to 'roleAssocCompatLoose(1)' means tha… | scalar | Enumeration | .1.3.6.1.4.1.45.4.7.1.11.9 |