portFrGenClock
NETLINK-SPECIFIC-MIB ·
.1.3.6.1.4.1.173.7.3.2.1.1.10
Object
column
mandatory
r/w
Enumeration
This specifies whether the port will generate the clock necessary to synchronize traffic over the link.
Context
- MIB
- NETLINK-SPECIFIC-MIB
- OID
.1.3.6.1.4.1.173.7.3.2.1.1.10- Type
- column
- Access
- readwrite
- Status
- mandatory
- Parent
- portFrEntry
- Table
- portFrConfigTable
- Siblings
- 14
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | no |
2 | yes |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| portFrRlpIndex mandatory The RLP number of the Frame Relay port. It will be in the
range 1-8. | column | Integer32 | .1.3.6.1.4.1.173.7.3.2.1.1.1 |
| portFrRcvClkFrmDTE mandatory This allows the clock to be looped back from the DTE using
the TT (Terminal Timing) signal, which can be helpful on
high-speed lines. | column | Enumeration | .1.3.6.1.4.1.173.7.3.2.1.1.11 |
| portFrLLM mandatory This determines whether, and what type of, configurable
network management (status enquiries) will be allowed. | column | Enumeration | .1.3.6.1.4.1.173.7.3.2.1.1.12 |
| portFrRowStatus mandatory This variable is used to manage the creation and deletion
of conceptual rows in the portFrConfigTable and follows the
SNMPv2 RowStatus conventions by supporting the following valu… | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.173.7.3.2.1.1.13 |
| portFrSpeed mandatory This object defines the speed of the Frame Relay port. The speed may
only be set to one of a series of reasonable values, and if an attempt is made
to set the speed to a value wh… | column | Integer32 | .1.3.6.1.4.1.173.7.3.2.1.1.14 |
| portFrBackupUseOnly mandatory This object determines whether all DLCIs on the port will
be reserved exclusively as backups for other DLCIs in the
same node. If yes is specified for this object, the port
will r… | column | Enumeration | .1.3.6.1.4.1.173.7.3.2.1.1.15 |
| portFrPortIndex mandatory The Port number of the Frame Relay port. It will
be in the range 1-8 for a physical port. It will be in the range
9-64 for a Frame Relay logical port. | column | Integer32 | .1.3.6.1.4.1.173.7.3.2.1.1.2 |
| portFrBlockedFlag mandatory A flag which when set, means the port should not be
enabled after a boot-up of the node. | column | Enumeration | .1.3.6.1.4.1.173.7.3.2.1.1.3 |
| portFrMaxBytesPerFrame mandatory The maximum number of bytes allowed in an I Frame for this
Frame Relay port. | column | Integer32 | .1.3.6.1.4.1.173.7.3.2.1.1.4 |
| portFrT392Timer mandatory This timer indicates how long the network will wait between
Status Enquiry messages before recording an error. It
should be greater than or equal to the frDlcmiPollingInterval
va… | column | Integer32 | .1.3.6.1.4.1.173.7.3.2.1.1.5 |
| portFrOutgoingRateControl mandatory This is a flag which, when set, enables the enforcement of
the Outgoing Rate Control parameters. | column | Enumeration | .1.3.6.1.4.1.173.7.3.2.1.1.6 |
| portFrBandwidthAllocation mandatory This is a flag which, when set, enables whether the bandwidth
allocation will be enforced. | column | Enumeration | .1.3.6.1.4.1.173.7.3.2.1.1.7 |
| portFrConnector mandatory This defines the connector type of the Frame Relay port. | column | Enumeration | .1.3.6.1.4.1.173.7.3.2.1.1.8 |
| portFrLogicalDCE mandatory This defines the port as logical DCE or DTE. | column | Enumeration | .1.3.6.1.4.1.173.7.3.2.1.1.9 |