mesErpHoldOffTime
LUM-MES-MIB ·
.1.3.6.1.4.1.8708.2.32.2.26.1.1.12
Object
column
r/w
Unsigned32
A hold-off timer coordinates timing of protection
switches between multiple layers. The timer gives
another protection layer the possibility to solve
the issue before performing the protection
switch. When a signal fail event occurs, this event
is not reported until the hold-off timer has elapsed.
The hold-off time is defined in steps of
100 milliseconds.
Note! A non-zero hold-off time will impact the
protection switch time performance.
Context
- MIB
- LUM-MES-MIB
- OID
.1.3.6.1.4.1.8708.2.32.2.26.1.1.12- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- mesErpEntry
- Table
- mesErpTable
- Siblings
- 48
Syntax
Unsigned32
Values & Constraints
Object Constraints
range: 0-10000
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| mesErpIndex An arbitrary index. Subrack, slot and VLAN ID can
be derived from the index. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.32.2.26.1.1.1 |
| mesErpProtLink The direction towards the Ring Protection Link (RPL) and the role of the node.
For the owner the RPL is situated on the chosen port while for the neighbour the
specified port is c… | column | Enumeration | .1.3.6.1.4.1.8708.2.32.2.26.1.1.10 |
| mesErpGuardTime The guard time is used to protect from receiving
old R-APS messages during a recovery from a failed
link. When the guard timer is running, all received
R-APS messages are ignored.… | column | Unsigned32 | .1.3.6.1.4.1.8708.2.32.2.26.1.1.11 |
| mesErpWtrTime After the link has recovered from a failure, the RPL
owner waits a fixed period before
blocking the RPL and restoring it to idle state.
The wait to restore time is defined in minu… | column | Unsigned32 | .1.3.6.1.4.1.8708.2.32.2.26.1.1.13 |
| mesErpOamDetectionLeft Defines whether OAM signal failure detection is
enabled on the left ERP port. | column | Enumeration | .1.3.6.1.4.1.8708.2.32.2.26.1.1.14 |
| mesErpOamDetectionRight Defines whether OAM signal failure detection is
enabled on the right ERP port. | column | Enumeration | .1.3.6.1.4.1.8708.2.32.2.26.1.1.15 |
| mesErpStatusLeft Indicates if the left ERP port forwards or blocks
traffic. | column | Enumeration | .1.3.6.1.4.1.8708.2.32.2.26.1.1.16 |
| mesErpStatusRight Indicates if the right ERP port forwards or blocks
traffic. | column | Enumeration | .1.3.6.1.4.1.8708.2.32.2.26.1.1.17 |
| mesErpProtState Indicates the protection state of the ring.
Starting
- The ring is in start-up phase.
Idle
- No failure has been detected and the Ring
Pro… | column | Enumeration | .1.3.6.1.4.1.8708.2.32.2.26.1.1.18 |
| mesErpActiveEvent Information about latest input to the ERP state machine. | column | Enumeration | .1.3.6.1.4.1.8708.2.32.2.26.1.1.19 |
| mesErpName The management name of the ERP.
For ERP V1:
'erp:1:5:4094' (erp:[subrack]:[slot]:[vlanId])
For ERP V2:
'erp2:1:5:1:4094' (erpv2:[subrack]:[slot]:[ringId]:[vlanId]). | column | LUM-TCMgmtNameString | .1.3.6.1.4.1.8708.2.32.2.26.1.1.2 |
| mesErpRapsReqState Request in the latest sent or received R-APS message. | column | Enumeration | .1.3.6.1.4.1.8708.2.32.2.26.1.1.20 |
| mesErpServiceFailure New signal failure detected while in protected
state. I.e. two or more faults in the ring. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.32.2.26.1.1.21 |
| mesErpServiceDegraded The ERP is in protection state. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.32.2.26.1.1.22 |
| mesErpUnexpectedMegLevel Invalid R-APS messages received. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.32.2.26.1.1.23 |
| mesErpCommunicationFailure An expected R-APS message has not been received in
the last 15 second period. dFOP-TO in G.8032. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.32.2.26.1.1.24 |
| mesErpChangePort deprecated Procedure to change left and right port and
protection link. This functionality
is only available for ERPv1. | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.32.2.26.1.1.25 |
| mesErpRowStatus Manages creation and deletion of conceptual rows.
See also SNMPv2-TC.
Note: The newly created object will not necessarily
receive the same index as used in the crea… | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.8708.2.32.2.26.1.1.26 |
| mesErpNodeType The type of the ERPV2 node.
Ring node - Standard ring node.
Sub Interconnection - Node that connects a sub ring to a major ring. | column | Enumeration | .1.3.6.1.4.1.8708.2.32.2.26.1.1.27 |
| mesErpProtectionMode The protection mode of the ERPv2 instance.
nonRevertive -- non-revertive mode
revertive -- revertive mode | column | Enumeration | .1.3.6.1.4.1.8708.2.32.2.26.1.1.28 |
| mesErpVersion The protocol version of the ERP instance.
erpV1 -- ERPv1
erpV2 -- ERPv2 | column | Enumeration | .1.3.6.1.4.1.8708.2.32.2.26.1.1.29 |
| mesErpPortLeft The interface (Tx-Rx) where the left ERP link is located. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.32.2.26.1.1.3 |
| mesErpMajorName The management name of the major ring that the
subring is connected to.
For example
'erp2:1:5:1:4094' (erp:[subrack]:[slot]:[ringId]:[vlanId]). | column | LUM-TCMgmtNameString | .1.3.6.1.4.1.8708.2.32.2.26.1.1.30 |
| mesErpRingId Ring ID for the ERPv2 instance. All ERP instances
must have the same ring ID throughout the ERP ring. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.32.2.26.1.1.31 |
| mesErpRingIndex Index of ring used by VLAN Protection Groups and
VLAN Map when referring to a ring. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.32.2.26.1.1.32 |
| mesErpOperatorCommand The operator commands.
noRequest (1)
-- initial state and the return state after issuing an operator command.
forced left (2)
-- force a block on the left ring port where th… | column | Enumeration | .1.3.6.1.4.1.8708.2.32.2.26.1.1.33 |
| mesErpGroupId Unique number identifying group VLAN protection group for the R-APS VLAN of this ring. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.32.2.26.1.1.34 |
| mesErpSwitchInformation User has set a manual or a forced ERP switch. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.32.2.26.1.1.35 |
| mesErpTopologyChangePropagation Disable or enable forwarding of topology change from sub-ring to major ring. | column | Enumeration | .1.3.6.1.4.1.8708.2.32.2.26.1.1.36 |
| mesErpSubRings List of Ring Indexs of connected ERP v2 sub rings, | column | SNMPv2-SMICounter64 | .1.3.6.1.4.1.8708.2.32.2.26.1.1.37 |
| mesErpResourceTypeLeft The type of resource the left leg of erp is connected. | column | Enumeration | .1.3.6.1.4.1.8708.2.32.2.26.1.1.38 |
| mesErpLagIdLeft Id of the left lag connected to erp. | column | OctetString | .1.3.6.1.4.1.8708.2.32.2.26.1.1.39 |
| mesErpPortRight The interface (Tx-Rx) where the right ERP link is located. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.32.2.26.1.1.4 |
| mesErpResourceTypeRight The type of resource the right leg of erp is connected. | column | Enumeration | .1.3.6.1.4.1.8708.2.32.2.26.1.1.40 |
| mesErpLagIdRight Id of the right lag connected to erp. | column | OctetString | .1.3.6.1.4.1.8708.2.32.2.26.1.1.41 |
| mesErpInterfaceLeft Displayname for the left interface connected to erp. | column | OctetString | .1.3.6.1.4.1.8708.2.32.2.26.1.1.42 |
| mesErpInterfaceRight Displayname for the right interface connected to erp. | column | OctetString | .1.3.6.1.4.1.8708.2.32.2.26.1.1.43 |
| mesErpProvisioningMismatch Detected if the RPL owner receives one or more
No request R-APS message(s) with the RPL blocked status flag
set (NR, RB) and a node ID that differs from its own. dFOP-PM in G.8032. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.32.2.26.1.1.44 |
| mesErpIfNoLeft The left interface number of the multi-connector port or port group. | column | LUM-TCPortNumber | .1.3.6.1.4.1.8708.2.32.2.26.1.1.45 |
| mesErpTxPortLeft The TX-port of the left interface. | column | LUM-TCPortNumber | .1.3.6.1.4.1.8708.2.32.2.26.1.1.46 |
| mesErpIfNoRight The right interface number of the multi-connector port or port group. | column | LUM-TCPortNumber | .1.3.6.1.4.1.8708.2.32.2.26.1.1.47 |
| mesErpTxPortRight The TX-port of the right interface. | column | LUM-TCPortNumber | .1.3.6.1.4.1.8708.2.32.2.26.1.1.48 |
| mesErpOamDetectionVlanId The VLAN ID in CCM:s used for OAM detection. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.32.2.26.1.1.49 |
| mesErpAdminStatus The administrative state for the object.
service - The object is activated but alarms
are suppressed. Intended for use during service
or re-configuration. When serv… | column | LUM-TCBoardOrInterfaceAdminStatus | .1.3.6.1.4.1.8708.2.32.2.26.1.1.5 |
| mesErpInternalReference For internal use only. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.32.2.26.1.1.6 |
| mesErpDescr User configurable label. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.32.2.26.1.1.7 |
| mesErpVlanId All control messaging (R-APS channel) for the ring are transmitted
on a specific VLAN ID. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.32.2.26.1.1.8 |
| mesErpMegLevel The Maintenance Domain Level (or MEG Level). The MEG level must be the same
across all ERP instances in the same ERP ring. | column | Dot1agCfmMDLevel | .1.3.6.1.4.1.8708.2.32.2.26.1.1.9 |