clientIfJitterAttenuatorBW
LUM-CLIENT-MIB ·
.1.3.6.1.4.1.8708.2.27.2.2.1.1.108
Object
column
r/w
Enumeration
Determines the wander/jitter transfer bandwidth
of the wander/jitter attenuator.
With Option 1, the bandwidth is within 1 - 10 Hz,
and with Option 2, the bandwidth is below 0.1 Hz.
The values are defined according to
- G.813 for SDH, and
- G.8262 for synchronous ethernet
Context
- MIB
- LUM-CLIENT-MIB
- OID
.1.3.6.1.4.1.8708.2.27.2.2.1.1.108- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- clientIfEntry
- Table
- clientIfTable
- Siblings
- 154
Syntax
Enumeration
Values & Constraints
Enumerated Values
0 | option1 |
1 | option2 |
2 | notUsed |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| clientIfIndex An arbitrary index assigned to each entry. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.1 |
| clientIfAdminStatus The administrative state for the interface.
down - The interface is de-activated.
service - The interface is activated but alarms are
suppressed. Int… | column | LUM-TCBoardOrInterfaceAdminStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.10 |
| clientIfFormatNotSupportedByHw The HW revision does not support
the selected signal format. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.100 |
| clientIfLaserMode The administrative state of the TX-side laser.
This is only used when signal format is ddgbeLine.
on - The laser is turned on.
als - Automatic Laser … | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.101 |
| clientIfAlarmIndicationSignalLineC2W Alarm indication signal Line (AIS-L) on the
client side.
Applicable for Sonet signal formats.
A: An 'all ones' Sonet signal is detected.
D: Sonet sig… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.102 |
| clientIfFarEndClientFailure Failure on far end client. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.103 |
| clientIfOHTransparency The 'OH Transparency' setting shall be set to 'off'
for standard SDH/SONET mode. Does not work when
client wrapper is enabled.
When set to 'on', the following tribu… | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.104 |
| clientIfConnectedLine The line ports that this client port is connected to. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.105 |
| clientIfForwardingErrorCorrectionMode The administrative state of the forwarding error
correction function.
disabled - FEC is disabled.
enabled - FEC is activated.
auto - a… | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.106 |
| clientIfNoFrequencySet The tunable laser frequency has not been set.
A: Tunable laser frequency is not set.
D: Tunable laser frequency is set. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.107 |
| clientIfConnectionStatus Shows the name of the wdm port and
possible subchannel/vc4 that it is connected to
or Unconnected if not connected. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.27.2.2.1.1.109 |
| clientIfOperStatus The operational state for the interface.
notPresent - The physical resources are not
available.
down - The interface is de-activated or there are
fau… | column | LUM-TCBoardOrInterfaceOperStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.11 |
| clientIfLoopFilterUnlocked The loopfilter is unlocked.
This is applicable for synchronous formats.
A: Loopfilter is unlocked
D: Loopfilter is locked | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.110 |
| clientIfCableLength The 'Cable length' is applicable for SONET mode
(T1).
The settings are for short haul (intra-building) T1
networks and will adjust the power of the
transmitted s… | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.111 |
| clientIfConnectedForeignIndex Shows the index of the connected interface.
Or 0 if unconnected. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.112 |
| clientIfDisconnect Disconnect existing crossConnections | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.27.2.2.1.1.113 |
| clientIfOHTransparencyBitMask The OH transparency bitmask.
Bits:
K1K2 = 0x01
E1E2 = 0x02
F1 = 0x04
D1-D3 = 0x08
D4-D12 = 0x10
B1 = 0x20
B2 = 0x40
E1 = 0x80
E2 = 0x100
J0 = 0x200 | column | Unsigned32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.114 |
| clientIfOHTransparencyString OH transparency bytes tells if J0, rest
of RSOH/Section OH and/or MSOH/Line OH are
transparent or not.
When RSOH/Section OH is set to transparent the bytes
E1, F1, D1-D3 and B1 is… | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.27.2.2.1.1.115 |
| clientIfOHTransparencySet Set which bytes that should be OH transparent | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.27.2.2.1.1.116 |
| clientIfAuAlarmIndicationSignalC2W Alarm indication signal (AIS) on the
client-side.
Applicable for SDH/Sonet signal formats.
A: An 'all ones' SDH signal is detected.
D: SDH signal rec… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.117 |
| clientIfAuLossOfPointerC2W Loss of pointer detected on the client-side.
Applicable for SDH/Sonet signal formats.
A: A loss of pointer is detected.
D: SDH signal recovered. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.118 |
| clientIfAuLossOfPointerW2C Loss of pointer detected on the line-side.
Applicable for SDH/Sonet signal formats.
A: A loss of pointer is detected.
D: SDH signal recovered. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.119 |
| clientIfLaserStatus The operational state of the laser.
off - The laser is turned off.
on - The laser is turned on. | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.12 |
| clientIfEthStandbyIndicator Shows if this port is in standby state.
Used with hub protection. | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.120 |
| clientIfAuAlarmIndicationSignalW2CSonet Alarm indication signal (AIS-P) on the line-side.
A: An 'all ones' Sonet signal is detected.
D: Sonet signal recovered. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.121 |
| clientIfAuAlarmIndicationSignalC2WSonet Alarm indication signal (AIS-P) on the
client-side.
A: An 'all ones' Sonet signal is detected.
D: Sonet signal recovered. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.122 |
| clientIfAuLossOfPointerC2WSonet Loss of pointer detected on the client-side.
A: A loss of pointer is detected.
D: Sonet signal recovered. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.123 |
| clientIfAuLossOfPointerW2CSonet Loss of pointer detected on the line-side.
A: A loss of pointer is detected.
D: Sonet signal recovered. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.124 |
| clientIfTransceiverNoLoopback The inserted transceiver does not support
the given loopback command. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.125 |
| clientIfFecFailure Too many errors to get valid FEC statistics. It is not
possible to run control loops based on FEC statistics.
A: Too many errors to get valid FEC statistics.
… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.126 |
| clientIfLaneAlignmentError Indicates whether multi-lane
BASE-R PCS (Physical Coding Sublayer)
has locked and aligned all received lanes.
A: PCS receive lanes not locked and aligned.
… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.127 |
| clientIfFecCorrectedZeros The number of corrected zeros. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.128 |
| clientIfFecCorrectedOnes The number of corrected ones. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.129 |
| clientIfTxSignalStatus The operational state for outgoing (TX) signal
of the interface.
down - A fault that would lead to a protection
switch has occurred.
degraded - The s… | column | LUM-TCSignalStatusWithNA | .1.3.6.1.4.1.8708.2.27.2.2.1.1.13 |
| clientIfSignalDegraded Too many error corrected.
If more errors are corrected
it might effect the client signal
in a negative way. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.130 |
| clientIfFecType Set FEC scheme.
disabled -- none specific FEC scheme is enabled.
gFec -- GFEC RS(255,239) FEC scheme,
according to ITU.T G.975
superFecI4 -- Super FEC I.4 FE… | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.131 |
| clientIfSignalDegradeThreshold The alarm Signal Degraded shall be signalled
when BER reaches a limit.
The value will be affecting all ports.
Predefined BER levels
rxBerLevel1 = 1E-12
rxBerLevel2 … | column | LUM-TCBerLevelMTOSI | .1.3.6.1.4.1.8708.2.27.2.2.1.1.132 |
| clientIfExpectedOpticalLayerMapping The expected optical layer mapping. | column | LUM-TCOpticalLayerMappingType | .1.3.6.1.4.1.8708.2.27.2.2.1.1.133 |
| clientIfActualOpticalLayerMapping The actual optical layer mapping. | column | LUM-TCOpticalLayerMappingType | .1.3.6.1.4.1.8708.2.27.2.2.1.1.134 |
| clientIfConfigurationMismatch The inserted transceiver does not support the
configuration of the optical layer mapping.
A: A transceiver with other supported optical layer
mapping than the re… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.135 |
| clientIfChromaticDispersion Received chromatic dispersion that describe the spreading of a light
pulse as it travels down a fiber when light pulses launched close together. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.136 |
| clientIfDifferentialGroupDelay The arrival time difference between two polarization states at
the output of the media (fiber). | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.137 |
| clientIfTxState The operational state of the transiver for outgoing (TX) signal.
- Init started
- Init ready
- Data path locked
- Laser ready off
- Laser ready
- Laser bias ready
- Ready | column | LUM-TCTrxTxState | .1.3.6.1.4.1.8708.2.27.2.2.1.1.138 |
| clientIfRxState The operational state of the transiver for outgoing (RX) signal.
- Init started
- Init ready
- Frequency ready
- Input signal received
- A/D Converter ready
- Dispersion compensat… | column | LUM-TCTrxRxState | .1.3.6.1.4.1.8708.2.27.2.2.1.1.139 |
| clientIfForwardAls Forward Automatic Laser Shut-down. Decides if
laser shutdown of the client should occur when
a defect on the line or remote client is detected.
disabled - The laser… | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.14 |
| clientIfIdx Internal object reference | column | Integer32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.140 |
| clientIfIfNo The physical interface number of the actual multi-connector port. | column | LUM-TCPortNumber | .1.3.6.1.4.1.8708.2.27.2.2.1.1.141 |
| clientIfIdxIf Internal object reference of the actual multi-connector port. | column | Integer32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.142 |
| clientIfUpPortId Internal port reference for traffic unit. | column | Integer32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.143 |
| clientIfNoOfLanes Number of lanes on port | column | Integer32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.144 |
| clientIfFecCorrectedBits FEC counter. Number of corrected bits | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.145 |
| clientIfOSNRMargin Optical signal-to-noise ratio margin (dB/0.1nm), based on calculation from rate of corrected bits. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.146 |
| clientIfExpectedPhysicalLayerMapping The expected physical layer mapping. | column | LUM-TCPhysicalLayerMappingType | .1.3.6.1.4.1.8708.2.27.2.2.1.1.147 |
| clientIfSignalDirection Indicates the direction of the signal.
rx - Inbound direction
tx - Outbound direction
biDir - Bidirectional
txRx … | column | LUM-TCSignalDirection | .1.3.6.1.4.1.8708.2.27.2.2.1.1.148 |
| clientIfAid The access identifier (AID) of the interface.
The format is according to GR-833. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.27.2.2.1.1.149 |
| clientIfSuppressRemoteAlarms Suppress AIS in the alarm list.
The fault status on the port object can, however,
be seen.
disabled - alarms are not suppressed.
enabled - alarms are… | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.15 |
| clientIfPhysicalLocation The physical location of the if.
The format is according to GR-833. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.27.2.2.1.1.150 |
| clientIfTrxCommunicationFailure The board is unable to communicate with the transceiver.
alarm: Protocol errors detected on the transceiver control link.
ok: No communication errors… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.151 |
| clientIfTribPortId Tributary port id. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.152 |
| clientIfIfType Type of interface (Individual or bundled). | column | LUM-TCInterfaceType | .1.3.6.1.4.1.8708.2.27.2.2.1.1.153 |
| clientIfConfigurationCommandSNMP Command to change the signal format, and, if
applicable, also the mode (framed, transparent) via SNMP. | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.27.2.2.1.1.154 |
| clientIfTrxPowerOutOfRange The power classification of the transceiver exceeds the design limit of the board.
alarm: A transceiver with a power classification that exceeds
the design l… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.155 |
| clientIfFarEndLoopback Loop the client TX signal back to the client RX.
This is also called Terminal loopback.
disabled - the signal is not looped
enabled - the signal is l… | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.16 |
| clientIfFormat The expected signal format.
The default value is board dependent. For information
about the default value for this particular board,
please refer to the user manual. | column | LUM-TCSignalFormat | .1.3.6.1.4.1.8708.2.27.2.2.1.1.17 |
| clientIfGfpMode Generic framing procedure mode | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.18 |
| clientIfBandWidth Band-width in VC-3 or VC-4.
The parameter is interpreted as VC-3 or VC-4
depending on the traffic combination:
- VC-3 is used in framedGbEx10
- VC-4 … | column | Integer32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.19 |
| clientIfName The management name of the interface, for
example 'client:1:2:1', where the first number
indicates sub-rack, the second slot number and
the third is the port number.
Examples:
… | column | LUM-TCMgmtNameString | .1.3.6.1.4.1.8708.2.27.2.2.1.1.2 |
| clientIfRateLimit Rate limit of link in 1,000,000 bits
(Mb) per second.
Zero (0) is a special value meaning that the
rate-limiting procedure is disabled.
The legal ran… | column | Integer32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.20 |
| clientIfAutoNegotiationMode The wanted auto negotiation mode.
off - auto negotiation process is disabled
on - auto negotiation process is enabled | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.21 |
| clientIfAutoNegotiationStatus The result of the auto negotiation procedure
incomplete - the result is still pending
half - half duplex
full - full duplex | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.22 |
| clientIfDuplexCapability The duplex capability of the HW.
half - supports half duplex
full - supports full duplex | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.23 |
| clientIfFlowControlMode The mode for handling flow control between
the local device and link partner.
The PAUSE settings has the following meaning
when auto-negotiation is enabled.
… | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.24 |
| clientIfInterPacketGap Time between the frames in nano seconds.
Legal values are 64, 72, 80, ... 200, 320, 328,
336, ... 456 | column | Unsigned32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.25 |
| clientIfFrameSize The maximum size of the transmitted and
received frames (in bytes). | column | Unsigned32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.26 |
| clientIfTrxClass String that describes the transceiver class. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.27.2.2.1.1.27 |
| clientIfLaserBias Measures laser bias current value in tenths of
mA (0.1 mA). | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.28 |
| clientIfPowerLevel The received power level in units of 0.1 dBm. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.29 |
| clientIfDescr User configurable label.
This attribute can be written via SNMP. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.27.2.2.1.1.3 |
| clientIfReceiverSensitivity The lowest power that the receiver is guaranteed
to handle, in units of 0.1 dBm. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.30 |
| clientIfPowerLevelLowRelativeThreshold The lower threshold for received power level in
units of 0.1 dB, relative to the receiver
sensitivity. | column | Integer32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.31 |
| clientIfLossOfSignal Loss of signal.
Applicable for all signal formats.
A(ctivation): Active loss of signal HW
indication.
D(e-activation): Inactive loss of signal HW
ind… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.32 |
| clientIfLossOfFrame Loss of frame.
All forms of sync loss. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.33 |
| clientIfBitrateMismatch Bitrate mismatch (Other).
Applicable for other signal formats.
D: The interface is unable to lock to the
inserted signal.
D: The interface is able to… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.34 |
| clientIfAuAlarmIndicationSignalW2C Alarm indication signal (AIS) on the trunk-side.
Applicable for SDH/Sonet signal formats.
A: An 'all ones' SDH signal is detected.
D: SDH signal reco… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.35 |
| clientIfTransmitterFailed The transceiver HW has detected a failure
in the transmitter part.
A: The transmitter has failed
D: The transmitter is OK again | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.36 |
| clientIfTrxCodeMismatch The inserted transceiver does not have a legal
manufacturer code.
A: A transceiver with illegal code is inserted.
D: The transceiver with illegal cod… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.37 |
| clientIfTrxBitrateUnavailable The inserted transceiver does not support the
requested bit rate.
A: A transceiver with other supported bit rate than
the requested bit rate is inserted.
… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.38 |
| clientIfTrxMissing An expected transceiver is missing.
A: An expected transceiver is missing.
D: The missing transceiver is inserted. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.39 |
| clientIfSubrack The number of the subrack where the interface
is located. | column | LUM-TCSubrackNumber | .1.3.6.1.4.1.8708.2.27.2.2.1.1.4 |
| clientIfReceivedPowerHigh Received power level is too high.
Applicable for all signal formats.
A: The received power level exceeds the
the built-in overload threshold.
D: The … | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.40 |
| clientIfReceivedPowerLow Received power level low threshold exceeded.
Applicable for all signal formats.
A: The received power level is below the
associated threshold.
D: The… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.41 |
| clientIfLinkDown A: Failure to negotiate a connection with the
other party.
D: A connection is negotiated. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.42 |
| clientIfConfigurationCommand Command to change the signal format, and, if
applicable, also the mode (framed, transparent). | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.27.2.2.1.1.43 |
| clientIfGbeUtilization Shows the current bandwidth utilization
measured at the physical (802.3 PHY) layer.
The value represents a snapshot of the utilization
during the latest second. It is expressed i… | column | Unsigned32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.44 |
| clientIfLossOfSync Loss of sync.
All forms of sync loss.
A: GbE 'frame' can not be located.
D: GbE 'frame' is located. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.45 |
| clientIfConfigureTrxModeCommand Command to change the TRX mode (client or line) and/or
TRX media (optical or electrical). | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.27.2.2.1.1.46 |
| clientIfTrxMode Shows if the port is configured as:
- normal CLIENT interface connected to a non XTM Series
client equipment, with non-colored, or colored TRXes.
-… | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.47 |
| clientIfExpectedTxFrequency The expected frequency given in hundreds of GHz
(0.01 GHz). | column | LUM-TCLambdaFrequency | .1.3.6.1.4.1.8708.2.27.2.2.1.1.48 |
| clientIfTxFrequency The transmitted frequency given in hundreds of
GHz (0.01 GHz). | column | LUM-TCLambdaFrequency | .1.3.6.1.4.1.8708.2.27.2.2.1.1.49 |
| clientIfSlot The number of the slot where the interface is
located. | column | LUM-TCSlotNumber | .1.3.6.1.4.1.8708.2.27.2.2.1.1.5 |
| clientIfUnexpectedTxFrequency The actual frequency does not match the
pre-configured frequency.
A pre-configured frequency of '0' matches
all actual frequencies.
A: The configured… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.50 |
| clientIfIllegalFrequency The frequency supported by the transceiver is not
recognized by the system.
A: Invalid or unknown frequency information is
detected in the (pluggable) transceive… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.51 |
| clientIfLaserForcedOn When enabled, the laser is on regardless of whether
there is a trunc signal present or not.
disabled - the laser is only on when there is a
trunc signal.… | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.52 |
| clientIfTrxMedia Defines the media and capability of the TRX. | column | LUM-TCTrxMedia | .1.3.6.1.4.1.8708.2.27.2.2.1.1.53 |
| clientIfTrxMediaMismatch The TRX media does not match the expected one.
A: Invalid or mismatching trx media is
detected.
D: The (pluggable) transceiver or board is
repl… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.54 |
| clientIfTruncAutoNegotiationMode Decides whether auto negotiation shall
be performed over the trunc connection.
This is applicable when the terminating
node at the other side of the
trunc is config… | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.55 |
| clientIfObjectProperty Property mask. | column | LUM-TCObjectProperty | .1.3.6.1.4.1.8708.2.27.2.2.1.1.56 |
| clientIfTxPowerLevel The transmitted power level in units of 0.1 dBm. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.57 |
| clientIfLaserTempActual The actual laser temperature in units of
0.1 degrees centigrade. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.58 |
| clientIfTraceIntrusionMode Indicates whether the trace identifier should be
inserted into the transmitted signal or to be
transparent.
disabled - The trace identifier is taken from
the recevi… | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.59 |
| clientIfTxPort The number of the port where the TX-side of the
interface is located. | column | LUM-TCPortNumber | .1.3.6.1.4.1.8708.2.27.2.2.1.1.6 |
| clientIfTraceTransmitted The trace identifier to be transmitted from this
interface.
The identifier length is by default 0 to 15. For
mxp8iiSonet board the length i 0 to 62.
… | column | OctetString | .1.3.6.1.4.1.8708.2.27.2.2.1.1.60 |
| clientIfTraceReceived The received trace identifier for this interface. | column | OctetString | .1.3.6.1.4.1.8708.2.27.2.2.1.1.61 |
| clientIfTraceExpected Trace identifier used for matching against
the received trace identifier.
The identifier length is by default 0 to 15. For
mxp8iiSonet board the length is 0 to 62. | column | OctetString | .1.3.6.1.4.1.8708.2.27.2.2.1.1.62 |
| clientIfTraceAlarmMode Controls if the trace identifier mismatch alarm
should be raised.
disabled - The alarm is disabled.
enabled - The alarm is raised if expected trace
i… | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.63 |
| clientIfTraceMismatch Indicates if the expected trace identifier
differs from the received trace identifier.
A: The received trace identifier differs from
the expected trace identifier.
… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.64 |
| clientIfNearEndLoopback Loop the client RX signal back to the client TX.
This is also called Facility loopback
disabled - the signal is not looped
enabled - the signal is lo… | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.65 |
| clientIfRxSignalStatus The operational state for incoming (RX) signal
of the interface.
down - A major fault has occurred
degraded - The signal quality is impaired.
… | column | LUM-TCSignalStatusWithNA | .1.3.6.1.4.1.8708.2.27.2.2.1.1.66 |
| clientIfMsAlarmIndicationSignalC2W MS Alarm indication signal (MS-AIS) on the
client side.
Applicable for SDH/Sonet signal formats.
A: An 'all ones' pattern is detected.
D: The signal … | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.67 |
| clientIfMsAlarmIndicationSignalW2C MS Alarm indication signal (MS-AIS) on the trunc
side. Applicable for SDH/Sonet/IWDM signal formats.
A: An 'all ones' pattern is detected.
D: The sig… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.68 |
| clientIfRemoteDefectIndication Remote defect indication.
Applicable for SDH/Sonet signal formats.
A: RDI indication (in SDH/Sonet frame) active.
D: RDI indication inactive. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.69 |
| clientIfRxPort The number of the port where the RX-side of the
interface is located. | column | LUM-TCPortNumber | .1.3.6.1.4.1.8708.2.27.2.2.1.1.7 |
| clientIfJ1TxTrailTrace The J1 trail trace identifier(s) to be
transmitted for the VC4s/VC3s related to this
interface, in the line signal (STM16/OC48).
This parameter can be used in two d… | column | OctetString | .1.3.6.1.4.1.8708.2.27.2.2.1.1.70 |
| clientIfJ1TxTrailTraceInsertionMode Controls how the J1 trail trace insertion
should work, i.e. how the j1TxTrailTrace
parameter shall be inserted in the line
signal.
Important: there is only one j1Tx… | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.71 |
| clientIfTrxFailed A transceiver hardware failure is detected.
A: The transceiver fails.
D: The transceiver is replaced. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.72 |
| clientIfDisabled The interface is disabled.
A: Interface disabled.
D: Interface enabled. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.73 |
| clientIfLoopback The interface is set in loopback mode.
A: Loopback enabled.
D: Loopback disabled. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.74 |
| clientIfVcGroupFailedW2C The received line signal contains a VC
mapped to this interface, that is
faulty, e.g. unequipped.
Please note that this fault is in the
LINE SIGNAL, but is presente… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.75 |
| clientIfReadJ1 Read the received J1 for the VC4/VC3 in the
STM16 frame associated to this interface.
Synopsis: readJ1 | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.27.2.2.1.1.76 |
| clientIfClientSignalFailed The received line signal contains a VC
mapped to this interface, that is
faulty, e.g. unequipped.
Please note that this fault is in the
LINE SIGNAL, but is presente… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.77 |
| clientIfAuLossOfPointer Loss of pointer. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.78 |
| clientIfGfpLossOfFrame GFP Loss of frame. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.79 |
| clientIfInvPhysIndexOrZero The row in the invPhysTable for this interface.
Set to 0 if not known. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.8 |
| clientIfHighSpeed The expected signal bit rate in units of
1,000,000 bits (Mb) per second. If this object
reports a value of 'n' then the speed of the
interface is somewhere in the range of 'n-500,… | column | Unsigned32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.80 |
| clientIfActualFormat The actual signal format. | column | LUM-TCSignalFormat | .1.3.6.1.4.1.8708.2.27.2.2.1.1.81 |
| clientIfRdiIntrusionMode Indicates whether RDI information should be
inserted in the transmitted signal.
disabled - No RDI information is inserted in the
transmitted signal.
… | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.82 |
| clientIfMuxQuadVc4 States which quadrant of the payload
that the interface is connected to
in rx direction. (outgoing line) | column | Unsigned32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.83 |
| clientIfDemuxQuadVc4 States whitch quadrant of the payload
that the interface is connected to
in tx direction. (outgoing client) | column | Unsigned32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.84 |
| clientIfCcConnectionMode controls if DemuxPayloadQuad is same
as MuxPayloadQuad
(same => connected, not same => disconnected) | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.85 |
| clientIfCcConfigurationCommand Command to change the crossconnect,
If no arguments are given, the user will be prompted. | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.27.2.2.1.1.86 |
| clientIfIllegalSignalFormat IllegalSignalFormat.
A(ctivation): Actual Format does NOT match
expected Format.
D(e-activation): Actual Format does match
expected Format. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.87 |
| clientIfSynchProtPortId The Id for this port in the synch prot group,
to identify the port. (A or B) | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.88 |
| clientIfSynchProtGroupMemberPort The port number for the TX side of the port
that is in this synch protection group. | column | LUM-TCPortNumber | .1.3.6.1.4.1.8708.2.27.2.2.1.1.89 |
| clientIfEntityId Index in entity table.
-- Only used for notifications | column | Unsigned32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.9 |
| clientIfSynchProtGroupStatus Note: This object is deprecated.
The operational state for the protection group.
bothDown - both sides down
bothUp - both sides up
… | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.90 |
| clientIfSynchProtActivePort The operational state for the protection group.
none - no side is active.
A - the A port is active.
B - the B port is active. | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.91 |
| clientIfSynchProtPortStatus The operational synch protection state
for this port in the synch protection group.
down - this port is out of service.
up - this port is active. | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.92 |
| clientIfSynchProtToggleActivePort Command to toggle which port is active in the synch
prot group | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.27.2.2.1.1.93 |
| clientIfNearEndLoopbackTimeout Timeout for near end loopback (a.k.a. facility
loopback) to make sure connection to node is not
lost if ppp link is broken.
The unit is hours. 0.1 means 6 minutes. | column | Integer32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.94 |
| clientIfNearEndLoopbackEnabled Near end loopback (a.k.a. facility loopback)
is enabled. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.95 |
| clientIfChangeNearEndLoopbackCommand Command to change near end loopback (a.k.a.
facility loopback) and loopbacktimeout | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.27.2.2.1.1.96 |
| clientIfFarEndLoopbackEnabled Far end loopback (a.k.a. terminal loopback)
is enabled. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.97 |
| clientIfFarEndLoopbackTimeout Timeout for far end loopback (a.k.a. terminal
loopback) to make sure connection to node is
not lost if ppp link is broken.
The unit is hours. 0.1 means 6 minutes. | column | Integer32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.98 |
| clientIfChangeFarEndLoopbackCommand Command to change far end loopback (a.k.a.
terminal loopback) and loopbacktimeout | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.27.2.2.1.1.99 |