clientIfActualOpticalLayerMapping

LUM-CLIENT-MIB · .1.3.6.1.4.1.8708.2.27.2.2.1.1.134
MIB view Table view

Object

column LUM-TCOpticalLayerMappingType 
The actual optical layer mapping.

Context

MIB
LUM-CLIENT-MIB
OID
.1.3.6.1.4.1.8708.2.27.2.2.1.1.134
Type
column
Access
readonly
Status
current
Parent
clientIfEntry
Table
clientIfTable
Siblings
154

Syntax

LUM-TCOpticalLayerMappingType
Source
LUM-TCOpticalLayerMappingType
Base type
Enumeration

Values & Constraints

Type Values
0undefined
1fourOpticalLanes
2tenOpticalLanes
3singleOpticalChannel

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
clientIfIndex
An arbitrary index assigned to each entry.
columnUnsigned32.1.3.6.1.4.1.8708.2.27.2.2.1.1.1
clientIfAdminStatus
The administrative state for the interface. down - The interface is de-activated. service - The interface is activated but alarms are suppressed. Int…
columnLUM-TCBoardOrInterfaceAdminStatus.1.3.6.1.4.1.8708.2.27.2.2.1.1.10
clientIfFormatNotSupportedByHw
The HW revision does not support the selected signal format.
columnLUM-TCFaultStatus.1.3.6.1.4.1.8708.2.27.2.2.1.1.100
clientIfLaserMode
The administrative state of the TX-side laser. This is only used when signal format is ddgbeLine. on - The laser is turned on. als - Automatic Laser …
columnEnumeration.1.3.6.1.4.1.8708.2.27.2.2.1.1.101
clientIfAlarmIndicationSignalLineC2W
Alarm indication signal Line (AIS-L) on the client side. Applicable for Sonet signal formats. A: An 'all ones' Sonet signal is detected. D: Sonet sig…
columnLUM-TCFaultStatus.1.3.6.1.4.1.8708.2.27.2.2.1.1.102
clientIfFarEndClientFailure
Failure on far end client.
columnLUM-TCFaultStatus.1.3.6.1.4.1.8708.2.27.2.2.1.1.103
clientIfOHTransparency
The 'OH Transparency' setting shall be set to 'off' for standard SDH/SONET mode. Does not work when client wrapper is enabled. When set to 'on', the following tribu…
columnEnumeration.1.3.6.1.4.1.8708.2.27.2.2.1.1.104
clientIfConnectedLine
The line ports that this client port is connected to.
columnUnsigned32.1.3.6.1.4.1.8708.2.27.2.2.1.1.105
clientIfForwardingErrorCorrectionMode
The administrative state of the forwarding error correction function. disabled - FEC is disabled. enabled - FEC is activated. auto - a…
columnEnumeration.1.3.6.1.4.1.8708.2.27.2.2.1.1.106
clientIfNoFrequencySet
The tunable laser frequency has not been set. A: Tunable laser frequency is not set. D: Tunable laser frequency is set.
columnLUM-TCFaultStatus.1.3.6.1.4.1.8708.2.27.2.2.1.1.107
clientIfJitterAttenuatorBW
Determines the wander/jitter transfer bandwidth of the wander/jitter attenuator. With Option 1, the bandwidth is within 1 - 10 Hz, and with Option 2, the bandwidth is below 0.1 Hz…
columnEnumeration.1.3.6.1.4.1.8708.2.27.2.2.1.1.108
clientIfConnectionStatus
Shows the name of the wdm port and possible subchannel/vc4 that it is connected to or Unconnected if not connected.
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.8708.2.27.2.2.1.1.109
clientIfOperStatus
The operational state for the interface. notPresent - The physical resources are not available. down - The interface is de-activated or there are fau…
columnLUM-TCBoardOrInterfaceOperStatus.1.3.6.1.4.1.8708.2.27.2.2.1.1.11
clientIfLoopFilterUnlocked
The loopfilter is unlocked. This is applicable for synchronous formats. A: Loopfilter is unlocked D: Loopfilter is locked
columnLUM-TCFaultStatus.1.3.6.1.4.1.8708.2.27.2.2.1.1.110
clientIfCableLength
The 'Cable length' is applicable for SONET mode (T1). The settings are for short haul (intra-building) T1 networks and will adjust the power of the transmitted s…
columnEnumeration.1.3.6.1.4.1.8708.2.27.2.2.1.1.111
clientIfConnectedForeignIndex
Shows the index of the connected interface. Or 0 if unconnected.
columnUnsigned32.1.3.6.1.4.1.8708.2.27.2.2.1.1.112
clientIfDisconnect
Disconnect existing crossConnections
columnLUM-TCCommandString.1.3.6.1.4.1.8708.2.27.2.2.1.1.113
clientIfOHTransparencyBitMask
The OH transparency bitmask. Bits: K1K2 = 0x01 E1E2 = 0x02 F1 = 0x04 D1-D3 = 0x08 D4-D12 = 0x10 B1 = 0x20 B2 = 0x40 E1 = 0x80 E2 = 0x100 J0 = 0x200
columnUnsigned32.1.3.6.1.4.1.8708.2.27.2.2.1.1.114
clientIfOHTransparencyString
OH transparency bytes tells if J0, rest of RSOH/Section OH and/or MSOH/Line OH are transparent or not. When RSOH/Section OH is set to transparent the bytes E1, F1, D1-D3 and B1 is…
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.8708.2.27.2.2.1.1.115
clientIfOHTransparencySet
Set which bytes that should be OH transparent
columnLUM-TCCommandString.1.3.6.1.4.1.8708.2.27.2.2.1.1.116
clientIfAuAlarmIndicationSignalC2W
Alarm indication signal (AIS) on the client-side. Applicable for SDH/Sonet signal formats. A: An 'all ones' SDH signal is detected. D: SDH signal rec…
columnLUM-TCFaultStatus.1.3.6.1.4.1.8708.2.27.2.2.1.1.117
clientIfAuLossOfPointerC2W
Loss of pointer detected on the client-side. Applicable for SDH/Sonet signal formats. A: A loss of pointer is detected. D: SDH signal recovered.
columnLUM-TCFaultStatus.1.3.6.1.4.1.8708.2.27.2.2.1.1.118
clientIfAuLossOfPointerW2C
Loss of pointer detected on the line-side. Applicable for SDH/Sonet signal formats. A: A loss of pointer is detected. D: SDH signal recovered.
columnLUM-TCFaultStatus.1.3.6.1.4.1.8708.2.27.2.2.1.1.119
clientIfLaserStatus
The operational state of the laser. off - The laser is turned off. on - The laser is turned on.
columnEnumeration.1.3.6.1.4.1.8708.2.27.2.2.1.1.12
clientIfEthStandbyIndicator
Shows if this port is in standby state. Used with hub protection.
columnEnumeration.1.3.6.1.4.1.8708.2.27.2.2.1.1.120
clientIfAuAlarmIndicationSignalW2CSonet
Alarm indication signal (AIS-P) on the line-side. A: An 'all ones' Sonet signal is detected. D: Sonet signal recovered.
columnLUM-TCFaultStatus.1.3.6.1.4.1.8708.2.27.2.2.1.1.121
clientIfAuAlarmIndicationSignalC2WSonet
Alarm indication signal (AIS-P) on the client-side. A: An 'all ones' Sonet signal is detected. D: Sonet signal recovered.
columnLUM-TCFaultStatus.1.3.6.1.4.1.8708.2.27.2.2.1.1.122
clientIfAuLossOfPointerC2WSonet
Loss of pointer detected on the client-side. A: A loss of pointer is detected. D: Sonet signal recovered.
columnLUM-TCFaultStatus.1.3.6.1.4.1.8708.2.27.2.2.1.1.123
clientIfAuLossOfPointerW2CSonet
Loss of pointer detected on the line-side. A: A loss of pointer is detected. D: Sonet signal recovered.
columnLUM-TCFaultStatus.1.3.6.1.4.1.8708.2.27.2.2.1.1.124
clientIfTransceiverNoLoopback
The inserted transceiver does not support the given loopback command.
columnLUM-TCFaultStatus.1.3.6.1.4.1.8708.2.27.2.2.1.1.125
clientIfFecFailure
Too many errors to get valid FEC statistics. It is not possible to run control loops based on FEC statistics. A: Too many errors to get valid FEC statistics. …
columnLUM-TCFaultStatus.1.3.6.1.4.1.8708.2.27.2.2.1.1.126
clientIfLaneAlignmentError
Indicates whether multi-lane BASE-R PCS (Physical Coding Sublayer) has locked and aligned all received lanes. A: PCS receive lanes not locked and aligned. …
columnLUM-TCFaultStatus.1.3.6.1.4.1.8708.2.27.2.2.1.1.127
clientIfFecCorrectedZeros
The number of corrected zeros.
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.8708.2.27.2.2.1.1.128
clientIfFecCorrectedOnes
The number of corrected ones.
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.8708.2.27.2.2.1.1.129
clientIfTxSignalStatus
The operational state for outgoing (TX) signal of the interface. down - A fault that would lead to a protection switch has occurred. degraded - The s…
columnLUM-TCSignalStatusWithNA.1.3.6.1.4.1.8708.2.27.2.2.1.1.13
clientIfSignalDegraded
Too many error corrected. If more errors are corrected it might effect the client signal in a negative way.
columnLUM-TCFaultStatus.1.3.6.1.4.1.8708.2.27.2.2.1.1.130
clientIfFecType
Set FEC scheme. disabled -- none specific FEC scheme is enabled. gFec -- GFEC RS(255,239) FEC scheme, according to ITU.T G.975 superFecI4 -- Super FEC I.4 FE…
columnEnumeration.1.3.6.1.4.1.8708.2.27.2.2.1.1.131
clientIfSignalDegradeThreshold
The alarm Signal Degraded shall be signalled when BER reaches a limit. The value will be affecting all ports. Predefined BER levels rxBerLevel1 = 1E-12 rxBerLevel2 …
columnLUM-TCBerLevelMTOSI.1.3.6.1.4.1.8708.2.27.2.2.1.1.132
clientIfExpectedOpticalLayerMapping
The expected optical layer mapping.
columnLUM-TCOpticalLayerMappingType.1.3.6.1.4.1.8708.2.27.2.2.1.1.133
clientIfConfigurationMismatch
The inserted transceiver does not support the configuration of the optical layer mapping. A: A transceiver with other supported optical layer mapping than the re…
columnLUM-TCFaultStatus.1.3.6.1.4.1.8708.2.27.2.2.1.1.135
clientIfChromaticDispersion
Received chromatic dispersion that describe the spreading of a light pulse as it travels down a fiber when light pulses launched close together.
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.8708.2.27.2.2.1.1.136
clientIfDifferentialGroupDelay
The arrival time difference between two polarization states at the output of the media (fiber).
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.8708.2.27.2.2.1.1.137
clientIfTxState
The operational state of the transiver for outgoing (TX) signal. - Init started - Init ready - Data path locked - Laser ready off - Laser ready - Laser bias ready - Ready
columnLUM-TCTrxTxState.1.3.6.1.4.1.8708.2.27.2.2.1.1.138
clientIfRxState
The operational state of the transiver for outgoing (RX) signal. - Init started - Init ready - Frequency ready - Input signal received - A/D Converter ready - Dispersion compensat…
columnLUM-TCTrxRxState.1.3.6.1.4.1.8708.2.27.2.2.1.1.139
clientIfForwardAls
Forward Automatic Laser Shut-down. Decides if laser shutdown of the client should occur when a defect on the line or remote client is detected. disabled - The laser…
columnEnumeration.1.3.6.1.4.1.8708.2.27.2.2.1.1.14
clientIfIdx
Internal object reference
columnInteger32.1.3.6.1.4.1.8708.2.27.2.2.1.1.140
clientIfIfNo
The physical interface number of the actual multi-connector port.
columnLUM-TCPortNumber.1.3.6.1.4.1.8708.2.27.2.2.1.1.141
clientIfIdxIf
Internal object reference of the actual multi-connector port.
columnInteger32.1.3.6.1.4.1.8708.2.27.2.2.1.1.142
clientIfUpPortId
Internal port reference for traffic unit.
columnInteger32.1.3.6.1.4.1.8708.2.27.2.2.1.1.143
clientIfNoOfLanes
Number of lanes on port
columnInteger32.1.3.6.1.4.1.8708.2.27.2.2.1.1.144
clientIfFecCorrectedBits
FEC counter. Number of corrected bits
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.8708.2.27.2.2.1.1.145
clientIfOSNRMargin
Optical signal-to-noise ratio margin (dB/0.1nm), based on calculation from rate of corrected bits.
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.8708.2.27.2.2.1.1.146
clientIfExpectedPhysicalLayerMapping
The expected physical layer mapping.
columnLUM-TCPhysicalLayerMappingType.1.3.6.1.4.1.8708.2.27.2.2.1.1.147
clientIfSignalDirection
Indicates the direction of the signal. rx - Inbound direction tx - Outbound direction biDir - Bidirectional txRx …
columnLUM-TCSignalDirection.1.3.6.1.4.1.8708.2.27.2.2.1.1.148
clientIfAid
The access identifier (AID) of the interface. The format is according to GR-833.
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.8708.2.27.2.2.1.1.149
clientIfSuppressRemoteAlarms
Suppress AIS in the alarm list. The fault status on the port object can, however, be seen. disabled - alarms are not suppressed. enabled - alarms are…
columnEnumeration.1.3.6.1.4.1.8708.2.27.2.2.1.1.15
clientIfPhysicalLocation
The physical location of the if. The format is according to GR-833.
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.8708.2.27.2.2.1.1.150
clientIfTrxCommunicationFailure
The board is unable to communicate with the transceiver. alarm: Protocol errors detected on the transceiver control link. ok: No communication errors…
columnLUM-TCFaultStatus.1.3.6.1.4.1.8708.2.27.2.2.1.1.151
clientIfTribPortId
Tributary port id.
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.8708.2.27.2.2.1.1.152
clientIfIfType
Type of interface (Individual or bundled).
columnLUM-TCInterfaceType.1.3.6.1.4.1.8708.2.27.2.2.1.1.153
clientIfConfigurationCommandSNMP
Command to change the signal format, and, if applicable, also the mode (framed, transparent) via SNMP.
columnLUM-TCCommandString.1.3.6.1.4.1.8708.2.27.2.2.1.1.154
clientIfTrxPowerOutOfRange
The power classification of the transceiver exceeds the design limit of the board. alarm: A transceiver with a power classification that exceeds the design l…
columnLUM-TCFaultStatus.1.3.6.1.4.1.8708.2.27.2.2.1.1.155
clientIfFarEndLoopback
Loop the client TX signal back to the client RX. This is also called Terminal loopback. disabled - the signal is not looped enabled - the signal is l…
columnEnumeration.1.3.6.1.4.1.8708.2.27.2.2.1.1.16
clientIfFormat
The expected signal format. The default value is board dependent. For information about the default value for this particular board, please refer to the user manual.
columnLUM-TCSignalFormat.1.3.6.1.4.1.8708.2.27.2.2.1.1.17
clientIfGfpMode
Generic framing procedure mode
columnEnumeration.1.3.6.1.4.1.8708.2.27.2.2.1.1.18
clientIfBandWidth
Band-width in VC-3 or VC-4. The parameter is interpreted as VC-3 or VC-4 depending on the traffic combination: - VC-3 is used in framedGbEx10 - VC-4 …
columnInteger32.1.3.6.1.4.1.8708.2.27.2.2.1.1.19
clientIfName
The management name of the interface, for example 'client:1:2:1', where the first number indicates sub-rack, the second slot number and the third is the port number. Examples: …
columnLUM-TCMgmtNameString.1.3.6.1.4.1.8708.2.27.2.2.1.1.2
clientIfRateLimit
Rate limit of link in 1,000,000 bits (Mb) per second. Zero (0) is a special value meaning that the rate-limiting procedure is disabled. The legal ran…
columnInteger32.1.3.6.1.4.1.8708.2.27.2.2.1.1.20
clientIfAutoNegotiationMode
The wanted auto negotiation mode. off - auto negotiation process is disabled on - auto negotiation process is enabled
columnEnumeration.1.3.6.1.4.1.8708.2.27.2.2.1.1.21
clientIfAutoNegotiationStatus
The result of the auto negotiation procedure incomplete - the result is still pending half - half duplex full - full duplex
columnEnumeration.1.3.6.1.4.1.8708.2.27.2.2.1.1.22
clientIfDuplexCapability
The duplex capability of the HW. half - supports half duplex full - supports full duplex
columnEnumeration.1.3.6.1.4.1.8708.2.27.2.2.1.1.23
clientIfFlowControlMode
The mode for handling flow control between the local device and link partner. The PAUSE settings has the following meaning when auto-negotiation is enabled. …
columnEnumeration.1.3.6.1.4.1.8708.2.27.2.2.1.1.24
clientIfInterPacketGap
Time between the frames in nano seconds. Legal values are 64, 72, 80, ... 200, 320, 328, 336, ... 456
columnUnsigned32.1.3.6.1.4.1.8708.2.27.2.2.1.1.25
clientIfFrameSize
The maximum size of the transmitted and received frames (in bytes).
columnUnsigned32.1.3.6.1.4.1.8708.2.27.2.2.1.1.26
clientIfTrxClass
String that describes the transceiver class.
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.8708.2.27.2.2.1.1.27
clientIfLaserBias
Measures laser bias current value in tenths of mA (0.1 mA).
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.8708.2.27.2.2.1.1.28
clientIfPowerLevel
The received power level in units of 0.1 dBm.
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.8708.2.27.2.2.1.1.29
clientIfDescr
User configurable label. This attribute can be written via SNMP.
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.8708.2.27.2.2.1.1.3
clientIfReceiverSensitivity
The lowest power that the receiver is guaranteed to handle, in units of 0.1 dBm.
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.8708.2.27.2.2.1.1.30
clientIfPowerLevelLowRelativeThreshold
The lower threshold for received power level in units of 0.1 dB, relative to the receiver sensitivity.
columnInteger32.1.3.6.1.4.1.8708.2.27.2.2.1.1.31
clientIfLossOfSignal
Loss of signal. Applicable for all signal formats. A(ctivation): Active loss of signal HW indication. D(e-activation): Inactive loss of signal HW ind…
columnLUM-TCFaultStatus.1.3.6.1.4.1.8708.2.27.2.2.1.1.32
clientIfLossOfFrame
Loss of frame. All forms of sync loss.
columnLUM-TCFaultStatus.1.3.6.1.4.1.8708.2.27.2.2.1.1.33
clientIfBitrateMismatch
Bitrate mismatch (Other). Applicable for other signal formats. D: The interface is unable to lock to the inserted signal. D: The interface is able to…
columnLUM-TCFaultStatus.1.3.6.1.4.1.8708.2.27.2.2.1.1.34
clientIfAuAlarmIndicationSignalW2C
Alarm indication signal (AIS) on the trunk-side. Applicable for SDH/Sonet signal formats. A: An 'all ones' SDH signal is detected. D: SDH signal reco…
columnLUM-TCFaultStatus.1.3.6.1.4.1.8708.2.27.2.2.1.1.35
clientIfTransmitterFailed
The transceiver HW has detected a failure in the transmitter part. A: The transmitter has failed D: The transmitter is OK again
columnLUM-TCFaultStatus.1.3.6.1.4.1.8708.2.27.2.2.1.1.36
clientIfTrxCodeMismatch
The inserted transceiver does not have a legal manufacturer code. A: A transceiver with illegal code is inserted. D: The transceiver with illegal cod…
columnLUM-TCFaultStatus.1.3.6.1.4.1.8708.2.27.2.2.1.1.37
clientIfTrxBitrateUnavailable
The inserted transceiver does not support the requested bit rate. A: A transceiver with other supported bit rate than the requested bit rate is inserted. …
columnLUM-TCFaultStatus.1.3.6.1.4.1.8708.2.27.2.2.1.1.38
clientIfTrxMissing
An expected transceiver is missing. A: An expected transceiver is missing. D: The missing transceiver is inserted.
columnLUM-TCFaultStatus.1.3.6.1.4.1.8708.2.27.2.2.1.1.39
clientIfSubrack
The number of the subrack where the interface is located.
columnLUM-TCSubrackNumber.1.3.6.1.4.1.8708.2.27.2.2.1.1.4
clientIfReceivedPowerHigh
Received power level is too high. Applicable for all signal formats. A: The received power level exceeds the the built-in overload threshold. D: The …
columnLUM-TCFaultStatus.1.3.6.1.4.1.8708.2.27.2.2.1.1.40
clientIfReceivedPowerLow
Received power level low threshold exceeded. Applicable for all signal formats. A: The received power level is below the associated threshold. D: The…
columnLUM-TCFaultStatus.1.3.6.1.4.1.8708.2.27.2.2.1.1.41
clientIfLinkDown
A: Failure to negotiate a connection with the other party. D: A connection is negotiated.
columnLUM-TCFaultStatus.1.3.6.1.4.1.8708.2.27.2.2.1.1.42
clientIfConfigurationCommand
Command to change the signal format, and, if applicable, also the mode (framed, transparent).
columnLUM-TCCommandString.1.3.6.1.4.1.8708.2.27.2.2.1.1.43
clientIfGbeUtilization
Shows the current bandwidth utilization measured at the physical (802.3 PHY) layer. The value represents a snapshot of the utilization during the latest second. It is expressed i…
columnUnsigned32.1.3.6.1.4.1.8708.2.27.2.2.1.1.44
clientIfLossOfSync
Loss of sync. All forms of sync loss. A: GbE 'frame' can not be located. D: GbE 'frame' is located.
columnLUM-TCFaultStatus.1.3.6.1.4.1.8708.2.27.2.2.1.1.45
clientIfConfigureTrxModeCommand
Command to change the TRX mode (client or line) and/or TRX media (optical or electrical).
columnLUM-TCCommandString.1.3.6.1.4.1.8708.2.27.2.2.1.1.46
clientIfTrxMode
Shows if the port is configured as: - normal CLIENT interface connected to a non XTM Series client equipment, with non-colored, or colored TRXes. -…
columnEnumeration.1.3.6.1.4.1.8708.2.27.2.2.1.1.47
clientIfExpectedTxFrequency
The expected frequency given in hundreds of GHz (0.01 GHz).
columnLUM-TCLambdaFrequency.1.3.6.1.4.1.8708.2.27.2.2.1.1.48
clientIfTxFrequency
The transmitted frequency given in hundreds of GHz (0.01 GHz).
columnLUM-TCLambdaFrequency.1.3.6.1.4.1.8708.2.27.2.2.1.1.49
clientIfSlot
The number of the slot where the interface is located.
columnLUM-TCSlotNumber.1.3.6.1.4.1.8708.2.27.2.2.1.1.5
clientIfUnexpectedTxFrequency
The actual frequency does not match the pre-configured frequency. A pre-configured frequency of '0' matches all actual frequencies. A: The configured…
columnLUM-TCFaultStatus.1.3.6.1.4.1.8708.2.27.2.2.1.1.50
clientIfIllegalFrequency
The frequency supported by the transceiver is not recognized by the system. A: Invalid or unknown frequency information is detected in the (pluggable) transceive…
columnLUM-TCFaultStatus.1.3.6.1.4.1.8708.2.27.2.2.1.1.51
clientIfLaserForcedOn
When enabled, the laser is on regardless of whether there is a trunc signal present or not. disabled - the laser is only on when there is a trunc signal.…
columnEnumeration.1.3.6.1.4.1.8708.2.27.2.2.1.1.52
clientIfTrxMedia
Defines the media and capability of the TRX.
columnLUM-TCTrxMedia.1.3.6.1.4.1.8708.2.27.2.2.1.1.53
clientIfTrxMediaMismatch
The TRX media does not match the expected one. A: Invalid or mismatching trx media is detected. D: The (pluggable) transceiver or board is repl…
columnLUM-TCFaultStatus.1.3.6.1.4.1.8708.2.27.2.2.1.1.54
clientIfTruncAutoNegotiationMode
Decides whether auto negotiation shall be performed over the trunc connection. This is applicable when the terminating node at the other side of the trunc is config…
columnEnumeration.1.3.6.1.4.1.8708.2.27.2.2.1.1.55
clientIfObjectProperty
Property mask.
columnLUM-TCObjectProperty.1.3.6.1.4.1.8708.2.27.2.2.1.1.56
clientIfTxPowerLevel
The transmitted power level in units of 0.1 dBm.
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.8708.2.27.2.2.1.1.57
clientIfLaserTempActual
The actual laser temperature in units of 0.1 degrees centigrade.
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.8708.2.27.2.2.1.1.58
clientIfTraceIntrusionMode
Indicates whether the trace identifier should be inserted into the transmitted signal or to be transparent. disabled - The trace identifier is taken from the recevi…
columnEnumeration.1.3.6.1.4.1.8708.2.27.2.2.1.1.59
clientIfTxPort
The number of the port where the TX-side of the interface is located.
columnLUM-TCPortNumber.1.3.6.1.4.1.8708.2.27.2.2.1.1.6
clientIfTraceTransmitted
The trace identifier to be transmitted from this interface. The identifier length is by default 0 to 15. For mxp8iiSonet board the length i 0 to 62. …
columnOctetString.1.3.6.1.4.1.8708.2.27.2.2.1.1.60
clientIfTraceReceived
The received trace identifier for this interface.
columnOctetString.1.3.6.1.4.1.8708.2.27.2.2.1.1.61
clientIfTraceExpected
Trace identifier used for matching against the received trace identifier. The identifier length is by default 0 to 15. For mxp8iiSonet board the length is 0 to 62.
columnOctetString.1.3.6.1.4.1.8708.2.27.2.2.1.1.62
clientIfTraceAlarmMode
Controls if the trace identifier mismatch alarm should be raised. disabled - The alarm is disabled. enabled - The alarm is raised if expected trace i…
columnEnumeration.1.3.6.1.4.1.8708.2.27.2.2.1.1.63
clientIfTraceMismatch
Indicates if the expected trace identifier differs from the received trace identifier. A: The received trace identifier differs from the expected trace identifier. …
columnLUM-TCFaultStatus.1.3.6.1.4.1.8708.2.27.2.2.1.1.64
clientIfNearEndLoopback
Loop the client RX signal back to the client TX. This is also called Facility loopback disabled - the signal is not looped enabled - the signal is lo…
columnEnumeration.1.3.6.1.4.1.8708.2.27.2.2.1.1.65
clientIfRxSignalStatus
The operational state for incoming (RX) signal of the interface. down - A major fault has occurred degraded - The signal quality is impaired. …
columnLUM-TCSignalStatusWithNA.1.3.6.1.4.1.8708.2.27.2.2.1.1.66
clientIfMsAlarmIndicationSignalC2W
MS Alarm indication signal (MS-AIS) on the client side. Applicable for SDH/Sonet signal formats. A: An 'all ones' pattern is detected. D: The signal …
columnLUM-TCFaultStatus.1.3.6.1.4.1.8708.2.27.2.2.1.1.67
clientIfMsAlarmIndicationSignalW2C
MS Alarm indication signal (MS-AIS) on the trunc side. Applicable for SDH/Sonet/IWDM signal formats. A: An 'all ones' pattern is detected. D: The sig…
columnLUM-TCFaultStatus.1.3.6.1.4.1.8708.2.27.2.2.1.1.68
clientIfRemoteDefectIndication
Remote defect indication. Applicable for SDH/Sonet signal formats. A: RDI indication (in SDH/Sonet frame) active. D: RDI indication inactive.
columnLUM-TCFaultStatus.1.3.6.1.4.1.8708.2.27.2.2.1.1.69
clientIfRxPort
The number of the port where the RX-side of the interface is located.
columnLUM-TCPortNumber.1.3.6.1.4.1.8708.2.27.2.2.1.1.7
clientIfJ1TxTrailTrace
The J1 trail trace identifier(s) to be transmitted for the VC4s/VC3s related to this interface, in the line signal (STM16/OC48). This parameter can be used in two d…
columnOctetString.1.3.6.1.4.1.8708.2.27.2.2.1.1.70
clientIfJ1TxTrailTraceInsertionMode
Controls how the J1 trail trace insertion should work, i.e. how the j1TxTrailTrace parameter shall be inserted in the line signal. Important: there is only one j1Tx…
columnEnumeration.1.3.6.1.4.1.8708.2.27.2.2.1.1.71
clientIfTrxFailed
A transceiver hardware failure is detected. A: The transceiver fails. D: The transceiver is replaced.
columnLUM-TCFaultStatus.1.3.6.1.4.1.8708.2.27.2.2.1.1.72
clientIfDisabled
The interface is disabled. A: Interface disabled. D: Interface enabled.
columnLUM-TCFaultStatus.1.3.6.1.4.1.8708.2.27.2.2.1.1.73
clientIfLoopback
The interface is set in loopback mode. A: Loopback enabled. D: Loopback disabled.
columnLUM-TCFaultStatus.1.3.6.1.4.1.8708.2.27.2.2.1.1.74
clientIfVcGroupFailedW2C
The received line signal contains a VC mapped to this interface, that is faulty, e.g. unequipped. Please note that this fault is in the LINE SIGNAL, but is presente…
columnLUM-TCFaultStatus.1.3.6.1.4.1.8708.2.27.2.2.1.1.75
clientIfReadJ1
Read the received J1 for the VC4/VC3 in the STM16 frame associated to this interface. Synopsis: readJ1
columnLUM-TCCommandString.1.3.6.1.4.1.8708.2.27.2.2.1.1.76
clientIfClientSignalFailed
The received line signal contains a VC mapped to this interface, that is faulty, e.g. unequipped. Please note that this fault is in the LINE SIGNAL, but is presente…
columnLUM-TCFaultStatus.1.3.6.1.4.1.8708.2.27.2.2.1.1.77
clientIfAuLossOfPointer
Loss of pointer.
columnLUM-TCFaultStatus.1.3.6.1.4.1.8708.2.27.2.2.1.1.78
clientIfGfpLossOfFrame
GFP Loss of frame.
columnLUM-TCFaultStatus.1.3.6.1.4.1.8708.2.27.2.2.1.1.79
clientIfInvPhysIndexOrZero
The row in the invPhysTable for this interface. Set to 0 if not known.
columnUnsigned32.1.3.6.1.4.1.8708.2.27.2.2.1.1.8
clientIfHighSpeed
The expected signal bit rate in units of 1,000,000 bits (Mb) per second. If this object reports a value of 'n' then the speed of the interface is somewhere in the range of 'n-500,…
columnUnsigned32.1.3.6.1.4.1.8708.2.27.2.2.1.1.80
clientIfActualFormat
The actual signal format.
columnLUM-TCSignalFormat.1.3.6.1.4.1.8708.2.27.2.2.1.1.81
clientIfRdiIntrusionMode
Indicates whether RDI information should be inserted in the transmitted signal. disabled - No RDI information is inserted in the transmitted signal. …
columnEnumeration.1.3.6.1.4.1.8708.2.27.2.2.1.1.82
clientIfMuxQuadVc4
States which quadrant of the payload that the interface is connected to in rx direction. (outgoing line)
columnUnsigned32.1.3.6.1.4.1.8708.2.27.2.2.1.1.83
clientIfDemuxQuadVc4
States whitch quadrant of the payload that the interface is connected to in tx direction. (outgoing client)
columnUnsigned32.1.3.6.1.4.1.8708.2.27.2.2.1.1.84
clientIfCcConnectionMode
controls if DemuxPayloadQuad is same as MuxPayloadQuad (same => connected, not same => disconnected)
columnEnumeration.1.3.6.1.4.1.8708.2.27.2.2.1.1.85
clientIfCcConfigurationCommand
Command to change the crossconnect, If no arguments are given, the user will be prompted.
columnLUM-TCCommandString.1.3.6.1.4.1.8708.2.27.2.2.1.1.86
clientIfIllegalSignalFormat
IllegalSignalFormat. A(ctivation): Actual Format does NOT match expected Format. D(e-activation): Actual Format does match expected Format.
columnLUM-TCFaultStatus.1.3.6.1.4.1.8708.2.27.2.2.1.1.87
clientIfSynchProtPortId
The Id for this port in the synch prot group, to identify the port. (A or B)
columnEnumeration.1.3.6.1.4.1.8708.2.27.2.2.1.1.88
clientIfSynchProtGroupMemberPort
The port number for the TX side of the port that is in this synch protection group.
columnLUM-TCPortNumber.1.3.6.1.4.1.8708.2.27.2.2.1.1.89
clientIfEntityId
Index in entity table. -- Only used for notifications
columnUnsigned32.1.3.6.1.4.1.8708.2.27.2.2.1.1.9
clientIfSynchProtGroupStatus
Note: This object is deprecated. The operational state for the protection group. bothDown - both sides down bothUp - both sides up …
columnEnumeration.1.3.6.1.4.1.8708.2.27.2.2.1.1.90
clientIfSynchProtActivePort
The operational state for the protection group. none - no side is active. A - the A port is active. B - the B port is active.
columnEnumeration.1.3.6.1.4.1.8708.2.27.2.2.1.1.91
clientIfSynchProtPortStatus
The operational synch protection state for this port in the synch protection group. down - this port is out of service. up - this port is active.
columnEnumeration.1.3.6.1.4.1.8708.2.27.2.2.1.1.92
clientIfSynchProtToggleActivePort
Command to toggle which port is active in the synch prot group
columnLUM-TCCommandString.1.3.6.1.4.1.8708.2.27.2.2.1.1.93
clientIfNearEndLoopbackTimeout
Timeout for near end loopback (a.k.a. facility loopback) to make sure connection to node is not lost if ppp link is broken. The unit is hours. 0.1 means 6 minutes.
columnInteger32.1.3.6.1.4.1.8708.2.27.2.2.1.1.94
clientIfNearEndLoopbackEnabled
Near end loopback (a.k.a. facility loopback) is enabled.
columnLUM-TCFaultStatus.1.3.6.1.4.1.8708.2.27.2.2.1.1.95
clientIfChangeNearEndLoopbackCommand
Command to change near end loopback (a.k.a. facility loopback) and loopbacktimeout
columnLUM-TCCommandString.1.3.6.1.4.1.8708.2.27.2.2.1.1.96
clientIfFarEndLoopbackEnabled
Far end loopback (a.k.a. terminal loopback) is enabled.
columnLUM-TCFaultStatus.1.3.6.1.4.1.8708.2.27.2.2.1.1.97
clientIfFarEndLoopbackTimeout
Timeout for far end loopback (a.k.a. terminal loopback) to make sure connection to node is not lost if ppp link is broken. The unit is hours. 0.1 means 6 minutes.
columnInteger32.1.3.6.1.4.1.8708.2.27.2.2.1.1.98
clientIfChangeFarEndLoopbackCommand
Command to change far end loopback (a.k.a. terminal loopback) and loopbacktimeout
columnLUM-TCCommandString.1.3.6.1.4.1.8708.2.27.2.2.1.1.99