clientIfCableLength
LUM-CLIENT-MIB ·
.1.3.6.1.4.1.8708.2.27.2.2.1.1.111
Object
column
r/w
Enumeration
The 'Cable length' is applicable for SONET mode
(T1).
The settings are for short haul (intra-building) T1
networks and will adjust the power of the
transmitted signal to compensate for the
attenuation of the cable. This is important when
connecting to older T1 equipment.
This setting can also be used to equalize the
signal at the far-end receiver to avoid cross-talk
with other signals.
The values below are for an obsolete ABAM 600 cable
(Western Electric), but a modern CAT5e cable will
have similar performance.
LINE BUILD-OUT
Attenuation values are measured at 0.772 MHz
0 - 133 ft, 0 - 40.5 m, 0.6 dB
133 - 266 ft, 40.5 - 81.1 m, 1.2 dB
266 - 399 ft, 81.1 - 121.6 m, 1.8 dB
399 - 533 ft, 121.6 - 162.5 m, 2.4 dB
533 - 655 ft, 162.5 - 199.6 m, 3.0 dB
Context
- MIB
- LUM-CLIENT-MIB
- OID
.1.3.6.1.4.1.8708.2.27.2.2.1.1.111- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- clientIfEntry
- Table
- clientIfTable
- Siblings
- 154
Syntax
Enumeration
Values & Constraints
Enumerated Values
0 | feet133 |
1 | feet266 |
2 | feet399 |
3 | feet533 |
4 | feet655 |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| clientIfIndex An arbitrary index assigned to each entry. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.1 |
| clientIfAdminStatus The administrative state for the interface.
down - The interface is de-activated.
service - The interface is activated but alarms are
suppressed. Int… | column | LUM-TCBoardOrInterfaceAdminStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.10 |
| clientIfFormatNotSupportedByHw The HW revision does not support
the selected signal format. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.100 |
| clientIfLaserMode The administrative state of the TX-side laser.
This is only used when signal format is ddgbeLine.
on - The laser is turned on.
als - Automatic Laser … | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.101 |
| clientIfAlarmIndicationSignalLineC2W Alarm indication signal Line (AIS-L) on the
client side.
Applicable for Sonet signal formats.
A: An 'all ones' Sonet signal is detected.
D: Sonet sig… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.102 |
| clientIfFarEndClientFailure Failure on far end client. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.103 |
| clientIfOHTransparency The 'OH Transparency' setting shall be set to 'off'
for standard SDH/SONET mode. Does not work when
client wrapper is enabled.
When set to 'on', the following tribu… | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.104 |
| clientIfConnectedLine The line ports that this client port is connected to. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.105 |
| clientIfForwardingErrorCorrectionMode The administrative state of the forwarding error
correction function.
disabled - FEC is disabled.
enabled - FEC is activated.
auto - a… | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.106 |
| clientIfNoFrequencySet The tunable laser frequency has not been set.
A: Tunable laser frequency is not set.
D: Tunable laser frequency is set. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.107 |
| clientIfJitterAttenuatorBW Determines the wander/jitter transfer bandwidth
of the wander/jitter attenuator.
With Option 1, the bandwidth is within 1 - 10 Hz,
and with Option 2, the bandwidth is below 0.1 Hz… | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.108 |
| clientIfConnectionStatus Shows the name of the wdm port and
possible subchannel/vc4 that it is connected to
or Unconnected if not connected. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.27.2.2.1.1.109 |
| clientIfOperStatus The operational state for the interface.
notPresent - The physical resources are not
available.
down - The interface is de-activated or there are
fau… | column | LUM-TCBoardOrInterfaceOperStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.11 |
| clientIfLoopFilterUnlocked The loopfilter is unlocked.
This is applicable for synchronous formats.
A: Loopfilter is unlocked
D: Loopfilter is locked | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.110 |
| clientIfConnectedForeignIndex Shows the index of the connected interface.
Or 0 if unconnected. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.112 |
| clientIfDisconnect Disconnect existing crossConnections | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.27.2.2.1.1.113 |
| clientIfOHTransparencyBitMask The OH transparency bitmask.
Bits:
K1K2 = 0x01
E1E2 = 0x02
F1 = 0x04
D1-D3 = 0x08
D4-D12 = 0x10
B1 = 0x20
B2 = 0x40
E1 = 0x80
E2 = 0x100
J0 = 0x200 | column | Unsigned32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.114 |
| clientIfOHTransparencyString OH transparency bytes tells if J0, rest
of RSOH/Section OH and/or MSOH/Line OH are
transparent or not.
When RSOH/Section OH is set to transparent the bytes
E1, F1, D1-D3 and B1 is… | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.27.2.2.1.1.115 |
| clientIfOHTransparencySet Set which bytes that should be OH transparent | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.27.2.2.1.1.116 |
| clientIfAuAlarmIndicationSignalC2W Alarm indication signal (AIS) on the
client-side.
Applicable for SDH/Sonet signal formats.
A: An 'all ones' SDH signal is detected.
D: SDH signal rec… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.117 |
| clientIfAuLossOfPointerC2W Loss of pointer detected on the client-side.
Applicable for SDH/Sonet signal formats.
A: A loss of pointer is detected.
D: SDH signal recovered. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.118 |
| clientIfAuLossOfPointerW2C Loss of pointer detected on the line-side.
Applicable for SDH/Sonet signal formats.
A: A loss of pointer is detected.
D: SDH signal recovered. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.119 |
| clientIfLaserStatus The operational state of the laser.
off - The laser is turned off.
on - The laser is turned on. | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.12 |
| clientIfEthStandbyIndicator Shows if this port is in standby state.
Used with hub protection. | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.120 |
| clientIfAuAlarmIndicationSignalW2CSonet Alarm indication signal (AIS-P) on the line-side.
A: An 'all ones' Sonet signal is detected.
D: Sonet signal recovered. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.121 |
| clientIfAuAlarmIndicationSignalC2WSonet Alarm indication signal (AIS-P) on the
client-side.
A: An 'all ones' Sonet signal is detected.
D: Sonet signal recovered. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.122 |
| clientIfAuLossOfPointerC2WSonet Loss of pointer detected on the client-side.
A: A loss of pointer is detected.
D: Sonet signal recovered. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.123 |
| clientIfAuLossOfPointerW2CSonet Loss of pointer detected on the line-side.
A: A loss of pointer is detected.
D: Sonet signal recovered. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.124 |
| clientIfTransceiverNoLoopback The inserted transceiver does not support
the given loopback command. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.125 |
| clientIfFecFailure Too many errors to get valid FEC statistics. It is not
possible to run control loops based on FEC statistics.
A: Too many errors to get valid FEC statistics.
… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.126 |
| clientIfLaneAlignmentError Indicates whether multi-lane
BASE-R PCS (Physical Coding Sublayer)
has locked and aligned all received lanes.
A: PCS receive lanes not locked and aligned.
… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.127 |
| clientIfFecCorrectedZeros The number of corrected zeros. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.128 |
| clientIfFecCorrectedOnes The number of corrected ones. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.129 |
| clientIfTxSignalStatus The operational state for outgoing (TX) signal
of the interface.
down - A fault that would lead to a protection
switch has occurred.
degraded - The s… | column | LUM-TCSignalStatusWithNA | .1.3.6.1.4.1.8708.2.27.2.2.1.1.13 |
| clientIfSignalDegraded Too many error corrected.
If more errors are corrected
it might effect the client signal
in a negative way. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.130 |
| clientIfFecType Set FEC scheme.
disabled -- none specific FEC scheme is enabled.
gFec -- GFEC RS(255,239) FEC scheme,
according to ITU.T G.975
superFecI4 -- Super FEC I.4 FE… | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.131 |
| clientIfSignalDegradeThreshold The alarm Signal Degraded shall be signalled
when BER reaches a limit.
The value will be affecting all ports.
Predefined BER levels
rxBerLevel1 = 1E-12
rxBerLevel2 … | column | LUM-TCBerLevelMTOSI | .1.3.6.1.4.1.8708.2.27.2.2.1.1.132 |
| clientIfExpectedOpticalLayerMapping The expected optical layer mapping. | column | LUM-TCOpticalLayerMappingType | .1.3.6.1.4.1.8708.2.27.2.2.1.1.133 |
| clientIfActualOpticalLayerMapping The actual optical layer mapping. | column | LUM-TCOpticalLayerMappingType | .1.3.6.1.4.1.8708.2.27.2.2.1.1.134 |
| clientIfConfigurationMismatch The inserted transceiver does not support the
configuration of the optical layer mapping.
A: A transceiver with other supported optical layer
mapping than the re… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.135 |
| clientIfChromaticDispersion Received chromatic dispersion that describe the spreading of a light
pulse as it travels down a fiber when light pulses launched close together. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.136 |
| clientIfDifferentialGroupDelay The arrival time difference between two polarization states at
the output of the media (fiber). | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.137 |
| clientIfTxState The operational state of the transiver for outgoing (TX) signal.
- Init started
- Init ready
- Data path locked
- Laser ready off
- Laser ready
- Laser bias ready
- Ready | column | LUM-TCTrxTxState | .1.3.6.1.4.1.8708.2.27.2.2.1.1.138 |
| clientIfRxState The operational state of the transiver for outgoing (RX) signal.
- Init started
- Init ready
- Frequency ready
- Input signal received
- A/D Converter ready
- Dispersion compensat… | column | LUM-TCTrxRxState | .1.3.6.1.4.1.8708.2.27.2.2.1.1.139 |
| clientIfForwardAls Forward Automatic Laser Shut-down. Decides if
laser shutdown of the client should occur when
a defect on the line or remote client is detected.
disabled - The laser… | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.14 |
| clientIfIdx Internal object reference | column | Integer32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.140 |
| clientIfIfNo The physical interface number of the actual multi-connector port. | column | LUM-TCPortNumber | .1.3.6.1.4.1.8708.2.27.2.2.1.1.141 |
| clientIfIdxIf Internal object reference of the actual multi-connector port. | column | Integer32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.142 |
| clientIfUpPortId Internal port reference for traffic unit. | column | Integer32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.143 |
| clientIfNoOfLanes Number of lanes on port | column | Integer32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.144 |
| clientIfFecCorrectedBits FEC counter. Number of corrected bits | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.145 |
| clientIfOSNRMargin Optical signal-to-noise ratio margin (dB/0.1nm), based on calculation from rate of corrected bits. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.146 |
| clientIfExpectedPhysicalLayerMapping The expected physical layer mapping. | column | LUM-TCPhysicalLayerMappingType | .1.3.6.1.4.1.8708.2.27.2.2.1.1.147 |
| clientIfSignalDirection Indicates the direction of the signal.
rx - Inbound direction
tx - Outbound direction
biDir - Bidirectional
txRx … | column | LUM-TCSignalDirection | .1.3.6.1.4.1.8708.2.27.2.2.1.1.148 |
| clientIfAid The access identifier (AID) of the interface.
The format is according to GR-833. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.27.2.2.1.1.149 |
| clientIfSuppressRemoteAlarms Suppress AIS in the alarm list.
The fault status on the port object can, however,
be seen.
disabled - alarms are not suppressed.
enabled - alarms are… | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.15 |
| clientIfPhysicalLocation The physical location of the if.
The format is according to GR-833. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.27.2.2.1.1.150 |
| clientIfTrxCommunicationFailure The board is unable to communicate with the transceiver.
alarm: Protocol errors detected on the transceiver control link.
ok: No communication errors… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.151 |
| clientIfTribPortId Tributary port id. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.152 |
| clientIfIfType Type of interface (Individual or bundled). | column | LUM-TCInterfaceType | .1.3.6.1.4.1.8708.2.27.2.2.1.1.153 |
| clientIfConfigurationCommandSNMP Command to change the signal format, and, if
applicable, also the mode (framed, transparent) via SNMP. | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.27.2.2.1.1.154 |
| clientIfTrxPowerOutOfRange The power classification of the transceiver exceeds the design limit of the board.
alarm: A transceiver with a power classification that exceeds
the design l… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.155 |
| clientIfFarEndLoopback Loop the client TX signal back to the client RX.
This is also called Terminal loopback.
disabled - the signal is not looped
enabled - the signal is l… | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.16 |
| clientIfFormat The expected signal format.
The default value is board dependent. For information
about the default value for this particular board,
please refer to the user manual. | column | LUM-TCSignalFormat | .1.3.6.1.4.1.8708.2.27.2.2.1.1.17 |
| clientIfGfpMode Generic framing procedure mode | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.18 |
| clientIfBandWidth Band-width in VC-3 or VC-4.
The parameter is interpreted as VC-3 or VC-4
depending on the traffic combination:
- VC-3 is used in framedGbEx10
- VC-4 … | column | Integer32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.19 |
| clientIfName The management name of the interface, for
example 'client:1:2:1', where the first number
indicates sub-rack, the second slot number and
the third is the port number.
Examples:
… | column | LUM-TCMgmtNameString | .1.3.6.1.4.1.8708.2.27.2.2.1.1.2 |
| clientIfRateLimit Rate limit of link in 1,000,000 bits
(Mb) per second.
Zero (0) is a special value meaning that the
rate-limiting procedure is disabled.
The legal ran… | column | Integer32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.20 |
| clientIfAutoNegotiationMode The wanted auto negotiation mode.
off - auto negotiation process is disabled
on - auto negotiation process is enabled | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.21 |
| clientIfAutoNegotiationStatus The result of the auto negotiation procedure
incomplete - the result is still pending
half - half duplex
full - full duplex | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.22 |
| clientIfDuplexCapability The duplex capability of the HW.
half - supports half duplex
full - supports full duplex | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.23 |
| clientIfFlowControlMode The mode for handling flow control between
the local device and link partner.
The PAUSE settings has the following meaning
when auto-negotiation is enabled.
… | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.24 |
| clientIfInterPacketGap Time between the frames in nano seconds.
Legal values are 64, 72, 80, ... 200, 320, 328,
336, ... 456 | column | Unsigned32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.25 |
| clientIfFrameSize The maximum size of the transmitted and
received frames (in bytes). | column | Unsigned32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.26 |
| clientIfTrxClass String that describes the transceiver class. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.27.2.2.1.1.27 |
| clientIfLaserBias Measures laser bias current value in tenths of
mA (0.1 mA). | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.28 |
| clientIfPowerLevel The received power level in units of 0.1 dBm. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.29 |
| clientIfDescr User configurable label.
This attribute can be written via SNMP. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.27.2.2.1.1.3 |
| clientIfReceiverSensitivity The lowest power that the receiver is guaranteed
to handle, in units of 0.1 dBm. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.30 |
| clientIfPowerLevelLowRelativeThreshold The lower threshold for received power level in
units of 0.1 dB, relative to the receiver
sensitivity. | column | Integer32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.31 |
| clientIfLossOfSignal Loss of signal.
Applicable for all signal formats.
A(ctivation): Active loss of signal HW
indication.
D(e-activation): Inactive loss of signal HW
ind… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.32 |
| clientIfLossOfFrame Loss of frame.
All forms of sync loss. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.33 |
| clientIfBitrateMismatch Bitrate mismatch (Other).
Applicable for other signal formats.
D: The interface is unable to lock to the
inserted signal.
D: The interface is able to… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.34 |
| clientIfAuAlarmIndicationSignalW2C Alarm indication signal (AIS) on the trunk-side.
Applicable for SDH/Sonet signal formats.
A: An 'all ones' SDH signal is detected.
D: SDH signal reco… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.35 |
| clientIfTransmitterFailed The transceiver HW has detected a failure
in the transmitter part.
A: The transmitter has failed
D: The transmitter is OK again | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.36 |
| clientIfTrxCodeMismatch The inserted transceiver does not have a legal
manufacturer code.
A: A transceiver with illegal code is inserted.
D: The transceiver with illegal cod… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.37 |
| clientIfTrxBitrateUnavailable The inserted transceiver does not support the
requested bit rate.
A: A transceiver with other supported bit rate than
the requested bit rate is inserted.
… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.38 |
| clientIfTrxMissing An expected transceiver is missing.
A: An expected transceiver is missing.
D: The missing transceiver is inserted. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.39 |
| clientIfSubrack The number of the subrack where the interface
is located. | column | LUM-TCSubrackNumber | .1.3.6.1.4.1.8708.2.27.2.2.1.1.4 |
| clientIfReceivedPowerHigh Received power level is too high.
Applicable for all signal formats.
A: The received power level exceeds the
the built-in overload threshold.
D: The … | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.40 |
| clientIfReceivedPowerLow Received power level low threshold exceeded.
Applicable for all signal formats.
A: The received power level is below the
associated threshold.
D: The… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.41 |
| clientIfLinkDown A: Failure to negotiate a connection with the
other party.
D: A connection is negotiated. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.42 |
| clientIfConfigurationCommand Command to change the signal format, and, if
applicable, also the mode (framed, transparent). | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.27.2.2.1.1.43 |
| clientIfGbeUtilization Shows the current bandwidth utilization
measured at the physical (802.3 PHY) layer.
The value represents a snapshot of the utilization
during the latest second. It is expressed i… | column | Unsigned32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.44 |
| clientIfLossOfSync Loss of sync.
All forms of sync loss.
A: GbE 'frame' can not be located.
D: GbE 'frame' is located. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.45 |
| clientIfConfigureTrxModeCommand Command to change the TRX mode (client or line) and/or
TRX media (optical or electrical). | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.27.2.2.1.1.46 |
| clientIfTrxMode Shows if the port is configured as:
- normal CLIENT interface connected to a non XTM Series
client equipment, with non-colored, or colored TRXes.
-… | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.47 |
| clientIfExpectedTxFrequency The expected frequency given in hundreds of GHz
(0.01 GHz). | column | LUM-TCLambdaFrequency | .1.3.6.1.4.1.8708.2.27.2.2.1.1.48 |
| clientIfTxFrequency The transmitted frequency given in hundreds of
GHz (0.01 GHz). | column | LUM-TCLambdaFrequency | .1.3.6.1.4.1.8708.2.27.2.2.1.1.49 |
| clientIfSlot The number of the slot where the interface is
located. | column | LUM-TCSlotNumber | .1.3.6.1.4.1.8708.2.27.2.2.1.1.5 |
| clientIfUnexpectedTxFrequency The actual frequency does not match the
pre-configured frequency.
A pre-configured frequency of '0' matches
all actual frequencies.
A: The configured… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.50 |
| clientIfIllegalFrequency The frequency supported by the transceiver is not
recognized by the system.
A: Invalid or unknown frequency information is
detected in the (pluggable) transceive… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.51 |
| clientIfLaserForcedOn When enabled, the laser is on regardless of whether
there is a trunc signal present or not.
disabled - the laser is only on when there is a
trunc signal.… | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.52 |
| clientIfTrxMedia Defines the media and capability of the TRX. | column | LUM-TCTrxMedia | .1.3.6.1.4.1.8708.2.27.2.2.1.1.53 |
| clientIfTrxMediaMismatch The TRX media does not match the expected one.
A: Invalid or mismatching trx media is
detected.
D: The (pluggable) transceiver or board is
repl… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.54 |
| clientIfTruncAutoNegotiationMode Decides whether auto negotiation shall
be performed over the trunc connection.
This is applicable when the terminating
node at the other side of the
trunc is config… | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.55 |
| clientIfObjectProperty Property mask. | column | LUM-TCObjectProperty | .1.3.6.1.4.1.8708.2.27.2.2.1.1.56 |
| clientIfTxPowerLevel The transmitted power level in units of 0.1 dBm. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.57 |
| clientIfLaserTempActual The actual laser temperature in units of
0.1 degrees centigrade. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.58 |
| clientIfTraceIntrusionMode Indicates whether the trace identifier should be
inserted into the transmitted signal or to be
transparent.
disabled - The trace identifier is taken from
the recevi… | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.59 |
| clientIfTxPort The number of the port where the TX-side of the
interface is located. | column | LUM-TCPortNumber | .1.3.6.1.4.1.8708.2.27.2.2.1.1.6 |
| clientIfTraceTransmitted The trace identifier to be transmitted from this
interface.
The identifier length is by default 0 to 15. For
mxp8iiSonet board the length i 0 to 62.
… | column | OctetString | .1.3.6.1.4.1.8708.2.27.2.2.1.1.60 |
| clientIfTraceReceived The received trace identifier for this interface. | column | OctetString | .1.3.6.1.4.1.8708.2.27.2.2.1.1.61 |
| clientIfTraceExpected Trace identifier used for matching against
the received trace identifier.
The identifier length is by default 0 to 15. For
mxp8iiSonet board the length is 0 to 62. | column | OctetString | .1.3.6.1.4.1.8708.2.27.2.2.1.1.62 |
| clientIfTraceAlarmMode Controls if the trace identifier mismatch alarm
should be raised.
disabled - The alarm is disabled.
enabled - The alarm is raised if expected trace
i… | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.63 |
| clientIfTraceMismatch Indicates if the expected trace identifier
differs from the received trace identifier.
A: The received trace identifier differs from
the expected trace identifier.
… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.64 |
| clientIfNearEndLoopback Loop the client RX signal back to the client TX.
This is also called Facility loopback
disabled - the signal is not looped
enabled - the signal is lo… | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.65 |
| clientIfRxSignalStatus The operational state for incoming (RX) signal
of the interface.
down - A major fault has occurred
degraded - The signal quality is impaired.
… | column | LUM-TCSignalStatusWithNA | .1.3.6.1.4.1.8708.2.27.2.2.1.1.66 |
| clientIfMsAlarmIndicationSignalC2W MS Alarm indication signal (MS-AIS) on the
client side.
Applicable for SDH/Sonet signal formats.
A: An 'all ones' pattern is detected.
D: The signal … | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.67 |
| clientIfMsAlarmIndicationSignalW2C MS Alarm indication signal (MS-AIS) on the trunc
side. Applicable for SDH/Sonet/IWDM signal formats.
A: An 'all ones' pattern is detected.
D: The sig… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.68 |
| clientIfRemoteDefectIndication Remote defect indication.
Applicable for SDH/Sonet signal formats.
A: RDI indication (in SDH/Sonet frame) active.
D: RDI indication inactive. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.69 |
| clientIfRxPort The number of the port where the RX-side of the
interface is located. | column | LUM-TCPortNumber | .1.3.6.1.4.1.8708.2.27.2.2.1.1.7 |
| clientIfJ1TxTrailTrace The J1 trail trace identifier(s) to be
transmitted for the VC4s/VC3s related to this
interface, in the line signal (STM16/OC48).
This parameter can be used in two d… | column | OctetString | .1.3.6.1.4.1.8708.2.27.2.2.1.1.70 |
| clientIfJ1TxTrailTraceInsertionMode Controls how the J1 trail trace insertion
should work, i.e. how the j1TxTrailTrace
parameter shall be inserted in the line
signal.
Important: there is only one j1Tx… | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.71 |
| clientIfTrxFailed A transceiver hardware failure is detected.
A: The transceiver fails.
D: The transceiver is replaced. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.72 |
| clientIfDisabled The interface is disabled.
A: Interface disabled.
D: Interface enabled. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.73 |
| clientIfLoopback The interface is set in loopback mode.
A: Loopback enabled.
D: Loopback disabled. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.74 |
| clientIfVcGroupFailedW2C The received line signal contains a VC
mapped to this interface, that is
faulty, e.g. unequipped.
Please note that this fault is in the
LINE SIGNAL, but is presente… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.75 |
| clientIfReadJ1 Read the received J1 for the VC4/VC3 in the
STM16 frame associated to this interface.
Synopsis: readJ1 | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.27.2.2.1.1.76 |
| clientIfClientSignalFailed The received line signal contains a VC
mapped to this interface, that is
faulty, e.g. unequipped.
Please note that this fault is in the
LINE SIGNAL, but is presente… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.77 |
| clientIfAuLossOfPointer Loss of pointer. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.78 |
| clientIfGfpLossOfFrame GFP Loss of frame. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.79 |
| clientIfInvPhysIndexOrZero The row in the invPhysTable for this interface.
Set to 0 if not known. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.8 |
| clientIfHighSpeed The expected signal bit rate in units of
1,000,000 bits (Mb) per second. If this object
reports a value of 'n' then the speed of the
interface is somewhere in the range of 'n-500,… | column | Unsigned32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.80 |
| clientIfActualFormat The actual signal format. | column | LUM-TCSignalFormat | .1.3.6.1.4.1.8708.2.27.2.2.1.1.81 |
| clientIfRdiIntrusionMode Indicates whether RDI information should be
inserted in the transmitted signal.
disabled - No RDI information is inserted in the
transmitted signal.
… | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.82 |
| clientIfMuxQuadVc4 States which quadrant of the payload
that the interface is connected to
in rx direction. (outgoing line) | column | Unsigned32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.83 |
| clientIfDemuxQuadVc4 States whitch quadrant of the payload
that the interface is connected to
in tx direction. (outgoing client) | column | Unsigned32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.84 |
| clientIfCcConnectionMode controls if DemuxPayloadQuad is same
as MuxPayloadQuad
(same => connected, not same => disconnected) | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.85 |
| clientIfCcConfigurationCommand Command to change the crossconnect,
If no arguments are given, the user will be prompted. | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.27.2.2.1.1.86 |
| clientIfIllegalSignalFormat IllegalSignalFormat.
A(ctivation): Actual Format does NOT match
expected Format.
D(e-activation): Actual Format does match
expected Format. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.87 |
| clientIfSynchProtPortId The Id for this port in the synch prot group,
to identify the port. (A or B) | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.88 |
| clientIfSynchProtGroupMemberPort The port number for the TX side of the port
that is in this synch protection group. | column | LUM-TCPortNumber | .1.3.6.1.4.1.8708.2.27.2.2.1.1.89 |
| clientIfEntityId Index in entity table.
-- Only used for notifications | column | Unsigned32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.9 |
| clientIfSynchProtGroupStatus Note: This object is deprecated.
The operational state for the protection group.
bothDown - both sides down
bothUp - both sides up
… | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.90 |
| clientIfSynchProtActivePort The operational state for the protection group.
none - no side is active.
A - the A port is active.
B - the B port is active. | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.91 |
| clientIfSynchProtPortStatus The operational synch protection state
for this port in the synch protection group.
down - this port is out of service.
up - this port is active. | column | Enumeration | .1.3.6.1.4.1.8708.2.27.2.2.1.1.92 |
| clientIfSynchProtToggleActivePort Command to toggle which port is active in the synch
prot group | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.27.2.2.1.1.93 |
| clientIfNearEndLoopbackTimeout Timeout for near end loopback (a.k.a. facility
loopback) to make sure connection to node is not
lost if ppp link is broken.
The unit is hours. 0.1 means 6 minutes. | column | Integer32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.94 |
| clientIfNearEndLoopbackEnabled Near end loopback (a.k.a. facility loopback)
is enabled. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.95 |
| clientIfChangeNearEndLoopbackCommand Command to change near end loopback (a.k.a.
facility loopback) and loopbacktimeout | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.27.2.2.1.1.96 |
| clientIfFarEndLoopbackEnabled Far end loopback (a.k.a. terminal loopback)
is enabled. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.27.2.2.1.1.97 |
| clientIfFarEndLoopbackTimeout Timeout for far end loopback (a.k.a. terminal
loopback) to make sure connection to node is
not lost if ppp link is broken.
The unit is hours. 0.1 means 6 minutes. | column | Integer32 | .1.3.6.1.4.1.8708.2.27.2.2.1.1.98 |
| clientIfChangeFarEndLoopbackCommand Command to change far end loopback (a.k.a.
terminal loopback) and loopbacktimeout | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.27.2.2.1.1.99 |