l2tpDomainConfigTunnelIdleTO
L2TP-MIB ·
.1.3.6.1.2.1.10.95.1.2.1.8
Object
column
r/w
seconds Integer32
This object defines the period of time that an established tunnel belonging to this tunnel domain with no active sessions will wait before disconnecting the tunnel. A value of zero indicates that the tunnel will disconnect immediately after the last session disconnects. A value of -1 leaves the tunnel up indefinitely. This object may be modified when the administrative state is enabled for this conceptual row.
Context
- MIB
- L2TP-MIB
- OID
.1.3.6.1.2.1.10.95.1.2.1.8- Type
- column
- Access
- readwrite
- Status
- current
- Units
- seconds
- Parent
- l2tpDomainConfigEntry
- Table
- l2tpDomainConfigTable
- Siblings
- 15
Syntax
seconds Integer32
Values & Constraints
Object Constraints
range: -1-86400
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| l2tpDomainConfigId The identifier, usually in the form of a Domain
Name (full or partial), describing a single tunnel
endpoint or a domain of tunnel endpoints. This is
typically used as a 'handle' t… | column | OctetString | .1.3.6.1.2.1.10.95.1.2.1.1 |
| l2tpDomainConfigControlMaxRetx This object defines the maximum number of retransmissions
which the L2TP stack will attempt for tunnels belonging
to this domain before assuming that the peer is no
longer respond… | column | Integer32 | .1.3.6.1.2.1.10.95.1.2.1.10 |
| l2tpDomainConfigControlMaxRetxTO This object defines the maximum retransmission timeout
interval which the L2TP stack will wait for tunnels
belonging to this domain before retransmitting a
control packet that has… | column | seconds Integer32 | .1.3.6.1.2.1.10.95.1.2.1.11 |
| l2tpDomainConfigPayloadSeq This object determines whether or not session payload
packets will be requested to be sent with sequence
numbers from tunnel peers belonging to this domain.
The value onDemand(1) … | column | Enumeration | .1.3.6.1.2.1.10.95.1.2.1.12 |
| l2tpDomainConfigReassemblyTO This object defines the number of milliseconds that
local peers of this tunnel domain will wait before
processing payload packets that were received out of
sequence (which are wai… | column | L2tpMilliSeconds | .1.3.6.1.2.1.10.95.1.2.1.13 |
| l2tpDomainConfigProxyPPPAuth This object is used to configure the sending
or acceptance of the PPP Proxy Authentication
AVP's on the LAC or LNS. | column | SNMPv2-TCTruthValue | .1.3.6.1.2.1.10.95.1.2.1.14 |
| l2tpDomainConfigStorageType The storage type for this conceptual row.
Conceptual rows having the value 'permanent' must
allow write-access at a minimum to:
- l2tpDomainConfigAdm… | column | SNMPv2-TCStorageType | .1.3.6.1.2.1.10.95.1.2.1.15 |
| l2tpDomainConfigStatus The status of this Domain entry. Columnar objects
corresponding to this conceptual row may be modified
according to their description clauses when this
RowStatus object is 'active… | column | SNMPv2-TCRowStatus | .1.3.6.1.2.1.10.95.1.2.1.16 |
| l2tpDomainConfigAdminState This object defines the administrative state of this
tunnel domain. Setting this object to disabled(2)
causes all tunnels to be immediately disconnected
and no further tunnels to … | column | Enumeration | .1.3.6.1.2.1.10.95.1.2.1.2 |
| l2tpDomainConfigDrainTunnels Setting this object to 'true' will prevent any new
tunnels and/or sessions from being either initiated
or accepted but does NOT disconnect any active
tunnels/sessions for this tun… | column | SNMPv2-TCTruthValue | .1.3.6.1.2.1.10.95.1.2.1.3 |
| l2tpDomainConfigAuth This object describes how tunnel peers belonging
to this domain are to be authenticated. The value
simple(2) indicates that peers are authenticated
simply by their host name as de… | column | Enumeration | .1.3.6.1.2.1.10.95.1.2.1.4 |
| l2tpDomainConfigSecret This object is used to configure the shared secret
used during the tunnel authentication phase of
tunnel establishment. This object MUST be accessible
only via requests using both… | column | OctetString | .1.3.6.1.2.1.10.95.1.2.1.5 |
| l2tpDomainConfigTunnelSecurity This object defines whether this tunnel domain
requires that all tunnels are to be secured. The
value of ipsec(3) indicates that all tunnel packets,
control and ses… | column | Enumeration | .1.3.6.1.2.1.10.95.1.2.1.6 |
| l2tpDomainConfigTunnelHelloInt This object defines the interval in which Hello
(or keep-alive) packets are to be sent by local
peers belonging to this tunnel domain. The value
zero effectively disables the send… | column | seconds Integer32 | .1.3.6.1.2.1.10.95.1.2.1.7 |
| l2tpDomainConfigControlRWS This object defines the control channel receive
window size for tunnels belonging to this domain. It
specifies the maximum number of packets the tunnel
peer belongi… | column | Integer32 | .1.3.6.1.2.1.10.95.1.2.1.9 |