l2tpDomainConfigControlRWS
L2TP-MIB ·
.1.3.6.1.2.1.10.95.1.2.1.9
Object
column
r/w
Integer32
This object defines the control channel receive
window size for tunnels belonging to this domain. It
specifies the maximum number of packets the tunnel
peer belonging to this domain can send without waiting
for an acknowledgement from this peer.
Context
- MIB
- L2TP-MIB
- OID
.1.3.6.1.2.1.10.95.1.2.1.9- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- l2tpDomainConfigEntry
- Table
- l2tpDomainConfigTable
- Siblings
- 15
Syntax
Integer32
Values & Constraints
Object Constraints
range: 1-65535
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| l2tpDomainConfigId The identifier, usually in the form of a Domain
Name (full or partial), describing a single tunnel
endpoint or a domain of tunnel endpoints. This is
typically used as a 'handle' t… | column | OctetString | .1.3.6.1.2.1.10.95.1.2.1.1 |
| l2tpDomainConfigControlMaxRetx This object defines the maximum number of retransmissions
which the L2TP stack will attempt for tunnels belonging
to this domain before assuming that the peer is no
longer respond… | column | Integer32 | .1.3.6.1.2.1.10.95.1.2.1.10 |
| l2tpDomainConfigControlMaxRetxTO This object defines the maximum retransmission timeout
interval which the L2TP stack will wait for tunnels
belonging to this domain before retransmitting a
control packet that has… | column | seconds Integer32 | .1.3.6.1.2.1.10.95.1.2.1.11 |
| l2tpDomainConfigPayloadSeq This object determines whether or not session payload
packets will be requested to be sent with sequence
numbers from tunnel peers belonging to this domain.
The value onDemand(1) … | column | Enumeration | .1.3.6.1.2.1.10.95.1.2.1.12 |
| l2tpDomainConfigReassemblyTO This object defines the number of milliseconds that
local peers of this tunnel domain will wait before
processing payload packets that were received out of
sequence (which are wai… | column | L2tpMilliSeconds | .1.3.6.1.2.1.10.95.1.2.1.13 |
| l2tpDomainConfigProxyPPPAuth This object is used to configure the sending
or acceptance of the PPP Proxy Authentication
AVP's on the LAC or LNS. | column | SNMPv2-TCTruthValue | .1.3.6.1.2.1.10.95.1.2.1.14 |
| l2tpDomainConfigStorageType The storage type for this conceptual row.
Conceptual rows having the value 'permanent' must
allow write-access at a minimum to:
- l2tpDomainConfigAdm… | column | SNMPv2-TCStorageType | .1.3.6.1.2.1.10.95.1.2.1.15 |
| l2tpDomainConfigStatus The status of this Domain entry. Columnar objects
corresponding to this conceptual row may be modified
according to their description clauses when this
RowStatus object is 'active… | column | SNMPv2-TCRowStatus | .1.3.6.1.2.1.10.95.1.2.1.16 |
| l2tpDomainConfigAdminState This object defines the administrative state of this
tunnel domain. Setting this object to disabled(2)
causes all tunnels to be immediately disconnected
and no further tunnels to … | column | Enumeration | .1.3.6.1.2.1.10.95.1.2.1.2 |
| l2tpDomainConfigDrainTunnels Setting this object to 'true' will prevent any new
tunnels and/or sessions from being either initiated
or accepted but does NOT disconnect any active
tunnels/sessions for this tun… | column | SNMPv2-TCTruthValue | .1.3.6.1.2.1.10.95.1.2.1.3 |
| l2tpDomainConfigAuth This object describes how tunnel peers belonging
to this domain are to be authenticated. The value
simple(2) indicates that peers are authenticated
simply by their host name as de… | column | Enumeration | .1.3.6.1.2.1.10.95.1.2.1.4 |
| l2tpDomainConfigSecret This object is used to configure the shared secret
used during the tunnel authentication phase of
tunnel establishment. This object MUST be accessible
only via requests using both… | column | OctetString | .1.3.6.1.2.1.10.95.1.2.1.5 |
| l2tpDomainConfigTunnelSecurity This object defines whether this tunnel domain
requires that all tunnels are to be secured. The
value of ipsec(3) indicates that all tunnel packets,
control and ses… | column | Enumeration | .1.3.6.1.2.1.10.95.1.2.1.6 |
| l2tpDomainConfigTunnelHelloInt This object defines the interval in which Hello
(or keep-alive) packets are to be sent by local
peers belonging to this tunnel domain. The value
zero effectively disables the send… | column | seconds Integer32 | .1.3.6.1.2.1.10.95.1.2.1.7 |
| l2tpDomainConfigTunnelIdleTO This object defines the period of time that an
established tunnel belonging to this tunnel
domain with no active sessions will wait before
disconnecting the tunnel. A value of zer… | column | seconds Integer32 | .1.3.6.1.2.1.10.95.1.2.1.8 |