jnxPingCtlTrapGeneration
JUNIPER-PING-MIB ·
.1.3.6.1.4.1.2636.3.7.1.2.1.16
Object
column
r/w
Bits
The value of this object determines when and if
to generate a notification for this entry:
rttThreshold(0) - Generate a jnxPingRttThresholdExceeded
notification when the configured rtt threshold
is exceeded.
rttStdDevThreshold(1) - Generate a jnxPingRttStdDevThresholdExceeded
notification when the configured rtt standard deviation
threshold is exceeded.
rttJitterThreshold(2) - Generate a jnxPingRttJitterThresholdExceeded
notification when the configured rtt jitter threshold
is exceeded.
egressThreshold(3) - Generate a jnxPingEgressThresholdExceeded
notification when the configured egress threshold is exceeded.
This applies only if the probe type supports one way measurments.
egressStdDevThreshold(4) - Generate a
jnxPingEgressStdDevThresholdExceeded notification when the
configured egress standard deviation threshold is exceeded.
This applies only if the probe type supports one way measurments.
egressJitterThreshold(5) - Generate a
jnxPingEgressJitterThresholdExceeded notification when the
configured egress jitter threshold is exceeded.
This applies only if the probe type supports one way measurments.
ingressThreshold(6) - Generate a jnxPingIngressThresholdExceeded
notification when the configured ingress threshold is exceeded.
This applies only if the probe type supports one way measurments.
ingressStdDevThreshold(7) - Generate a
jnxPingIngressStdDevThresholdExceeded notification when the
configured ingress standard deviation threshold is exceeded.
This applies only if the probe type supports one way measurments.
ingressJitterThreshold(8) - Generate a
jnxPingIngressJitterThresholdExceeded notification when the
configured ingress jitter threshold is exceeded.
This applies only if the probe type supports one way measurments.
The value of this object defaults to zero, indicating
that none of the above options have been selected.
maxrttThreshold(9) - Generate a jnxPingMaxRttThresholdExceeded
notification at the end of test session when rtt of any of the probe
exceeds the configured rtt threshold.
Context
- MIB
- JUNIPER-PING-MIB
- OID
.1.3.6.1.4.1.2636.3.7.1.2.1.16- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- jnxPingCtlEntry
- Table
- jnxPingCtlTable
- Siblings
- 22
Syntax
Bits
Values & Constraints
Enumerated Values
0 | rttThreshold |
1 | rttStdDevThreshold |
2 | rttJitterThreshold |
3 | egressThreshold |
4 | egressStdDevThreshold |
5 | egressJitterThreshold |
6 | ingressThreshold |
7 | ingressStdDevThreshold |
8 | ingressJitterThreshold |
9 | maxrttThreshold |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| jnxPingCtlOwnerIndex To facilitate the provisioning of access control by a
security administrator using the View-Based Access
Control Model (RFC 2575, VACM) for tables in which
multiple users may need… | column | OctetString | .1.3.6.1.4.1.2636.3.7.1.2.1.1 |
| jnxPingCtlEgressTimeThreshold Maximum egress trip time allowed. If this threshold is crossed by
any probe, a jnxPingEgressThresholdExceeded trap will be sent.
This applies only if the probe type (pingCtlType)… | column | microseconds Unsigned32 | .1.3.6.1.4.1.2636.3.7.1.2.1.10 |
| jnxPingCtlEgressStdDevThreshold The maximum egress trip time standard deviation allowed over the
course of any test. If the calculated standard deviation of the
egress trip time at the end of any test exceeds t… | column | microseconds Unsigned32 | .1.3.6.1.4.1.2636.3.7.1.2.1.11 |
| jnxPingCtlEgressJitterThreshold The maximum allowed jitter in the egress trip time over the course
of any test. Jitter is defined as the difference between the
maximum and minimum egress trip times measured ove… | column | microseconds Unsigned32 | .1.3.6.1.4.1.2636.3.7.1.2.1.12 |
| jnxPingCtlIngressTimeThreshold Maximum ingress trip time allowed. If this threshold is crossed by
any probe, a jnxPingIngressThresholdExceeded trap will be sent.
This applies only if the probe type (pingCtlTyp… | column | microseconds Unsigned32 | .1.3.6.1.4.1.2636.3.7.1.2.1.13 |
| jnxPingCtlIngressStddevThreshold The maximum ingress trip time standard deviation allowed over the
course of any test. If the calculated standard deviation of the
ingress trip time at the end of any test exceeds… | column | microseconds Unsigned32 | .1.3.6.1.4.1.2636.3.7.1.2.1.14 |
| jnxPingCtlIngressJitterThreshold The maximum allowed jitter in the ingress trip time over the course
of any test. Jitter is defined as the difference between the
maximum and minimum ingress trip times measured o… | column | microseconds Unsigned32 | .1.3.6.1.4.1.2636.3.7.1.2.1.15 |
| jnxPingCtlTargetPort The target UDP/TCP port used by the probe.
When ICMP ping is used, jnxPingCtlTargetPort value will be shown as 0. | column | Unsigned32 | .1.3.6.1.4.1.2636.3.7.1.2.1.17 |
| jnxPingCtlJseriesHWTimeStamp Use to enable the RPM Hardware Timestamp feature on J-series routers.
For M/T series routers, use the jnxPingCtlIfName and
pingCtlByPassRouteTable objects to redirect probes to t… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2636.3.7.1.2.1.18 |
| jnxPingCtlOneWayHWTimeStamp Use this object to enable Hardware Timestamp-based one-way
measurements. If this object is not enabled (ie, set to true),
no Hardware Timestamp based one way measurements or calc… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2636.3.7.1.2.1.19 |
| jnxPingCtlTestName The name of the ping test. This is locally unique, within
the scope of an pingCtlOwnerIndex. | column | OctetString | .1.3.6.1.4.1.2636.3.7.1.2.1.2 |
| jnxPingCtlMovAvgSize The Juniper RPM feature maintains a set of the most recent probe
measurements & provides the same calculations over that collection
as provided over a test (ie, average, standard … | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2636.3.7.1.2.1.20 |
| jnxPingCtlMXseriesHWTimeStamp Use to enable the RPM Hardware Timestamp feature on MX-series routers.
For M/T series routers, use the jnxPingCtlIfName and
pingCtlByPassRouteTable objects to redirect probes to … | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2636.3.7.1.2.1.21 |
| jnxPingCtlEXseriesHWTimeStamp Use to enable the RPM Hardware Timestamp feature on EX-series switches.
For thoses, this object must have the value: false. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2636.3.7.1.2.1.22 |
| jnxPingMaxRttThreshold Maximum round trip time allowed. If this threshold is crossed
by any probe of a test, a jnxPingMaxRttThresholdExceeded trap will be sent. | column | microseconds Unsigned32 | .1.3.6.1.4.1.2636.3.7.1.2.1.23 |
| jnxPingCtlIfName Setting this object to an interface name prior to starting a remote
ping operation directs the ping probes to be transmitted over the
specified interface. To specify the interfac… | column | OctetString | .1.3.6.1.4.1.2636.3.7.1.2.1.3 |
| jnxPingCtlRoutingIfIndex deprecated Use this option to specify the routing instance used when directing
outgoing ping packets. The interface ifIndex specified should be in
the desired routing instance table. The i… | column | IF-MIBInterfaceIndexOrZero | .1.3.6.1.4.1.2636.3.7.1.2.1.4 |
| jnxPingCtlRoutingIfName deprecated Use this option to specify the routing instance used when directing
outgoing ping packets. The interface name specified should be in
the desired routing instance table. The inte… | column | OctetString | .1.3.6.1.4.1.2636.3.7.1.2.1.5 |
| jnxPingCtlRoutingInstanceName Use this option to specify the name of the routing instance used when
directing outgoing ping packets. The instance name specified must be
configured under routing-instances of t… | column | OctetString | .1.3.6.1.4.1.2636.3.7.1.2.1.6 |
| jnxPingCtlRttThreshold Maximum round trip time allowed. If this threshold is crossed
by any probe, a jnxPingRttThresholdExceeded trap will be sent. | column | microseconds Unsigned32 | .1.3.6.1.4.1.2636.3.7.1.2.1.7 |
| jnxPingCtlRttStdDevThreshold The maximum round trip time standard deviation allowed over the
course of any test. If the calculated standard deviation of the
round trip time at the end of any test exceeds thi… | column | microseconds Unsigned32 | .1.3.6.1.4.1.2636.3.7.1.2.1.8 |
| jnxPingCtlRttJitterThreshold The maximum allowed jitter in the round trip time over the course
of any test. Jitter is defined as the difference between the
maximum and minimum round trip times measured over … | column | microseconds Unsigned32 | .1.3.6.1.4.1.2636.3.7.1.2.1.9 |