jnxoptIfOTUkTraceIdentifierAccepted
JNX-OPT-IF-MIB ·
.1.3.6.1.4.1.2636.3.73.1.1.7.1.1.6
Object
column
JnxoptIfAcTI
The actual trace identifier accepted. This object is only applicable to the sink function, i.e., only when jnxoptIfOTUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where jnxoptIfOTUkDirectionality has the value source(2). The value of this object is unspecified when jnxoptIfOTUkCurrentStatus indicates a near-end defect (i.e., ssf(3), lof(4), ais(5), lom(6)) that prevents extraction of the trace message.
Context
- MIB
- JNX-OPT-IF-MIB
- OID
.1.3.6.1.4.1.2636.3.73.1.1.7.1.1.6- Type
- column
- Access
- readonly
- Status
- current
- Parent
- jnxoptIfOTUkConfigEntry
- Table
- jnxoptIfOTUkConfigTable
- Siblings
- 13
Syntax
JnxoptIfAcTI
- Source
- JnxoptIfAcTI
- Base type
OctetString
Values & Constraints
Type Constraints
range: 64
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| jnxoptIfOTUkDirectionality Indicates the directionality of the entity. | column | JnxoptIfDirectionality | .1.3.6.1.4.1.2636.3.73.1.1.7.1.1.1 |
| jnxoptIfOTUkDEGM Indicates the threshold level for declaring a Degraded Signal
defect (dDEG). A dDEG shall be declared if jnxoptIfOTUkDEGM
consecutive bad PM Seconds are detected.
This object i… | column | JnxoptIfDEGM | .1.3.6.1.4.1.2636.3.73.1.1.7.1.1.10 |
| jnxoptIfOTUkSinkAdaptActive Indicates whether the sink adaptation function is activated or
not.
This object is only applicable to the sink function, i.e.,
only when jnxoptIfOTUkDirectionality has the valu… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2636.3.73.1.1.7.1.1.11 |
| jnxoptIfOTUkSourceAdaptActive Indicates whether the source adaptation function is activated or
not.
This object is only applicable to the source function, i.e.,
only when jnxoptIfOTUkDirectionality has the … | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2636.3.73.1.1.7.1.1.12 |
| jnxoptIfOTUkSinkFECEnabled If Forward Error Correction (FEC) is supported, this object
indicates whether FEC at the OTUk sink adaptation function is
enabled or not.
This object is only applicable to the … | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2636.3.73.1.1.7.1.1.13 |
| jnxoptIfOTUkCurrentStatus Indicates the defect condition of the entity, if any.
This object is only applicable to the sink function, i.e.,
only when jnxoptIfOTUkDirectionality has the value sink(1)
or b… | column | Bits | .1.3.6.1.4.1.2636.3.73.1.1.7.1.1.14 |
| jnxoptIfOTUkBitRateK Indicates the bit rate of the entity. | column | JnxoptIfBitRateK | .1.3.6.1.4.1.2636.3.73.1.1.7.1.1.2 |
| jnxoptIfOTUkTraceIdentifierTransmitted The trace identifier transmitted.
This object is applicable when jnxoptIfOTUkDirectionality
has the value source(2) or bidirectional(3). It must not
be instantiated in rows whe… | column | JnxoptIfTxTI | .1.3.6.1.4.1.2636.3.73.1.1.7.1.1.3 |
| jnxoptIfOTUkDAPIExpected The DAPI expected by the receiver.
This object is only applicable to the sink function, i.e.,
only when jnxoptIfOTUkDirectionality has the value sink(1)
or bidirectional(3). It… | column | JnxoptIfExDAPI | .1.3.6.1.4.1.2636.3.73.1.1.7.1.1.4 |
| jnxoptIfOTUkSAPIExpected The SAPI expected by the receiver.
This object is only applicable to the sink function, i.e.,
only when jnxoptIfOTUkDirectionality has the value sink(1)
or bidirectional(3). It… | column | JnxoptIfExSAPI | .1.3.6.1.4.1.2636.3.73.1.1.7.1.1.5 |
| jnxoptIfOTUkTIMDetMode Indicates the mode of the Trace Identifier Mismatch (TIM)
Detection function.
This object is only applicable to the sink function, i.e.,
only when jnxoptIfOTUkDirectionality ha… | column | JnxoptIfTIMDetMode | .1.3.6.1.4.1.2636.3.73.1.1.7.1.1.7 |
| jnxoptIfOTUkTIMActEnabled Indicates whether the Trace Identifier Mismatch (TIM)
Consequent Action function is enabled.
This object is only applicable to the sink function, i.e.,
only when jnxoptIfOTUkDi… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2636.3.73.1.1.7.1.1.8 |
| jnxoptIfOTUkDEGThr Indicates the threshold level for declaring a performance
monitoring (PM) Second to be bad. A PM Second is declared bad if
the percentage of detected errored blocks in that seco… | column | percentage JnxoptIfDEGThr | .1.3.6.1.4.1.2636.3.73.1.1.7.1.1.9 |