ieee8021TeipsIpgConfigCommandAdmin
IEEE8021-TEIPS-MIB ·
.1.3.111.2.802.1.1.24.1.4.1.4
Object
This column is used by the operator to request that the IPG state machine perform some administrative operation. The operator requests a command by writing the command value to this column. The state machine indicates the command that it is performing by setting the value of the CommandStatus column of this table. This column always reads back as clear(1).
Context
- MIB
- IEEE8021-TEIPS-MIB
- OID
.1.3.111.2.802.1.1.24.1.4.1.4- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- ieee8021TeipsIpgConfigEntry
- Table
- ieee8021TeipsIpgConfigTable
- Siblings
- 10
Syntax
IEEE8021-TC-MIBIEEE8021TeipsIpgConfigAdmin
- Source
- IEEE8021-TC-MIBIEEE8021TeipsIpgConfigAdmin
- Base type
Enumeration
Values & Constraints
Type Values
1 | clear |
2 | lockOutProtection |
3 | forceSwitch |
4 | manualSwitchToProtection |
5 | manualSwitchToWorking |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| ieee8021TeipsIpgConfigState This column indicates the current state of the
protection switching state machine for an IPG.
The value can be one of the following:
workingSegment(1) The prote… | column | Enumeration | .1.3.111.2.802.1.1.24.1.4.1.1 |
| ieee8021TeipsIpgConfigNotifyEnable This column is used to enable or disable transmission
of ieee8021TeipsIpgAdminFailure notifications.
These notifications are generated whenever an
administrative command cannot be… | column | SNMPv2-TCTruthValue | .1.3.111.2.802.1.1.24.1.4.1.10 |
| ieee8021TeipsIpgConfigStorageType This object indicates the persistence of this entry. For
permanent objects the ieee8021TeipsIpgConfigCommandAdmin
column must be writable. | column | SNMPv2-TCStorageType | .1.3.111.2.802.1.1.24.1.4.1.11 |
| ieee8021TeipsIpgConfigCommandStatus This column indicates the status of
administrative commands within the
protection group. It reflects the current
operational administrative command being
acted upon by the IPG. | column | IEEE8021-TC-MIBIEEE8021TeipsIpgConfigAdmin | .1.3.111.2.802.1.1.24.1.4.1.2 |
| ieee8021TeipsIpgConfigCommandLast This column indicates the last attempted administrative
command applied to the IPG. It is changed
whenever a write is made to the CommandAdmin column of
this table and is essenti… | column | IEEE8021-TC-MIBIEEE8021TeipsIpgConfigAdmin | .1.3.111.2.802.1.1.24.1.4.1.3 |
| ieee8021TeipsIpgConfigActiveRequests This column shows the status of active requests
associated with the IPG. | column | IEEE8021-TC-MIBIEEE8021TeipsIpgConfigActiveRequests | .1.3.111.2.802.1.1.24.1.4.1.5 |
| ieee8021TeipsIpgConfigWTR This column is used to configure the
wait-to-restore timer for the IPG operation.
The timer may be configured in steps of 1 minute
between 5 and 12 minutes, the default being 5.
A… | column | minutes Unsigned32 | .1.3.111.2.802.1.1.24.1.4.1.6 |
| ieee8021TeipsIpgConfigHoldOff This column is used to configure the hold off
timer. The purpose is to allow IPS to fix the problem
before a higher-layer mechanism, such as PBB-TE TESI
protection, is invoked or… | column | deciseconds Unsigned32 | .1.3.111.2.802.1.1.24.1.4.1.7 |
| ieee8021TeipsIpgM1ConfigState This column indicates the current state of the M:1 protection
switching state machine for an IPG if M:1 IPS is supported.
The value can be one of the following:
psA… | column | Enumeration | .1.3.111.2.802.1.1.24.1.4.1.8 |
| ieee8021TeipsIpgConfigMWTR This column is used to configure the M:1 wait-to-restore
timer for the IPG operation if M:1 protection is
supported. The timer may be configured in steps of
1 minute between 5 an… | column | minutes Unsigned32 | .1.3.111.2.802.1.1.24.1.4.1.9 |