hwTdmShdslConfThreshSNRMargin
HUAWEI-TDMCPE-MIB ·
.1.3.6.1.4.1.2011.5.30.1.3.1.1.1.7
Object
column
r/w
dB Integer32
This object configures the SNR margin alarm threshold.
Context
- MIB
- HUAWEI-TDMCPE-MIB
- OID
.1.3.6.1.4.1.2011.5.30.1.3.1.1.1.7- Type
- column
- Access
- readwrite
- Status
- current
- Units
- dB
- Parent
- hwTdmShdslConfEntry
- Table
- hwTdmShdslConfTable
- Siblings
- 9
Syntax
dB Integer32
Values & Constraints
Object Constraints
range: 0-15
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| hwTdmShdslConfPowerBackOff This object configures the receiver at the associated
segment endpoint to operate in power backoff mode.
Options:
1. enable(1) - Indicates that enable the function.
2. disable(2)… | column | Enumeration | .1.3.6.1.4.1.2011.5.30.1.3.1.1.1.1 |
| hwTdmShdslConfTestCmd Setting this object to a value as detailed further on
will initiate a test on the specific port.
The terminology and order of the … | column | Enumeration | .1.3.6.1.4.1.2011.5.30.1.3.1.1.1.10 |
| hwTdmShdslConfWorstCaseSNRMargin This object specifies the upstream worst case target SNR
margin for a SHDSL line. The SNR margin is the difference
between the desired SNR and the actual SNR. Target SNR
margin… | column | dB Integer32 | .1.3.6.1.4.1.2011.5.30.1.3.1.1.1.2 |
| hwTdmShdslConfCurrentSNRMargin This object specifies the upstream current condition
target SNR margin for a SHDSL line. The SNR margin is the
difference between the desired SNR and the actual SNR.
Target SN… | column | dB Integer32 | .1.3.6.1.4.1.2011.5.30.1.3.1.1.1.3 |
| hwTdmShdslConfPSD This object configures use of symmetric/asymmetric PSD
(Power Spectral Density) Mask for the associated SHDSL Line.
Support for symmetric PSD is mandatory for all supported
da… | column | Enumeration | .1.3.6.1.4.1.2011.5.30.1.3.1.1.1.4 |
| hwTdmShdslConfLineProbe This object enables/disables support for Line Probe of
the units in a SHDSL line. When Line Probe is enabled,
the system performs Line Probing to find the best possible
rate (… | column | Enumeration | .1.3.6.1.4.1.2011.5.30.1.3.1.1.1.5 |
| hwTdmShdslConfThreshLoopAttenuation This object configures the loop attenuation alarm threshold. | column | dB Integer32 | .1.3.6.1.4.1.2011.5.30.1.3.1.1.1.6 |
| hwTdmShdslConfWireInterface This object configures the two-wire or optional four-wire
operation for SHDSL Lines.
Options:
1. twoWire(1) - Indicates that the operation for SHDSL Lines is two-wire.
2. fourWir… | column | Enumeration | .1.3.6.1.4.1.2011.5.30.1.3.1.1.1.8 |
| hwTdmShdslConfTestTimeout This object is applicable only when a single test is
running. It indicates the test activation timeout in
minutes. When the timeout expires, the test is stopped.
Value of 0 indi… | column | Integer32 | .1.3.6.1.4.1.2011.5.30.1.3.1.1.1.9 |