hwTdmShdslConfPSD
HUAWEI-TDMCPE-MIB ·
.1.3.6.1.4.1.2011.5.30.1.3.1.1.1.4
Object
column
Enumeration
This object configures use of symmetric/asymmetric PSD (Power Spectral Density) Mask for the associated SHDSL Line. Support for symmetric PSD is mandatory for all supported data rates. Support for asymmetric PSD is optional. Options: 1. asymDisable(0) - Indicates that PSD asymmetric disable. 2. asymEnable(1) - Indicates that PSD asymmetric enable. 3. r1AsymEnable(2) - Indicates that PSD r1 asymmetric enable. 4. r2AsymEnable(3) - Indicates that PSD r2 asymmetric enable. 5. asymSymEnable(4) - Indicates that PSD asymmetric and symmetric enable. 6. psdUnknown(5) - Indicates that PSD unknown.
Context
- MIB
- HUAWEI-TDMCPE-MIB
- OID
.1.3.6.1.4.1.2011.5.30.1.3.1.1.1.4- Type
- column
- Access
- readonly
- Status
- current
- Parent
- hwTdmShdslConfEntry
- Table
- hwTdmShdslConfTable
- Siblings
- 9
Syntax
Enumeration
Values & Constraints
Enumerated Values
0 | asymDisable |
1 | asymEnable |
2 | r1AsymEnable |
3 | r2AsymEnable |
4 | asymSymEnable |
5 | psdUnknown |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| hwTdmShdslConfPowerBackOff This object configures the receiver at the associated
segment endpoint to operate in power backoff mode.
Options:
1. enable(1) - Indicates that enable the function.
2. disable(2)… | column | Enumeration | .1.3.6.1.4.1.2011.5.30.1.3.1.1.1.1 |
| hwTdmShdslConfTestCmd Setting this object to a value as detailed further on
will initiate a test on the specific port.
The terminology and order of the … | column | Enumeration | .1.3.6.1.4.1.2011.5.30.1.3.1.1.1.10 |
| hwTdmShdslConfWorstCaseSNRMargin This object specifies the upstream worst case target SNR
margin for a SHDSL line. The SNR margin is the difference
between the desired SNR and the actual SNR. Target SNR
margin… | column | dB Integer32 | .1.3.6.1.4.1.2011.5.30.1.3.1.1.1.2 |
| hwTdmShdslConfCurrentSNRMargin This object specifies the upstream current condition
target SNR margin for a SHDSL line. The SNR margin is the
difference between the desired SNR and the actual SNR.
Target SN… | column | dB Integer32 | .1.3.6.1.4.1.2011.5.30.1.3.1.1.1.3 |
| hwTdmShdslConfLineProbe This object enables/disables support for Line Probe of
the units in a SHDSL line. When Line Probe is enabled,
the system performs Line Probing to find the best possible
rate (… | column | Enumeration | .1.3.6.1.4.1.2011.5.30.1.3.1.1.1.5 |
| hwTdmShdslConfThreshLoopAttenuation This object configures the loop attenuation alarm threshold. | column | dB Integer32 | .1.3.6.1.4.1.2011.5.30.1.3.1.1.1.6 |
| hwTdmShdslConfThreshSNRMargin This object configures the SNR margin alarm threshold. | column | dB Integer32 | .1.3.6.1.4.1.2011.5.30.1.3.1.1.1.7 |
| hwTdmShdslConfWireInterface This object configures the two-wire or optional four-wire
operation for SHDSL Lines.
Options:
1. twoWire(1) - Indicates that the operation for SHDSL Lines is two-wire.
2. fourWir… | column | Enumeration | .1.3.6.1.4.1.2011.5.30.1.3.1.1.1.8 |
| hwTdmShdslConfTestTimeout This object is applicable only when a single test is
running. It indicates the test activation timeout in
minutes. When the timeout expires, the test is stopped.
Value of 0 indi… | column | Integer32 | .1.3.6.1.4.1.2011.5.30.1.3.1.1.1.9 |