hwGBondGroupProfTargetDataRateDs
HUAWEI-GBOND-MIB ·
.1.3.6.1.4.1.2011.6.137.6.1.11
Object
column
r/w
Kbps Unsigned32
A desired G.Bond port data rate in the downstream direction,
in Kbps, to be achieved during initialization, under
restrictions placed upon the member BCEs by their respective
configuration settings. This object represents a sum of individual
BCE downstream data rates, modified to compensate for fragmentation
and encapsulation overhead (e.g., for an Ethernet service, the
target data rate of 10Mbps shall allow lossless transmission
of full-duplex 10Mbps Ethernet frame stream with minimal inter-frame gap).
The value between 64 and 1000000 indicates that the total
downstream data rate of the G.Bond port after initialization
SHALL be equal to the target data rate or less, if the target
downstream data rate cannot be achieved under the restrictions
configured for BCEs. In case the copper environment allows to
achieve higher downstream data rate than that specified by
this object, the excess capability shall be either converted
to additional SNR margin or reclaimed by minimizing transmit power.
The value of 0 means that the target data rate is not
fixed and SHALL be set to the maximum attainable rate during
initialization (Best Effort), under specified spectral
restrictions and with desired SNR Margin per BCE.
Context
- MIB
- HUAWEI-GBOND-MIB
- OID
.1.3.6.1.4.1.2011.6.137.6.1.11- Type
- column
- Access
- readwrite
- Status
- current
- Units
- Kbps
- Parent
- hwGBondGroupProfEntry
- Table
- hwGBondGroupProfTable
- Siblings
- 15
Syntax
Kbps Unsigned32
Values & Constraints
Object Constraints
range: 0-0
range: 64-1000000
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| hwGBondGroupProfName This object identifies a row in this table. | column | OctetString | .1.3.6.1.4.1.2011.6.137.6.1.1 |
| hwGBondGroupProfTargetDataRateUs A desired G.Bond port data rate in the upstream direction,
in Kbps, to be achieved during initialization, under
restrictions placed upon the member BCEs by their respective
config… | column | Kbps Unsigned32 | .1.3.6.1.4.1.2011.6.137.6.1.10 |
| hwGBondGroupProfThreshLowDataRateUs This object configures the G.Bond port low upstream rate
crossing alarm threshold. The value of 0 means that the
low upstream data rate is not fixed. | column | Kbps Unsigned32 | .1.3.6.1.4.1.2011.6.137.6.1.12 |
| hwGBondGroupProfThreshLowDataRateDs This object configures the G.Bond port low downstream rate
crossing alarm threshold. The value of 0 means that the
low downstream data rate is not fixed. | column | Kbps Unsigned32 | .1.3.6.1.4.1.2011.6.137.6.1.13 |
| hwGBondGroupProfLowRateCrossingEnable Indicates whether hwGBondLowUpRateCrossingAlarmTrap and hwGBondLowDownRateCrossingAlarmTrap
notifications should be generated for this interface.
Options:
1. enable(1) - I… | column | Enumeration | .1.3.6.1.4.1.2011.6.137.6.1.14 |
| hwGBondGroupProfRowStatus This object is used to create a new row or delete an existing row
in this table. Before a profile can be deleted, it must be not
referenced from all associated bonding group. | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.2011.6.137.6.1.15 |
| hwGBondGroupProfBondCpeIncorrectAlarmSwitch This object enable/disable the bonding CPE incorrect alarm switch.
Options:
1. enable(1) - The bonding CPE incorrect alarm switch is enabled
2. disable(2) - The bonding CPE inco… | column | Enumeration | .1.3.6.1.4.1.2011.6.137.6.1.16 |
| hwGBondGroupProfMaxDelayUs This parameter is the maximum one-way interleaving delay introduced
by the PMS-TC on upstream direction. | column | milliseconds Unsigned32 | .1.3.6.1.4.1.2011.6.137.6.1.2 |
| hwGBondGroupProfMaxDelayDs This parameter is the maximum one-way interleaving delay introduced
by the PMS-TC on downstream direction. | column | milliseconds Unsigned32 | .1.3.6.1.4.1.2011.6.137.6.1.3 |
| hwGBondGroupProfMinProtectionUs This parameter is minimum impulse noise protection for the bearer channel
in the upstream direction, expressed in symbols. The parameter can take the
following values: noProtecti… | column | symbols GBondSymbolProtection | .1.3.6.1.4.1.2011.6.137.6.1.4 |
| hwGBondGroupProfMinProtectionDs This parameter is minimum impulse noise protection for the bearer channel
in the downstream direction, expressed in symbols. The parameter can take the
following values: noProtec… | column | symbols GBondSymbolProtection | .1.3.6.1.4.1.2011.6.137.6.1.5 |
| hwGBondGroupProfMinDataRateUs This parameter specifics minimum data rate for the bearer channel
in the upstream direction. The value of 0 means that the minimum
upstream data rate is not fixed. | column | Kbps Unsigned32 | .1.3.6.1.4.1.2011.6.137.6.1.6 |
| hwGBondGroupProfMinDataRateDs This parameter specifics minimum data rate for the bearer channel
in the downstream direction. The value of 0 means that the minimum
downstream data rate is not fixed. | column | Kbps Unsigned32 | .1.3.6.1.4.1.2011.6.137.6.1.7 |
| hwGBondGroupProfMaxDataRateUs This parameter specifics maximum data rate for the bearer channel
in the upstream direction. The value of 0 means that the maximum
upstream data rate is not fixed. | column | Kbps Unsigned32 | .1.3.6.1.4.1.2011.6.137.6.1.8 |
| hwGBondGroupProfMaxDataRateDs This parameter specifics maximum data rate for the bearer channel
in the downstream direction. The value of 0 means that the maximum
downstream data rate is not fixed. | column | Kbps Unsigned32 | .1.3.6.1.4.1.2011.6.137.6.1.9 |