hwLoopLineTestConclusion
HUAWEI-COMMTEST-MIB ·
.1.3.6.1.4.1.2011.6.21.1.1.1.2.1.9
Object
column
Enumeration
MELT test conclusion, this object is for pots and combo board's port. Options: 1. normal(1) -the test conclusion is normal 2. meetLine(2) -the test conclusion is meetLine 3. aLineMix(3) -the test conclusion is aLineMix 4. bLineMix(4) -the test conclusion is bLineMix 5. doubleMix(5) -the test conclusion is doubleMix 6. aLineEarth(6) -the test conclusion is aLineEarth 7. bLineEarth(7) -the test conclusion is bLineEarth 8. doublelineearth(8) -the test conclusion is doublelineearth 9. selfMix(9) -the test conclusion is selfMix 10. abLine(10) -the test conclusion is abLine 11. aLineFree(11) -the test conclusion is aLineFree 12. bLineEarthFree(12) -the test conclusion is bLineEarthFree 13. doubleLineEarthFree(13) -the test conclusion is doubleLineEarthFree 14. abLineFree(14) -the test conclusion is abLineFree 15. killLine(15) -the test conclusion is killLine 16. noPutDownTele(16) -the test conclusion is noPutDownTele 17. unknow(17) -the test conclusion is unknow 18. selfMixinMDF(18) -the test conclusion is selfMixinMDF 19. selfMixoutMDF(19) -the test conclusion is selfMixoutMDF 20. cutLineinMDF(20) -the test conclusion is cutLineinMDF 21. cutLineoutMDF(21) -the test conclusion is cutLineoutMDF 22. dCvoltagePowerFeed(30) -the test conclusion is dCvoltagePowerFeed 23. aCvoltageRinging(31) -the test conclusion is aCvoltageRinging 24. dCvoltageOffhook(32) -the test conclusion is dCvoltageOffhook 25. dCvoltage(33) -the test conclusion is dCvoltage 26. aCvoltage(34) -the test conclusion is aCvoltage 27. abImpedance(35) -the test conclusion is abImpedance 28. baImpedance(36) -the test conclusion is baImpedance 29. agImpedance(37) -the test conclusion is agImpedance 30. bgImpedance(38) -the test conclusion is bgImpedance 31. agACCurrent(39) -the test conclusion is agACCurrent 32. bgACCurrent(41) -the test conclusion is bgACCurrent 33. abACCurrent(42) -the test conclusion is abACCurrent 34. agDCCurrent(43) -the test conclusion is agDCCurrent 35. bgDCCurrent(44) -the test conclusion is bgDCCurrent 36. abDCCurrent(45) -the test conclusion is abDCCurrent 37. loopCurrent(46) -the test conclusion is loopCurrent 38. noise(47) -the test conclusion is noise 39. abRFaultId(91) -the test conslusion is ab Line all fault 40. aRFaultId(92) -the test conslusion is a Line fault 41. bRFaultId(93) -the test conslusion is b Line fault 42. abLeakId(94) -the test conslusion is ab Line all leak 43. aLeakId(95) -the test conslusion is a Line leak 44. bLeakId(96) -the test conslusion is b line leak 45. abFvacLevelH(97) -the test conslusion is ab dangerous AC to ground 46. aFvacLevelH(98) -the test conslusion is a dangerous AC to ground 47. bFvacLevelH(99) -the test conslusion is b dangerous AC to ground 48. abFvacLevelI(100) -the test conslusion is ab EMF AC to ground 49. aFvacLevelI(101) -the test conslusion is a EMF AC to ground 50. bFvacLevelI(102) -the test conslusion is b EMF AC to ground 51. abFvacLevelO(103) -the test conslusion is ab other dangerous AC to ground 52. aFvacLevelO(104) -the test conslusion is a other dangerous AC to ground 53. bFvacLevelO(105) -the test conslusion is b other dangerous AC to ground 54. abFvDcLevelH(106) -the test conslusion is ab dangerous DC to ground 55. aFvDcLevelH(107) -the test conslusion is a dangerous DC to ground 56. bFvDcLevelH(108) -the test conslusion is b dangerous DC to ground 57. abFvDcLevelI(109) -the test conslusion is ab EMF DC to ground 58. aFvDcLevelI(110) -the test conslusion is a EMF DC to ground 59. bFvDcLevelI(111) -the test conslusion is b EMF DC to ground 60. abFvDcLevelO(112) -the test conslusion is ab other dangerous DC to ground 61. aFvDcLevelO(113) -the test conslusion is a other dangerous DC to ground 62. bFvDcLevelO(114) -the test conslusion is b other dangerous DC to ground 63. fesIdPPA(115) -the test conslusion is ab PPA 64. fesIdPPAInv(116) -the test conslusion is ab reverse PPA 65. fesId2PPA(117) -the test conslusion is ab two PPA 66. fesId2PPAInv(118) -the test conslusion is ab two reverse PPA 67. etsiXdslSignature(119) -the test conslusion is ETSI XDSL Signature 68. fetIdEr(120) -the test conslusion is exist electronic ring terminal 69. abreak(121) -the test conslusion is a line break 70. bbreak(122) -the test conslusion is b line break 71. abreakInMDF(123) -the test conslusion is a line break InMDF 72. bbreakInMDF(124) -the test conslusion is b line break InMDF 73. abreakOutMDF(125) -the test conslusion is a line break OutMDF 74. bbreakOutMDF(126) -the test conslusion is b line break OutMDF 75. invalid(-1) -the test conclusion is invalid
Context
- MIB
- HUAWEI-COMMTEST-MIB
- OID
.1.3.6.1.4.1.2011.6.21.1.1.1.2.1.9- Type
- column
- Access
- readonly
- Status
- current
- Parent
- hwLoopLineTestOprEntry
- Table
- hwLoopLineTestOprTable
- Siblings
- 225
Syntax
Enumeration
Values & Constraints
Enumerated Values
-1 | invalid |
1 | normal |
2 | meetLine |
3 | aLineMix |
4 | bLineMix |
5 | doubleMix |
6 | aLineEarth |
7 | bLineEarth |
8 | doublelineearth |
9 | selfMix |
10 | abLine |
11 | aLineFree |
12 | bLineEarthFree |
13 | doubleLineEarthFree |
14 | abLineFree |
15 | killLine |
16 | noPutDownTele |
17 | unknow |
18 | selfMixinMDF |
19 | selfMixoutMDF |
20 | cutLineinMDF |
21 | cutLineoutMDF |
30 | dCvoltagePowerFeed |
31 | aCvoltageRinging |
32 | dCvoltageOffhook |
33 | dCvoltage |
34 | aCvoltage |
35 | abImpedance |
36 | baImpedance |
37 | agImpedance |
38 | bgImpedance |
39 | agACCurrent |
41 | bgACCurrent |
42 | abACCurrent |
43 | agDCCurrent |
44 | bgDCCurrent |
45 | abDCCurrent |
46 | loopCurrent |
47 | noise |
91 | abRFaultId |
92 | aRFaultId |
93 | bRFaultId |
94 | abLeakId |
95 | aLeakId |
96 | bLeakId |
97 | abFvacLevelH |
98 | aFvacLevelH |
99 | bFvacLevelH |
100 | abFvacLevelI |
101 | aFvacLevelI |
102 | bFvacLevelI |
103 | abFvacLevelO |
104 | aFvacLevelO |
105 | bFvacLevelO |
106 | abFvDcLevelH |
107 | aFvDcLevelH |
108 | bFvDcLevelH |
109 | abFvDcLevelI |
110 | aFvDcLevelI |
111 | bFvDcLevelI |
112 | abFvDcLevelO |
113 | aFvDcLevelO |
114 | bFvDcLevelO |
115 | fesIdPPA |
116 | fesIdPPAInv |
117 | fesId2PPA |
118 | fesId2PPAInv |
119 | etsiXdslSignature |
120 | fetIdEr |
121 | abreak |
122 | bbreak |
123 | abreakInMDF |
124 | bbreakInMDF |
125 | abreakOutMDF |
126 | bbreakOutMDF |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| hwLoopLineTestOprType MELT operation type
Options:
1. stop(1) -stop a MELT test
2. start(2) -start a MELT test
3. invalid(-1) -invalid value | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.1 |
| hwLoopLineTestACAG Indicates the A->ground AC voltage.
Unit: mV | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.10 |
| hwLoopLineTestRBGFlag Indicates whether the value of hwLoopLineTestRBG is valid.
Options:
1. valid(1) -the value of hwLoopLineTestRBG is valid
2. invalid(2) -the value of hwLoopLineTestRBG i… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.100 |
| hwLoopLineTestRABFlag Indicates whether the value of hwLoopLineTestRAB is valid.
Options:
1. valid(1) -the value of hwLoopLineTestRAB is valid
2. invalid(2) -the value of hwLoopLineTestRAB is… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.101 |
| hwLoopLineTestRABPoleFlag Indicates whether the value of hwLoopLineTestRABPole is valid.
Options:
1. valid(1) -the value of hwLoopLineTestRABPole is valid
2. invalid(2) -the value of hwLoopLineTe… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.102 |
| hwLoopLineTestRABResPoleFlag Indicates whether the value of hwLoopLineTestRABResPole is valid.
Options:
1. valid(1) -the value of hwLoopLineTestRABResPole is valid
2. invalid(2) -the value of hwLoo… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.103 |
| hwLoopLineTestCapAGFlag Indicates whether the value of hwLoopLineTestCapAG is valid.
Options:
1. valid(1) -the value of hwLoopLineTestCapAG is valid
2. invalid(2) -the value of hwLoopLineTestC… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.104 |
| hwLoopLineTestCapBGFlag Indicates whether the value of hwLoopLineTestCapBG is valid.
Options:
1. valid(1) -the value of hwLoopLineTestCapBG is valid
2. invalid(2) -the value of hwLoopLineTestC… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.105 |
| hwLoopLineTestCapABFlag Indicates whether the value of hwLoopLineTestCapAB is valid.
Options:
1. valid(1) -the value of hwLoopLineTestCapAB is valid
2. invalid(2) -the value of hwLoopLineTestC… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.106 |
| hwLoopLineTestRbattipFlag Indicates whether the value of hwLoopLineTestRbattip is valid.
Options:
1. valid(1) -the value of hwLoopLineTestRbattip is valid
2. invalid(2) -the value of hwLoopLineTestRbatt… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.107 |
| hwLoopLineTestRbatringFlag Indicates whether the value of hwLoopLineTestRbatring is valid.
Options:
1. valid(1) -the value of hwLoopLineTestRbatring is valid
2. invalid(2) -the value of hwLoopLineTestRba… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.108 |
| hwLoopLineTestRringFlag Indicates whether the value of hwLoopLineTestRring is valid.
Options:
1. valid(1) -the value of hwLoopLineTestRring is valid
2. invalid(2) -the value of hwLoopLineTestRring is … | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.109 |
| hwLoopLineTestACBG Indicates the B->ground AC voltage.
Unit: mV | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.11 |
| hwLoopLineTestCsigFlag Indicates whether the value of hwLoopLineTestCsig is valid.
Options:
1. valid(1) -the value of hwLoopLineTestCsig is valid
2. invalid(2) -the value of hwLoopLineTestCsig is inv… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.110 |
| hwLoopLineTestPPAResFlag Indicates whether the value of hwLoopLineTestPPARes is valid.
Options:
1. valid(1) -the value of hwLoopLineTestPPARes is valid
2. invalid(2) -the value of hwLoopLineTestPPARes … | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.111 |
| hwLoopLineTestVzenerFlag Indicates whether the value of hwLoopLineTestVzener is valid.
Options:
1. valid(1) -the value of hwLoopLineTestVzener is valid
2. invalid(2) -the value of hwLoopLineTestVzener … | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.112 |
| hwLoopLineTestRzenerFlag Indicates whether the value of hwLoopLineTestRzener is valid.
Options:
1. valid(1) -the value of hwLoopLineTestRzener is valid
2. invalid(2) -the value of hwLoopLineTestRzener … | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.113 |
| hwLoopLineTestSNMPRab Indicates the A to B resistance (insulation resistance).
Unit: ohm | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.114 |
| hwLoopLineTestSNMPRabFlag Indicates whether the value of hwLoopLineTestSNMPRab is valid.
Options:
1. valid(1) -the value of hwLoopLineTestSNMPRab is valid
2. invalid(2) -the value of hwLoopLineTestSNMP… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.115 |
| hwLoopLineTestSNMPRba Indicates the B to A resistance (insulation resistance).
Unit: ohm | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.116 |
| hwLoopLineTestSNMPRbaFlag Indicates whether the value of hwLoopLineTestSNMPRba is valid.
Options:
1. valid(1) -the value of hwLoopLineTestSNMPRba is valid
2. invalid(2) -the value of hwLoopLineTestSNMPR… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.117 |
| hwLoopLineTestPPAResultFlag Indicates whether the value of hwLoopLineTestPPA is valid.
Options:
1. valid(1) -the value of hwLoopLineTestPPA is valid
2. invalid(2) -the value of hwLoopLineTestPPA is invalid | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.118 |
| hwLoopLineTestUtgAcFreqFlag Indicates whether the value of hwLoopLineTestUtgAcFreq is valid.
Options:
1. valid(1) -the value of hwLoopLineTestUtgAcFreq is valid
2. invalid(2) -the value of hwLoopLi… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.119 |
| hwLoopLineTestACAB Indicates the A->B AC voltage.
Unit: mV | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.12 |
| hwLoopLineTestUrgAcFreqFlag Indicates whether the value of hwLoopLineTestUrgAcFreq is valid.
Options:
1. valid(1) -the value of hwLoopLineTestUrgAcFreq is valid
2. invalid(2) -the value of hwLoopLi… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.120 |
| hwLoopLineTestUtrAcFreqFlag Indicates whether the value of hwLoopLineTestUtrAcFreq is valid.
Options:
1. valid(1) -the value of hwLoopLineTestUtrAcFreq is valid
2. invalid(2) -the value of hwLoopLi… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.121 |
| hwLoopLineTestItipAcFlag Indicates whether the value of hwLoopLineTestItipAc is valid.
Options:
1. valid(1) -the value of hwLoopLineTestItipAc is valid
2. invalid(2) -the value of hwLoopLineTes… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.122 |
| hwLoopLineTestIringAcFlag Indicates whether the value of hwLoopLineTestIringAc is valid.
Options:
1. valid(1) -the value of hwLoopLineTestIringAc is valid
2. invalid(2) -the value of hwLoopLineT… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.123 |
| hwLoopLineTestItipDcFlag Indicates whether the value of hwLoopLineTestItipDc is valid.
Options:
1. valid(1) -the value of hwLoopLineTestItipDc is valid
2. invalid(2) -the value of hwLoopLineTes… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.124 |
| hwLoopLineTestIringDcFlag Indicates whether the value of hwLoopLineTestIringDc is valid.
Options:
1. valid(1) -the value of hwLoopLineTestIringDc is valid
2. invalid(2) -the value of hwLoopLineT… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.125 |
| hwLoopLineTestGtgFlag Indicates whether the value of hwLoopLineTestGtg is valid.
Options:
1. valid(1) -the value of hwLoopLineTestGtg is valid
2. invalid(2) -the value of hwLoopLineTestGtg is… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.126 |
| hwLoopLineTestBtgFlag Indicates whether the value of hwLoopLineTestBtg is valid.
Options:
1. valid(1) -the value of hwLoopLineTestBtg is valid
2. invalid(2) -the value of hwLoopLineTestBtg i… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.127 |
| hwLoopLineTestGrgFlag Indicates whether the value of hwLoopLineTestGrg is valid.
Options:
1. valid(1) -the value of hwLoopLineTestGrg is valid
2. invalid(2) -the value of hwLoopLineTestGrg is… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.128 |
| hwLoopLineTestBrgFlag Indicates whether the value of hwLoopLineTestBrg is valid.
Options:
1. valid(1) -the value of hwLoopLineTestBrg is valid
2. invalid(2) -the value of hwLoopLineTestBrg i… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.129 |
| hwLoopLineTestDCAG Indicates the A->ground DC voltage.
Unit: mV | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.13 |
| hwLoopLineTestGtrFlag Indicates whether the value of hwLoopLineTestGtr is valid.
Options:
1. valid(1) -the value of hwLoopLineTestGtr is valid
2. invalid(2) -the value of hwLoopLineTestGtr i… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.130 |
| hwLoopLineTestBtrFlag Indicates whether the value of hwLoopLineTestBtr is valid.
Options:
1. valid(1) -the value of hwLoopLineTestBtr is valid
2. invalid(2) -the value of hwLoopLineTestBtr is invalid | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.131 |
| hwLoopLineTestSIGNFlag Indicates whether the value of hwLoopLineTestSIGN is valid.
Options:
1. valid(1) -the value of hwLoopLineTestSIGN is valid
2. invalid(2) -the value of hwLoopLineTestSIGN is inv… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.132 |
| hwLoopLineTestACFEMFlag Indicates whether the value of hwLoopLineTestACFEM is valid.
Options:
1. valid(1) -the value of hwLoopLineTestACFEM is valid
2. invalid(2) -the value of hwLoopLineTestACFEM is i… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.133 |
| hwLoopLineTestDCFEMFlag Indicates whether the value of hwLoopLineTestDCFEM is valid.
Options:
1. valid(1) -the value of hwLoopLineTestDCFEM is valid
2. invalid(2) -the value of hwLoopLineTestDCFEM is i… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.134 |
| hwLoopLineTestONHKFlag Indicates whether the value of hwLoopLineTestONHK is valid.
Options:
1. valid(1) -the value of hwLoopLineTestONHK is valid
2. invalid(2) -the value of hwLoopLineTestONHK is inv… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.135 |
| hwLoopLineTestOPENFlag Indicates whether the value of hwLoopLineTestOPEN is valid.
Options:
1. valid(1) -the value of hwLoopLineTestOPEN is valid
2. invalid(2) -the value of hwLoopLineTestOPEN is inv… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.136 |
| hwLoopLineTestSHORTFlag Indicates whether the value of hwLoopLineTestSHORT is valid.
Options:
1. valid(1) -the value of hwLoopLineTestSHORT is valid
2. invalid(2) -the value of hwLoopLineTestSHORT is … | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.137 |
| hwLoopLineTestROHFlag Indicates whether the value of hwLoopLineTestROH is valid.
Options:
1. valid(1) -the value of hwLoopLineTestROH is valid
2. invalid(2) -the value of hwLoopLineTestROH is invalid | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.138 |
| hwLoopLineTestUtgDcUpFlag Indicates whether the value of hwLoopLineTestUtgDcUp is valid.
Options:
1. valid(1) -the value of hwLoopLineTestUtgDcUp is valid
2. invalid(2) -the value of hwLoopLineTestUtgDc… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.139 |
| hwLoopLineTestDCBG Indicates the B->ground DC voltage.
Unit: mV | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.14 |
| hwLoopLineTestUtgDcDownFlag Indicates whether the value of hwLoopLineTestUtgDcDown is valid.
Options:
1. valid(1) -the value of hwLoopLineTestUtgDcDown is valid
2. invalid(2) -the value of hwLoopLineTestU… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.140 |
| hwLoopLineTestUrgDcUpFlag Indicates whether the value of hwLoopLineTestUrgDcUp is valid.
Options:
1. valid(1) -the value of hwLoopLineTestUrgDcUp is valid
2. invalid(2) -the value of hwLoopLineTestUrgDcU… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.141 |
| hwLoopLineTestUrgDcDownFlag Indicates whether the value of hwLoopLineTestUrgDcDown is valid.
Options:
1. valid(1) -the value of hwLoopLineTestUrgDcDown is valid
2. invalid(2) -the value of hwLoopLineTestUr… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.142 |
| hwLoopLineTestUtrPosFlag Indicates whether the value of hwLoopLineTestUtrPos is valid.
Options:
1. valid(1) -the value of hwLoopLineTestUtrPos is valid
2. invalid(2) -the value of hwLoopLineTestUtrPos … | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.143 |
| hwLoopLineTestUtrNegFlag Indicates whether the value of hwLoopLineTestUtrNeg is valid.
Options:
1. valid(1) -the value of hwLoopLineTestUtrNeg is valid
2. invalid(2) -the value of hwLoopLineTestUtrNeg … | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.144 |
| hwLoopLineTestItgDcUpFlag Indicates whether the value of hwLoopLineTestItgDcUp is valid.
Options:
1. valid(1) -the value of hwLoopLineTestItgDcUp is valid
2. invalid(2) -the value of hwLoopLineTestItgDc… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.145 |
| hwLoopLineTestItgDcDownFlag Indicates whether the value of hwLoopLineTestItgDcDown is valid.
Options:
1. valid(1) -the value of hwLoopLineTestItgDcDown is valid
2. invalid(2) -the value of hwLoopLineTestI… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.146 |
| hwLoopLineTestIrgDcUpFlag Indicates whether the value of hwLoopLineTestIrgDcUp is valid.
Options:
1. valid(1) -the value of hwLoopLineTestIrgDcUp is valid
2. invalid(2) -the value of hwLoopLineTestIrgDc… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.147 |
| hwLoopLineTestIrgDcDownFlag Indicates whether the value of hwLoopLineTestIrgDcDown is valid.
Options:
1. valid(1) -the value of hwLoopLineTestIrgDcDown is valid
2. invalid(2) -the value of hwLoopLineTestIr… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.148 |
| hwLoopLineTestItrPosFlag Indicates whether the value of hwLoopLineTestItrPos is valid.
Options:
1. valid(1) -the value of hwLoopLineTestItrPos is valid
2. invalid(2) -the value of hwLoopLineTestItrPos … | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.149 |
| hwLoopLineTestDCAB Indicates the A->B DC voltage.
Unit: mV | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.15 |
| hwLoopLineTestItrNegFlag Indicates whether the value of hwLoopLineTestItrNeg is valid.
Options:
1. valid(1) -the value of hwLoopLineTestItrNeg is valid
2. invalid(2) -the value of hwLoopLineTestItrNeg i… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.150 |
| hwLoopLineTestRingerFlag Indicates whether the value of hwLoopLineTestRinger is valid.
Options:
1. valid(1) -the value of hwLoopLineTestRinger is valid
2. invalid(2) -the value of hwLoopLineTestRinger i… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.151 |
| hwLoopLineTestLRFlag Indicates whether the value of hwLoopLineTestLR is valid.
Options:
1. valid(1) -the value of hwLoopLineTestLR is valid
2. invalid(2) -the value of hwLoopLineTestLR is in… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.152 |
| hwLoopLineTestDcCurrent Indicates whether DcCurrent exists on the line under test.
Options:
1. notest(1) -DcCurrent does not exist on the line under test
2. test(2) -DcCurrent exists on the line u… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.153 |
| hwLoopLineTestAcCurrent Indicates whether AcCurrent exists on the line under test.
Options:
1. notest(1) -AcCurrent does not exist on the line under test
2. test(2) -AcCurrent exists on the line u… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.154 |
| hwLoopLineTestConductance Indicates whether conductance exists on the line under test.
Options:
1. notest(1) -Conductance does not exist on the line under test
2. test(2) -Conductance exists on the … | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.155 |
| hwLoopLineTestSusceptance Indicates whether susceptance exists on the line under test.
Options:
1. notest(1) -Susceptance does not exist on the line under test
2. test(2) -Susceptance exists on the … | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.156 |
| hwLoopLineTestAcfrequencyA Indicates status of Acfrequency in line A.
Options:
1. sixteenDotSix(1) -line A has ACFrequency 16.6
2. twentyFive(2) -line A has ACFrequency 25
3. fifty(3) -line A… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.157 |
| hwLoopLineTestAcfrequencyB Indicates status of Acfrequency in line A.
Options:
1. sixteenDotSix(1) -line A has ACFrequency 16.6
2. twentyFive(2) -line A has ACFrequency 25
3. fifty(3) -line A… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.158 |
| hwLoopLineTestCapABH Indicates the A->B capacitance.
Unit: nF | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.159 |
| hwLoopLineTestRAG Indicates the A->ground insulation resistance.
Unit: ohm | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.16 |
| hwLoopLineTestCapABHFlag Indicates whether the value of hwLoopLineTestCapABH is valid.
Options:
1. valid(1) -the value of hwLoopLineTestCapABH is valid
2. invalid(2) -the value of hwLoopLineTest… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.160 |
| hwLoopLineTestGtrH Indicates the A->B conductance.
Unit: nS | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.161 |
| hwLoopLineTestGtrHFlag Indicates whether the value of hwLoopLineTestGtrH is valid.
Options:
1. valid(1) -the value of hwLoopLineTestGtrH is valid
2. invalid(2) -the value of hwLoopLineTestGtrH… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.162 |
| hwLoopLineTestBtrH Indicates the A->B susceptance.
Unit: nS | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.163 |
| hwLoopLineTestBtrHFlag Indicates whether the value of hwLoopLineTestBtrH is valid.
Options:
1. valid(1) -the value of hwLoopLineTestBtrH is valid
2. invalid(2) -the value of hwLoopLineTestBtrH… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.164 |
| hwLoopLineTestABDcCurrent Indicates the A->B Dc current.
Unit: uA | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.165 |
| hwLoopLineTestABDcCurrentFlag Indicates whether the value of hwLoopLineTestABDcCurrent is valid.
Options:
1. valid(1) -the value of hwLoopLineTestABDcCurrent is valid
2. invalid(2) -the value of hwLo… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.166 |
| hwLoopLineTestBADcCurrent Indicates the B->A Dc current.
Unit: uA | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.167 |
| hwLoopLineTestBADcCurrentFlag Indicates whether the value of hwLoopLineTestBADcCurrent is valid.
Options:
1. valid(1) -the value of hwLoopLineTestBADcCurrent is valid
2. invalid(2) -the value of hwLo… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.168 |
| hwLoopLineTestABAcCurrent Indicates the A->B Ac current.
Unit: uArms | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.169 |
| hwLoopLineTestRBG Indicates the B->ground insulation resistance.
Unit: ohm | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.17 |
| hwLoopLineTestABAcCurrentFlag Indicates whether the value of hwLoopLineTestABAcCurrent is valid.
Options:
1. valid(1) -the value of hwLoopLineTestABAcCurrent is valid
2. invalid(2) -the value of hwLo… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.170 |
| hwLoopLineTestBAAcCurrent Indicates the B->A Ac current.
Unit: uArms | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.171 |
| hwLoopLineTestBAAcCurrentFlag Indicates whether the value of hwLoopLineTestBAAcCurrent is valid.
Options:
1. valid(1) -the value of hwLoopLineTestBAAcCurrent is valid
2. invalid(2) -the value of hwLo… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.172 |
| hwLoopLineTestCSfrequencyForTest Indicates the frequency for test capacitance and conductance.
Unit: Hz | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.173 |
| hwLoopLineTestCSfrequencyForTestFlag Indicates whether the value of hwLoopLineTestCSfrequencyForTest is valid.
Options:
1. valid(1) -the value of hwLoopLineTestCSfrequencyForTest is valid
2. invalid(2) -the… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.174 |
| hwLoopLineTestImpedanceForTest Indicates the resistance inputed in test abnormal voltage.
Unit: ohm | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.175 |
| hwLoopLineTestImpedanceForTestFlag Indicates whether the value of hwLoopLineTestImpedanceForTest is valid.
Options:
1. valid(1) -the value of hwLoopLineTestImpedanceForTest is valid
2. invalid(2) -the val… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.176 |
| hwLoopLineTestMaxVForSignature Indicates the maximum voltage for signature.
Unit: mV | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.177 |
| hwLoopLineTestMaxVForSignatureFlag Indicates whether the value of hwLoopLineTestMaxVForSignature is valid.
Options:
1. valid(1) -the value of hwLoopLineTestMaxVForSignature is valid
2. invalid(2) -the val… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.178 |
| hwLoopLineTestAGMaxVForTest Indicates the A->ground max voltage in testing.
Unit: mV | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.179 |
| hwLoopLineTestRAB Indicates the A->B insulation resistance.
Unit: ohm | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.18 |
| hwLoopLineTestAGMaxVForTestFlag Indicates whether the value of hwLoopLineTestAGMaxVForTest is valid.
Options:
1. valid(1) -the value of hwLoopLineTestAGMaxVForTest is valid
2. invalid(2) -the value of … | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.180 |
| hwLoopLineTestAGMinVForTest Indicates the A->ground min voltage in testing.
Unit: mV | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.181 |
| hwLoopLineTestAGMinVForTestFlag Indicates whether the value of hwLoopLineTestAGMinVForTest is valid.
Options:
1. valid(1) -the value of hwLoopLineTestAGMinVForTest is valid
2. invalid(2) -the value of … | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.182 |
| hwLoopLineTestBGMaxVForTest Indicates the B->ground max voltage in testing.
Unit: mV | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.183 |
| hwLoopLineTestBGMaxVForTestFlag Indicates whether the value of hwLoopLineTestBGMaxVForTest is valid.
Options:
1. valid(1) -the value of hwLoopLineTestBGMaxVForTest is valid
2. invalid(2) -the value of … | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.184 |
| hwLoopLineTestBGMinVForTest Indicates the B->ground min voltage in testing.
Unit: mV | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.185 |
| hwLoopLineTestBGMinVForTestFlag Indicates whether the value of hwLoopLineTestBGMinVForTest is valid.
Options:
1. valid(1) -the value of hwLoopLineTestBGMinVForTest is valid
2. invalid(2) -the value of … | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.186 |
| hwLoopLineTestABMaxVForTest Indicates the A->B max voltage in testing.
Unit: mV | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.187 |
| hwLoopLineTestABMaxVForTestFlag Indicates whether the value of hwLoopLineTestABMaxVForTest is valid.
Options:
1. valid(1) -the value of hwLoopLineTestABMaxVForTest is valid
2. invalid(2) -the value of … | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.188 |
| hwLoopLineTestABMinVForTest Indicates the A->ground min voltage in testing.
Unit: mV | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.189 |
| hwLoopLineTestCapAG Indicates the A->ground capacitance.
Unit: nF | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.19 |
| hwLoopLineTestABMinVForTestFlag Indicates whether the value of hwLoopLineTestABMinVForTest is valid.
Options:
1. valid(1) -the value of hwLoopLineTestABMinVForTest is valid
2. invalid(2) -the value of … | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.190 |
| hwLoopLineTestAGMaxCForTest Indicates the A->ground max current.
Unit: uA | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.191 |
| hwLoopLineTestAGMaxCForTestFlag Indicates whether the value of hwLoopLineTestAGMaxCForTest is valid.
Options:
1. valid(1) -the value of hwLoopLineTestAGMaxCForTest is valid
2. invalid(2) -the value of … | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.192 |
| hwLoopLineTestAGMinCForTest Indicates the A->ground min current.
Unit: uA | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.193 |
| hwLoopLineTestAGMinCForTestFlag Indicates whether the value of hwLoopLineTestAGMinCForTest is valid.
Options:
1. valid(1) -the value of hwLoopLineTestAGMinCForTest is valid
2. invalid(2) -the value of … | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.194 |
| hwLoopLineTestBGMaxCForTest Indicates the B->ground max current.
Unit: uA | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.195 |
| hwLoopLineTestBGMaxCForTestFlag Indicates whether the value of hwLoopLineTestBGMaxCForTest is valid.
Options:
1. valid(1) -the value of hwLoopLineTestBGMaxCForTest is valid
2. invalid(2) -the value of … | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.196 |
| hwLoopLineTestBGMinCForTest Indicates the B->ground min current.
Unit: uA | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.197 |
| hwLoopLineTestBGMinCForTestFlag Indicates whether the value of hwLoopLineTestBGMinCForTest is valid.
Options:
1. valid(1) -the value of hwLoopLineTestBGMinCForTest is valid
2. invalid(2) -the value of … | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.198 |
| hwLoopLineTestABMaxCForTest Indicates the A->B max current
Unit: uA | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.199 |
| hwLoopLineTestVoltage Indicates whether a voltage exists on the line under test.
Options:
1. notest(1) -the voltage does not exist on the line under test
2. test(2) -the voltage exists on the li… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.2 |
| hwLoopLineTestCapBG Indicates the B->ground capacitance.
Unit: nF | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.20 |
| hwLoopLineTestABMaxCForTestFlag Indicates whether the value of hwLoopLineTestABMaxCForTest is valid.
Options:
1. valid(1) -the value of hwLoopLineTestABMaxCForTest is valid
2. invalid(2) -the value of … | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.200 |
| hwLoopLineTestABMaxNegCForTest Indicates the A->ground min current
Unit: uA | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.201 |
| hwLoopLineTestABMaxNegCForTestFlag Indicates whether the value of hwLoopLineTestABMaxNegCForTest is valid.
Options:
1. valid(1) -the value of hwLoopLineTestABMaxNegCForTest is valid
2. invalid(2) -the val… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.202 |
| hwLoopLineTestLineALength Indicates length of line A
Unit: m | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.203 |
| hwLoopLineTestLineBLength Indicates length of line B
Unit: m | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.204 |
| hwLoopLineTestTermimalConcusion Indicates Termimal Concusion
Options:
1. noPhone(1) -the TermimalConcusion is not connect Phone
2. offHook(2) -the TermimalConcusion is… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.205 |
| hwLoopLineTestMoreDataFlag Indicates is there more data
Options:
1. more(1) -Indicates there is more data needs report,but needs a SNMP-GET oper. to get other data.
2. invalid(-1) … | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.206 |
| hwLoopLineTestCtrLV Aggregate tip-ring capacitance: CtrLV = Cco + Ctr + Cring, measured by means of low voltage ramps,
such that it does NOT include the capacitance Csig whenever the ETSI Signature t… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.207 |
| hwLoopLineTestCtrLVFlag Indicates whether the value of hwLoopLineTestCtrLV is valid.
Options:
1. valid(1) -the value of hwLoopLineTestCtrLV is valid
2. invalid(2) -the value of hwLoopLineTestC… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.208 |
| hwLoopLineTestCtrHV Aggregate tip-ring capacitance: CtrHV = Cco + Ctr + Cring + Csig, measured by means of high voltage ramps.
It includes the capacitance Csig of an ETSI Signature whenever connected… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.209 |
| hwLoopLineTestCapAB Indicates the A->B capacitance.
Unit: nF | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.21 |
| hwLoopLineTestCtrHVFlag Indicates whether the value of hwLoopLineTestCtrHV is valid.
Options:
1. valid(1) -the value of hwLoopLineTestCtrHV is valid
2. invalid(2) -the value of hwLoopLineTestC… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.210 |
| hwLoopLineTestCtrAc Aggregate tip-ring capacitance: CtrAc = Cco + Ctr + Cring, measured by means of a low amplitude
AC signal (either 25 Hz or 275 Hz). It does NOT include Csig.
Unit: nF | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.211 |
| hwLoopLineTestCtrAcFlag Indicates whether the value of hwLoopLineTestCtrAc is valid.
Options:
1. valid(1) -the value of hwLoopLineTestCtrAc is valid
2. invalid(2) -the value of hwLoopLineTestC… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.212 |
| hwLoopLineTestRtgSer Resistance in series with Ctg, measured at the selected AC frequency (either 25 Hz or 275 Hz)
by means of a low amplitude AC signal.
Unit: ohm | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.213 |
| hwLoopLineTestRtgSerFlag Indicates whether the value of hwLoopLineTestRtgSer is valid.
Options:
1. valid(1) -the value of hwLoopLineTestRtgSer is valid
2. invalid(2) -the value of hwLoopLineTes… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.214 |
| hwLoopLineTestRrgSer Resistance in series with Crg, measured at the selected AC frequency (either 25 Hz or 275 Hz)
by means of a low amplitude AC signal.
Unit: ohm | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.215 |
| hwLoopLineTestRrgSerFlag Indicates whether the value of hwLoopLineTestRrgSer is valid.
Options:
1. valid(1) -the value of hwLoopLineTestRrgSer is valid
2. invalid(2) -the value of hwLoopLineTes… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.216 |
| hwLoopLineTestRtrSer Resistance in series with Ctring, measured at the selected AC frequency (either 25 Hz or 275 Hz)
by means of a low amplitude AC signal.
Unit: ohm | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.217 |
| hwLoopLineTestRtrSerFlag Indicates whether the value of hwLoopLineTestRtrSer is valid.
Options:
1. valid(1) -the value of hwLoopLineTestRtrSer is valid
2. invalid(2) -the value of hwLoopLineTes… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.218 |
| hwLoopLineTestUtgAcAdmit Amplitude of the AC signal (either 25 Hz or 275 Hz) applied to the tipground admittance Ytg = Gtg + i * Btg.
Unit: V | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.219 |
| hwLoopLineTestLR Indicates the loop resistance.
Unit: ohm | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.22 |
| hwLoopLineTestUtgAcAdmitFlag Indicates whether the value of hwLoopLineTestUtgAcAdmit is valid.
Options:
1. valid(1) -the value of hwLoopLineTestUtgAcAdmit is valid
2. invalid(2) -the value of hwLoo… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.220 |
| hwLoopLineTestUrgAcAdmit Amplitude of the AC signal (either 25 Hz or 275 Hz) applied to the ringground admittance Yrg = Grg + i * Brg.
Unit: V | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.221 |
| hwLoopLineTestUrgAcAdmitFlag Indicates whether the value of hwLoopLineTestUrgAcAdmit is valid.
Options:
1. valid(1) -the value of hwLoopLineTestUrgAcAdmit is valid
2. invalid(2) -the value of hwLoo… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.222 |
| hwLoopLineTestUtrAcAdmit Amplitude of the AC signal (either 25 Hz or 275 Hz) applied to the tip-ring admittance Ytr = Gtr + i * Btr.
Unit: V | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.223 |
| hwLoopLineTestUtrAcAdmitFlag Indicates whether the value of hwLoopLineTestUtrAcAdmit is valid.
Options:
1. valid(1) -the value of hwLoopLineTestUtrAcAdmit is valid
2. invalid(2) -the value of hwLoo… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.224 |
| hwLoopLineTestCapterminal A capacitive termination of the access line shall be identified by the capacitance measurement and the associated evaluation.
The following average value for the capacitance Cabk … | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.225 |
| hwLoopLineTestCapterminalFlag Indicates whether the value of hwLoopLineTestCapterminal is valid.
Options:
1. valid(1) -the value of hwLoopLineTestCapterminal is valid
2. invalid(2) -the value of hwL… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.226 |
| hwLoopLineTestRABResPole Indicates the A->B polarity reversal resistance.
Unit: ohm | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.23 |
| hwLoopLineTestMSocket Indicates the M-socket connection.
Options:
1. notconnected(1) -the M-socket is not connected
2. connected(2) -the M-socket is connected
3. aBReversed(3) -the wire A and wi… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.24 |
| hwLoopLineTestBtssPowerProcFlag Loop line test-BTSS line with power processing.
Options:
1. noTest(1) -not test
2. test(2) -test
3. invalid(-1) -invalid value | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.25 |
| hwLoopLineTestImpedance Loop line test-impedance.
Options:
1. notest(1) -not test
2. test(2) -test | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.26 |
| hwLoopLineTestImpedanceAB A->B impedance (unit: ohm) | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.27 |
| hwLoopLineTestImpedanceBA B->A impedance (unit: ohm) | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.28 |
| hwLoopLineTestImpedanceAG A->ground impedance (unit: ohm) | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.29 |
| hwLoopLineTestResistance Indicates whether resistance exists on the line under test.
Options:
1. notest(1) -resistance does not exist on the line under test
2. test(2) -resistance exists on the lin… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.3 |
| hwLoopLineTestImpedanceBG B->ground impedance (unit: ohm) | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.30 |
| hwLoopLineTestCurrent Loop line test-current.
Options:
1. notest(1) -not test
2. test(2) -test | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.31 |
| hwLoopLineTestACCurrentAG A->ground AC current (unit: mA) | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.32 |
| hwLoopLineTestACCurrentBG B->ground AC current (unit: mA) | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.33 |
| hwLoopLineTestACCurrentAB AB AC current (unit: mA) | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.34 |
| hwLoopLineTestDCCurrentAG A->ground DC current (unit: mA) | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.35 |
| hwLoopLineTestDCCurrentBG B->ground DC current (unit: mA) | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.36 |
| hwLoopLineTestDCCurrentAB AB DC current (unit: mA) | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.37 |
| hwLoopLineTestLoopCurrent Loop line test-loop current.
Options:
1. notest(1) -not test
2. test(2) -test | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.38 |
| hwLoopLineTestLC Loop current (unit: uA) | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.39 |
| hwLoopLineTestCapacitance Indicates whether capacitance exists on the line under test.
Options:
1. notest(1) -capacitance does not exist on the line under test
2. test(2) -capacitance exists on the … | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.4 |
| hwLoopLineTestNoise Loop line test-noise.
Options:
1. notest(1) -not test
2. test(2) -test | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.40 |
| hwLoopLineTestN Noise (unit: dBm) | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.41 |
| hwLoopLineTestPPA Indicates whether PPA exists on the line under test.
Options:
1. notest(1) -PPA does not exist on the line under test
2. test(2) -PPA exists on the line under test
3. inval… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.42 |
| hwLoopLineTestPPAResult Indicates whether the PPA exists.
Options:
1. noexist(1) -PPA does not exist
2. exist(2) -PPA exists
3. inverseexist(3) -PPA inverse exists
4. invalid(-1) -i… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.43 |
| hwLoopLineTestDeferredTime Indicates the deferred time.
Unit: minute
This leaf is valid only when the value of hwLoopLineTestBusyProcFlag is DeferredTest(4).
Default: 30 | column | Integer32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.44 |
| hwLoopLineTestTimeoutProc Indicates the timeout processing.
Options:
1. notest(1) -if the deferred time times out and the port is still busy
the test will be canceled
2. test(2) -i… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.45 |
| hwLoopLineTestReverse Reverse flag (0:normal test 1:reverse test) | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.46 |
| hwLoopLineTestUtgAcFreq Frequency of foreign AC voltage source coupled to tip via Zbat_tip impedance.
Unit: Hz | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.47 |
| hwLoopLineTestUrgAcFreq Frequency of foreign AC voltage source coupled to ring via Zbat_ring impedance.
Unit:Hz | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.48 |
| hwLoopLineTestUtrAcFreq Frequency of foreign AC voltage source coupled to tip-ring via Zbat_tipring impedance.
Unit:Hz | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.49 |
| hwLoopLineTestLoopResistance Indicates whether loop resistance exists on the line under test.
Options:
1. notest(1) -loop resistance does not exist on the line under test
2. test(2) -loop resistance ex… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.5 |
| hwLoopLineTestItipAc AC foreign current on the tip wire.
Unit:uA | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.50 |
| hwLoopLineTestIringAc AC foreign current on the ring wire.
Unit:uA | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.51 |
| hwLoopLineTestItipDc DC foreign current on the tip wire.
Unit:uA | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.52 |
| hwLoopLineTestIringDc DC foreign current on the ring wire.
Unit:uA | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.53 |
| hwLoopLineTestRbattip In presence of a foreign voltage, the equivalent coupling resistance of wire A.
Unit:ohm | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.54 |
| hwLoopLineTestRbatring In presence of a foreign voltage, the equivalent coupling resistance of wire B.
Unit:ohm | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.55 |
| hwLoopLineTestRring Resistance in series with the ring capacitance, for example
when a ringer load or a passive R-C signature terminates the loop.
It also includes the cable resistance R line but it… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.56 |
| hwLoopLineTestCsig Capacitance of an xDSL signal.
Unit: nF | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.57 |
| hwLoopLineTestVzener Zener diode threshold in the case of an off-hook phone.
Unit: mV | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.58 |
| hwLoopLineTestRzener DC tip-ring resistance measured in the case of an off-hook phone.
Unit: ohm | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.59 |
| hwLoopLineTestPoleResistance Indicates whether pole resistance exists on the line under test.
Options:
1. notest(1) -Pole resistance does not exist on the line under test
2. test(2) -Pole resistance ex… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.6 |
| hwLoopLineTestGtg Aggregate a->ground conductance.
Unit: nS | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.60 |
| hwLoopLineTestBtg Aggregate a->ground susceptance.
Unit: nS | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.61 |
| hwLoopLineTestGrg Aggregate b->ground conductance.
Unit: nS | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.62 |
| hwLoopLineTestBrg Aggregate b->ground susceptance.
Unit: nS | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.63 |
| hwLoopLineTestGtr Aggregate a->b conductance.
Unit: nS | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.64 |
| hwLoopLineTestBtr Aggregate a->b susceptance.
Unit: nS | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.65 |
| hwLoopLineTestSIGN Indicates the ETSI xDSL Signature is detected or not. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.66 |
| hwLoopLineTestACFEM Indicates the presence of an AC foreign voltage above the threshold defined by ACFEMmin.
By reading the results of the foreign voltage test, it is possible to determine
whether … | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.67 |
| hwLoopLineTestDCFEM Indicates the presence of a DC foreign voltage above the threshold defined
by DCFEMmin. By reading the results of the foreign voltage test,
it is possible to determine whether t… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.68 |
| hwLoopLineTestONHK Indicates the presens of a phone in the on-hook state. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.69 |
| hwLoopLineTestBusyProcFlag Identify whether to start a test when the line is busy. The system will excecute a corresponding
operation according to the configuration that a user specifies, for example, to c… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.7 |
| hwLoopLineTestOPEN Indicates a->b resistance exceeds the threshold. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.70 |
| hwLoopLineTestSHORT Indicates that the insulation resistance is small. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.71 |
| hwLoopLineTestROH Indicates a phone in the off-hook state. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.72 |
| hwLoopLineTestUtgDcUp Indicates the a->ground highest measurement DC voltage.
Unit: mV | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.73 |
| hwLoopLineTestUtgDcDown Indicates the a->ground lowest measurement DC voltage.
Unit: mV | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.74 |
| hwLoopLineTestUrgDcUp Indicates the b->ground highest measurement DC voltage.
Unit: mV | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.75 |
| hwLoopLineTestUrgDcDown Indicates the b->ground lowest measurement DC voltage.
Unit: mV | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.76 |
| hwLoopLineTestUtrPos Indicates the a->b positive measurement DC voltage.
Unit: mV | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.77 |
| hwLoopLineTestUtrNeg Indicates the b->a measurement DC voltage.
Unit: mV | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.78 |
| hwLoopLineTestItgDcUp Indicates the current mapping the A-wire highest voltage for test.
Unit: uA | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.79 |
| hwLoopLineTestStatus Indicates the result of MELT test.
Options:
1. normal(1) -the MELT test is successful
2. testFail(2) -the MELT test fails
3. portBusy(3) -the MELT te… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.8 |
| hwLoopLineTestItgDcDown Indicates the current mapping the A-wire lowest voltage for test.
Unit: uA | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.80 |
| hwLoopLineTestIrgDcUp Indicates the current mapping the B-wire highest voltage for test.
Unit: uA | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.81 |
| hwLoopLineTestIrgDcDown Indicates the current mapping the B-wire lowest voltage for test.
Unit: uA | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.82 |
| hwLoopLineTestItrPos Indicates the current mapping the A->B positive voltage for test.
Unit: uA | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.83 |
| hwLoopLineTestItrNeg Indicates the current mapping the A->B negative voltage for test.
Unit: uA | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.84 |
| hwLoopLineTestRinger Indicates the detected ringer. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.85 |
| hwLoopLineTestPPARes Indicates the resistance of PPA.
Unit: ohm | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.86 |
| hwLoopLineTestStartTime Indicates the start time and date of the MELT test. | column | SNMPv2-TCDateAndTime | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.87 |
| hwLoopLineTestEndTime Indicates the end time and date of the MELT test. | column | SNMPv2-TCDateAndTime | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.88 |
| hwLoopLineTestOprMeasuredFreq Indicates the measured frequency for complex impedance.
Options:
1. frequency25Hz(0) -25 Hz
2. frequency275Hz(1) -275 Hz
3. invalid(-1) -invalid value
Default: frequency2… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.89 |
| hwLoopLineTestIfIndex Port IfIndex. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.90 |
| hwLoopLineTestRequestID Request ID.
The value is the fourth parameter in the trap message. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.91 |
| hwLoopLineTestRABPole Indicates the A->B polarity resistance.
Unit: ohm | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.92 |
| hwLoopLineTestACAGFlag Indicates whether the value of hwLoopLineTestACAG is valid.
Options:
1. valid(1) -the value of hwLoopLineTestACAG is valid
2. invalid(2) -the value of hwLoopLineTestACA… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.93 |
| hwLoopLineTestACBGFlag Indicates whether the value of hwLoopLineTestACBG is valid.
Options:
1. valid(1) -the value of hwLoopLineTestACBG is valid
2. invalid(2) -the value of hwLoopLineTestACBG is inv… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.94 |
| hwLoopLineTestACABFlag Indicates whether the value of hwLoopLineTestACAB is valid.
Options:
1. valid(1) -the value of hwLoopLineTestACAB is valid
2. invalid(2) -the value of hwLoopLineTestACA… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.95 |
| hwLoopLineTestDCAGFlag Indicates whether the value of hwLoopLineTestDCAG is valid.
Options:
1. valid(1) -the value of hwLoopLineTestDCAG is valid
2. invalid(2) -the value of hwLoopLineTestDCAG… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.96 |
| hwLoopLineTestDCBGFlag Indicates whether the value of hwLoopLineTestDCBG is valid.
Options:
1. valid(1) -the value of hwLoopLineTestDCBG is valid
2. invalid(2) -the value of hwLoopLineTestDCB… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.97 |
| hwLoopLineTestDCABFlag Indicates whether the value of hwLoopLineTestDCAB is valid.
Options:
1. valid(1) -the value of hwLoopLineTestDCAB is valid
2. invalid(2) -the value of hwLoopLineTestDCA… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.98 |
| hwLoopLineTestRAGFlag Indicates whether the value of hwLoopLineTestRAG is valid.
Options:
1. valid(1) -the value of hwLoopLineTestRAG is valid
2. invalid(2) -the value of hwLoopLineTestRAG i… | column | Enumeration | .1.3.6.1.4.1.2011.6.21.1.1.1.2.1.99 |