hwDocsIf3MdCfgFmTestSignalType
HUAWEI-CMTS-MIB ·
.1.3.6.1.4.1.2011.6.180.1.1.20.29.1.13
Object
column
obsolete
r/w
Enumeration
This object is used to configure the type of the test signal in FM channels on a cable port. Options: 1.type1khzL(1) - Plays 1 KHz left-channel single tones 2.type1khzR(2) - Plays 1 KHz right-channel single tones 3.type1khzLR(3) - Plays 1 KHz stereo single tones 4.typesweepL(4) - Plays left-channel sweep tones 5.typesweepR(5) - Plays right-channel sweep tones 6.typesweepLR(6) - Plays stereo sweep tones Default:type1khzLR(3)
Context
- MIB
- HUAWEI-CMTS-MIB
- OID
.1.3.6.1.4.1.2011.6.180.1.1.20.29.1.13- Type
- column
- Access
- readwrite
- Status
- obsolete
- Parent
- hwDocsIf3MdCfgEntry
- Table
- hwDocsIf3MdCfgTable
- Siblings
- 14
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | type1khzL |
2 | type1khzR |
3 | type1khzLR |
4 | typesweepL |
5 | typesweepR |
6 | typesweepLR |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| hwdocsIf3MdCfgUsPreEqEnable This object is used to enable or disable pre-equalization
on the upstream channel represented by this table instance.
Options:
1. true(1) - enable the pre-equalization
2. false(2)… | column | Enumeration | .1.3.6.1.4.1.2011.6.180.1.1.20.29.1.1 |
| hwDocsIf3SidClusterMaxOutstandingByte This object is used to configure the maximum number of bytes that can continue to be requested through the CM using the SID cluster.
0 indicates no limit.
The configuration takes … | column | bytes Unsigned32 | .1.3.6.1.4.1.2011.6.180.1.1.20.29.1.10 |
| hwDocsIf3PeriodicRngInterval This object is used to set the interval at which the periodic ranging grant is assigned for an online CM.
Every online CM initiates a ranging request after receiving the periodic … | column | ms Unsigned32 | .1.3.6.1.4.1.2011.6.180.1.1.20.29.1.11 |
| hwdocsIf3MdCfgEqamAnnexType This attribute defines the ITU-J-83 Annex being used for this MAC Domain.
The value of this attribute indicates the conformance of the implementation to important regional cable … | column | Enumeration | .1.3.6.1.4.1.2011.6.180.1.1.20.29.1.12 |
| hwDocsIf3MdCfgFmPreEmphasis obsolete This object is used to configure the pre-emphasis of the sound signal in FM channels on a cable port.
Options:
1.off(1) - off
2.us50(2) - 50us
Default:… | column | Enumeration | .1.3.6.1.4.1.2011.6.180.1.1.20.29.1.14 |
| hwDocsIf3MdCfgNdrUsSgMode This object is used to configure the service group work mode of NDR channels on a cable port.
Options:
1. single(1) - set NDR channels to work in single service group mode.
… | column | Enumeration | .1.3.6.1.4.1.2011.6.180.1.1.20.29.1.15 |
| hwDocsIf3MdCfgUsSgMode This object is used to configure the service group work mode of upstream channels on a cable port.
Options:
1. single(1) - set MAC domain upstream channels to work in single s… | column | Enumeration | .1.3.6.1.4.1.2011.6.180.1.1.20.29.1.2 |
| hwdocsIf3MdCfgMapLeadTime This object is used to configure the lead time for map messages on a cable port.
Note: a smaller parameter value may cause some CMs to drop packets or go offline.
Default value: 0… | column | us Integer32 | .1.3.6.1.4.1.2011.6.180.1.1.20.29.1.3 |
| hwdocsIf3MdCfgMinMapTime This object is used to configure the minimum interval time for map messages on a cable port.
Note: a smaller parameter value may cause some CMs to drop packets or go offline.
Defa… | column | us Integer32 | .1.3.6.1.4.1.2011.6.180.1.1.20.29.1.4 |
| hwDocsIf3MdCfgOperation This object is used to clear the statistics of a cable port or a CM.
Options:
1.clearCablePortStat(1) - clears the cable port statistics.
2.clearAllCmStat(2) … | column | Enumeration | .1.3.6.1.4.1.2011.6.180.1.1.20.29.1.5 |
| hwDocsIf3SidClusterNumber This object is used to configure the number of SID cluster.
The configuration takes effect after the CM goes online again.
Default: 1 | column | Unsigned32 | .1.3.6.1.4.1.2011.6.180.1.1.20.29.1.6 |
| hwDocsIf3SidClusterMaxRequest This object is used to configure the maximum number of requests that can be sent by the CM using the SID cluster.
0 indicates no limit.
The configuration takes effect after the C… | column | Unsigned32 | .1.3.6.1.4.1.2011.6.180.1.1.20.29.1.7 |
| hwDocsIf3SidClusterMaxTime This object is used to configure the maximum time during which requests are sent by the CM using the SID cluster.
The time starts from the time at which the first request is sent… | column | ms Unsigned32 | .1.3.6.1.4.1.2011.6.180.1.1.20.29.1.8 |
| hwDocsIf3SidClusterMaxTotalByte This object is used to configure the maximum number of bytes that can be requested through the CM using the SID cluster, including the number of request bytes
that have been sent… | column | bytes Unsigned32 | .1.3.6.1.4.1.2011.6.180.1.1.20.29.1.9 |