snSwPortStatsOutDiscard
HP-SN-SWITCH-GROUP-MIB ·
.1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.30
Object
column
RFC1155-SMICounter
The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer space.
Context
- MIB
- HP-SN-SWITCH-GROUP-MIB
- OID
.1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.30- Type
- column
- Access
- readonly
- Status
- current
- Parent
- snSwPortInfoEntry
- Table
- snSwPortInfoTable
- Siblings
- 56
Syntax
RFC1155-SMICounter
- Source
- RFC1155-SMICounter
- Base type
Unsigned32
Values & Constraints
Type Constraints
range: 0..4294967295
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| snSwPortInfoPortNum The port index.
The bit 0 to bit 7: port number.
The bit 8 to bit 11: slot number (slot for chassis only). | column | Integer32 | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.1 |
| snSwPortInfoPortQos The Stand alone stackable switch Port Qos Priority values are:
low(0) -- low prority
high(1) -- high prority.
The BigIron Port Qos Priority values are:
level0(0), level1(1), lev… | column | Enumeration | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.10 |
| snSwPortInfoPhysAddress The port physical address. The physical address
represents the switch port. | column | PhysAddress | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.11 |
| snSwPortStatsInFrames The total number of packets received on the interface. | column | RFC1155-SMICounter | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.12 |
| snSwPortStatsOutFrames The total number of packets transmitted out of the interface. | column | RFC1155-SMICounter | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.13 |
| snSwPortStatsAlignErrors dot3StatsAlignmentErrors : A count of frames
received on a particular interface that are
not an integral number of octets in length
and do not pass the FCS check.
… | column | RFC1155-SMICounter | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.14 |
| snSwPortStatsFCSErrors dot3StatsFCSErrors : A count of frames received
on a particular interface that are an integral
number of octets in length but do not pass the
FCS check.
The coun… | column | RFC1155-SMICounter | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.15 |
| snSwPortStatsMultiColliFrames dot3StatsMultipleCollisionFrames :
A count of successfully transmitted frames on
a particular interface for which transmission
is inhibited by more than one collision.
… | column | RFC1155-SMICounter | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.16 |
| snSwPortStatsFrameTooLongs dot3StatsFrameTooLongs : A count of frames
received on a particular interface that
exceed the maximum permitted frame size.
The count represented by an instance o… | column | RFC1155-SMICounter | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.17 |
| snSwPortStatsTxColliFrames A count of successfully transmitted frames on
a particular interface for which transmission
is inhibited by more than one collision.
A frame that is counted by a co… | column | RFC1155-SMICounter | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.18 |
| snSwPortStatsRxColliFrames A count of successfully received frames on
a particular interface for which transmission
is inhibited by more than one collision. This
object is not specified in dot3 but it has … | column | RFC1155-SMICounter | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.19 |
| snSwPortInfoMonitorMode A monitoring port is selected and its traffic will be
analyzed if the mode is not disabled(0), which is
the default mode.
The values are:
disabled(0) -- No traffic … | column | Enumeration | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.2 |
| snSwPortStatsFrameTooShorts A count of frames received on a particular
interface that below the minimum permitted
frame size. | column | RFC1155-SMICounter | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.20 |
| snSwPortLockAddressCount The number of source MAC addresses are allowed
for a port. Writing 0 to this object will allow
any number of addresses. | column | Integer32 | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.21 |
| snSwPortStpPortEnable The enabled/disabled status of the port. | column | Enumeration | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.22 |
| snSwPortDhcpGateListId The ID for a DHCP gateway list entry relative
to this switch port. 0 = unset or no assigned ID | column | Integer32 | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.23 |
| snSwPortName Port Name string. | column | OctetString | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.24 |
| snSwPortStatsInBcastFrames The total number of broadcast packets received on the interface. | column | RFC1155-SMICounter | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.25 |
| snSwPortStatsOutBcastFrames The total number of broadcast packets transmitted out of the interface. | column | RFC1155-SMICounter | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.26 |
| snSwPortStatsInMcastFrames The total number of multicast packets received on the interface. | column | RFC1155-SMICounter | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.27 |
| snSwPortStatsOutMcastFrames The total number of multicast packets transmitted out of the interface. | column | RFC1155-SMICounter | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.28 |
| snSwPortStatsInDiscard The number of inbound packets which were chosen
to be discarded even though no errors had been
detected to prevent their being deliverable to a
higher-layer protocol. One possibl… | column | RFC1155-SMICounter | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.29 |
| snSwPortInfoTagMode For tagged port, we could have multiple VLANs
per port. For untagged port or auto port, there
is only one VLAN ID per port. | column | Enumeration | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.3 |
| snSwPortStatsMacStations The total number of MAC Stations connected to the interface. | column | Integer32 | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.31 |
| snSwPortCacheGroupId Cache Group ID for the interface. | column | Integer32 | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.32 |
| snSwPortTransGroupId Transparent Group ID for the interface. | column | Integer32 | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.33 |
| snSwPortInfoAutoNegotiate This feature only applies to Gigabit Ethernet ports. If set to
disable(0), port will be put to non-negotiation mode. If set to
enable(1), port will start auto-negotiation indefini… | column | Enumeration | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.34 |
| snSwPortInfoFlowControl Enable/Disbale port flow control. | column | Enumeration | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.35 |
| snSwPortInfoGigType The media type for the port. The
values are:
m1000BaseSX(0)....1Gbits per second fiber, with a short wavelength transceiver.
m1000BaseLX(1)....1Gbits per second fiber, with a … | column | Enumeration | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.36 |
| snSwPortStatsLinkChange The total number of link state change of the interface. | column | RFC1155-SMICounter | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.37 |
| snSwPortIfIndex In order to identify a particular interface, this
object shall identify the instance of the ifIndex
object, defined in RFC 1213 and RFC 1573. | column | Integer32 | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.38 |
| snSwPortDescr A textual string containing the slot/port information
about the interface. | column | DisplayString | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.39 |
| snSwPortInfoChnMode The port can be configured to operate in either
half or full duplex mode. The values are:
halfDuplex(1)...half duplex mode
fullDuplex(2)...full duplex mode
The read-back channel… | column | Enumeration | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.4 |
| snSwPortInOctets The total number of octets received on the interface,
including framing characters. This object is a 64-bit
counter of the ifInOctets object, defined in RFC 1213.
The octet stri… | column | OctetString | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.40 |
| snSwPortOutOctets The total number of octets transmitted out of the interface,
including framing characters. This object is a 64-bit
counter of the ifOutOctets object, defined in RFC 1213.
The oc… | column | OctetString | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.41 |
| snSwPortStatsInBitsPerSec The number of bits per second received on the interface
over a 5 minutes interval. | column | RFC1155-SMIGauge | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.42 |
| snSwPortStatsOutBitsPerSec The number of bits per second transmitted out of the interface
over a 5 minutes interval. | column | RFC1155-SMIGauge | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.43 |
| snSwPortStatsInPktsPerSec The number of packets per second received on the interface
over a 5 minutes interval. | column | RFC1155-SMIGauge | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.44 |
| snSwPortStatsOutPktsPerSec The number of packets per second transmitted out of the interface
over a 5 minutes interval. | column | RFC1155-SMIGauge | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.45 |
| snSwPortStatsInUtilization The input network utilization in hundredths of a percent
over a 5 minutes interval. | column | Integer32 | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.46 |
| snSwPortStatsOutUtilization The output network utilization in hundredths of a percent
over a 5 minutes interval. | column | Integer32 | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.47 |
| snSwPortFastSpanPortEnable The enabled/disabled fast span port status of the port. | column | Enumeration | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.48 |
| snSwPortFastSpanUplinkEnable The enabled/disabled fast span uplink status of the port. | column | Enumeration | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.49 |
| snSwPortInfoSpeed The speed configuration for a port. The values are:
none(0)..........link down or no traffic.
sAutoSense(1)....Auto-sensing 10 or 100Mbits.
s10M(2)..........10Mbits per seco… | column | Enumeration | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.5 |
| snSwPortVlanId The ID of a VLAN of which this port is a member. Port must
be untagged. For tagged port which belongs to multiple
VLANs, this object return 0 which is an invalid VLAN ID
value. | column | Integer32 | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.50 |
| snSwPortRouteOnly Enable/Disable L2 switching of a routing switch port.
By default, the routing switch performs routing first.
If routing failed, it performs switching. Enable route
only instrcuts … | column | Enumeration | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.51 |
| snSwPortPresent Indicate if the port is absent or present.
This object only valid for M4 module | column | Enumeration | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.52 |
| snSwPortGBICStatus Indicate if the gig port has GBICs on them.
If set to GBIC(1), it means that the port is GBIC.
If set to miniGBIC(2), it means that the port miniGBIC.
If set to empty(3), it mea… | column | Enumeration | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.53 |
| snSwPortStatsInKiloBitsPerSec Bit rate in kilobits per second received on the 10G and faster interface
over a 5 minutes interval. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.54 |
| snSwPortStatsOutKiloBitsPerSec Bit rate in kilobits per second transmitted out of the 10G and faster interface
over a 5 minutes interval. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.55 |
| snSwPortLoadInterval The time in seconds for which average port utilization should be carried out.
The value should be incremental of 30 seconds, between the ranges specified. | column | Integer32 | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.56 |
| snSwPortTagType The IEEE802.1q tag type embedded in the length/type field of
an Ethernet packet. It specifies that the 2 octets after the
length/type field in an Ethernet packet is the tag value. | column | Integer32 | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.57 |
| snSwPortInfoMediaType The media type for the port. The
values are:
other(1).........other or unknown media.
m100BaseTX(2)....100Mbits per second copper.
m100BaseFX(3)....100Mbits per second fiber… | column | Enumeration | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.6 |
| snSwPortInfoConnectorType The type of connector that the port offers.
The values are:
other(1)...........other or unknown connector
copper(2)..........Copper connector
fiber(3)...........Fiber connector… | column | Enumeration | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.7 |
| snSwPortInfoAdminStatus The desired state of all ports. The
testing(3) state indicates that no operational
packets can be passed.
(same as ifAdminStatus in MIB-II) | column | Enumeration | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.8 |
| snSwPortInfoLinkStatus The current operational state of the interface.
The testing(3) state indicates that no operational
packets can be passed.
(same as ifOperStatus in MIB-II) | column | Enumeration | .1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.9 |