hpicfXcvrMdiPairCCableStatus
HP-ICF-TRANSCEIVER-MIB ·
.1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.52
Object
column
Enumeration
This object indicates the cable diagnostics
test status on the cable pair.
Normal = No cable fault detected.
Open = Lack of continuity between ends.
Short = Short detected.
Impedance Mismatch =
- Cable pair is not connected properly or
- Cable pair is damaged or
- Connector is faulty.
Failed = TDR test failed on cable pair.
Unspecified : This object is unavailable or not reported.
As reported through cable diagnostics.
The value of this object is valid when the value of
the hpicfXcvrDiagnostics object is VCT or other.
Context
- MIB
- HP-ICF-TRANSCEIVER-MIB
- OID
.1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.52- Type
- column
- Access
- readonly
- Status
- current
- Parent
- hpicfXcvrInfoEntry
- Table
- hpicfXcvrInfoTable
- Siblings
- 64
Syntax
Enumeration
Values & Constraints
Enumerated Values
0 | normal |
1 | short |
2 | open |
3 | failed |
4 | impedanceMismatch |
5 | unspecified |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| hpicfXcvrPortIndex The interface number for this entry. | column | Integer32 | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.1 |
| hpicfXcvrDiagnosticsUpdate This object will cause specific actions
depending on the diagnostic support of the
transceiver.
Transceiver Diagnostic support:
None : No action tak… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.10 |
| hpicfXcvrTemp This is transceiver internal temperature
in thousandths of degrees Celsius.
As an example: 49120 is 49.120 degrees Celsius.
The value of this object … | column | thousandths of degrees Celsius SNMPv2-SMIInteger32 | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.11 |
| hpicfXcvrVoltage This is transceiver supply voltage
in hundreds of microvolts.
As an example: 32928 is 3.2928 volts.
Will be zero if the transceiver does not report
t… | column | hundreds of microvolts Unsigned32 | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.12 |
| hpicfXcvrBias This is Tx bias current in microamps.
The value of this object is valid when the value of
the hpicfXcvrDiagnostics object is DOM. | column | microamps Unsigned32 | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.13 |
| hpicfXcvrTxPower This is transmit output power
in thousandths of dBm.
As an example: -5840 is -5.840dBm.
-in dBm (0 microwatts) will be reported as -99999999.
… | column | thousandths of dBm SNMPv2-SMIInteger32 | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.14 |
| hpicfXcvrRxPower This is received optical power
in thousandths of dBm.
As an example: -5840 is -5.840dBm.
-in dBm (0 microwatts) will be reported as -99999999.
… | column | thousandths of dBm SNMPv2-SMIInteger32 | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.15 |
| hpicfXcvrAlarms Bitmask indicating transceiver alarms,
Rx power low warning(0)
Rx power high warning(1)
Tx power low warning(2)
Tx power high warning(3)
Tx bias low warning(4)
Tx bias high warnin… | column | Bits | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.16 |
| hpicfXcvrErrors Bitmask indicating transceiver errors.
Transceiver information I/O error(0)
Transceiver information checksum error(1)
Transceiver type and port configuration mismatch(2)
Transceiv… | column | Bits | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.17 |
| hpicfXcvrTempHiAlarm Transceiver temperature high alarm
threshold limit in thousandths of degrees Celsius.
As an example: 49120 is 49.120 degrees Celsius.
The value of th… | column | thousandths of degrees Celsius SNMPv2-SMIInteger32 | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.18 |
| hpicfXcvrTempLoAlarm Transceiver temperature low alarm
threshold limit in thousandths of degrees Celsius.
As an example: 49120 is 49.120 degrees Celsius.
The value of thi… | column | thousandths of degrees Celsius SNMPv2-SMIInteger32 | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.19 |
| hpicfXcvrPortDesc A textual description of the interface. | column | OctetString | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.2 |
| hpicfXcvrTempHiWarn Transceiver temperature high warning
threshold limit in thousandths of degrees Celsius.
As an example: 49120 is 49.120 degrees Celsius.
The value of … | column | thousandths of degrees Celsius SNMPv2-SMIInteger32 | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.20 |
| hpicfXcvrTempLoWarn Transceiver temperature low warning
threshold limit in thousandths of degrees Celsius.
As an example: 49120 is 49.120 degrees Celsius.
The value of t… | column | thousandths of degrees Celsius SNMPv2-SMIInteger32 | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.21 |
| hpicfXcvrVccHiAlarm Transceiver VCC high alarm
threshold limit in hundreds of microvolts.
As an example: 32928 is 3.2928 volts.
Returns zero if not supported on the tran… | column | hundreds of microvolts Unsigned32 | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.22 |
| hpicfXcvrVccLoAlarm Transceiver VCC low alarm
threshold limit in hundreds of microvolts.
As an example: 32928 is 3.2928 volts.
Returns zero if not supported on the trans… | column | hundreds of microvolts Unsigned32 | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.23 |
| hpicfXcvrVccHiWarn Transceiver VCC high warning
threshold limit in hundreds of microvolts.
As an example: 32928 is 3.2928 volts.
Returns zero if not supported on the tr… | column | hundreds of microvolts Unsigned32 | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.24 |
| hpicfXcvrVccLoWarn Transceiver VCC low warning
threshold limit in hundreds of microvolts.
As an example: 32928 is 3.2928 volts.
Returns zero if not supported on the tra… | column | hundreds of microvolts Unsigned32 | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.25 |
| hpicfXcvrBiasHiAlarm Transceiver bias high alarm
threshold limit in microamps.
The value of this object is valid when the value of
the hpicfXcvrDiagnostics object is DOM. | column | microamps Unsigned32 | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.26 |
| hpicfXcvrBiasLoAlarm Transceiver bias low alarm
threshold limit in microamps.
The value of this object is valid when the value of
the hpicfXcvrDiagnostics object is DOM. | column | microamps Unsigned32 | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.27 |
| hpicfXcvrBiasHiWarn Transceiver bias high warning
threshold limit in microamps.
The value of this object is valid when the value of
the hpicfXcvrDiagnostics object is DOM. | column | microamps Unsigned32 | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.28 |
| hpicfXcvrBiasLoWarn Transceiver bias low warning
threshold limit in microamps.
The value of this object is valid when the value of
the hpicfXcvrDiagnostics object is DOM. | column | microamps Unsigned32 | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.29 |
| hpicfXcvrModel A textual description of the transceiver
model number. | column | OctetString | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.3 |
| hpicfXcvrPwrOutHiAlarm Transceiver transmit power high alarm
threshold limit in tenths of microwatts.
As an example: 10000 is 1 milliwatt.
The value of this object is valid… | column | tenths of microwatts Unsigned32 | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.30 |
| hpicfXcvrPwrOutLoAlarm Transceiver transmit power low alarm
threshold limit in tenths of microwatts.
As an example: 10000 is 1 milliwatt.
The value of this object is valid … | column | tenths of microwatts Unsigned32 | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.31 |
| hpicfXcvrPwrOutHiWarn Transceiver transmit power high warning
threshold limit in tenths of microwatts
As an example: 10000 is 1 milliwatt.
The value of this object is vali… | column | tenths of microwatts Unsigned32 | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.32 |
| hpicfXcvrPwrOutLoWarn Transceiver transmit power low warning
threshold limit in tenths of microwatts.
As an example: 10000 is 1 milliwatt.
The value of this object is vali… | column | tenths of microwatts Unsigned32 | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.33 |
| hpicfXcvrRcvPwrHiAlarm Transceiver receive power high alarm
threshold limit in tenths of microwatts.
As an example: 10000 is 1 milliwatt.
The value of this object is valid … | column | tenths of microwatts Unsigned32 | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.34 |
| hpicfXcvrRcvPwrLoAlarm Transceiver receive power low alarm
threshold limit in tenths of microwatts.
As an example: 10000 is 1 milliwatt.
The value of this object is valid w… | column | tenths of microwatts Unsigned32 | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.35 |
| hpicfXcvrRcvPwrHiWarn Transceiver receive power high warning
threshold limit in tenths of microwatts.
As an example: 10000 is 1 milliwatt.
The value of this object is vali… | column | tenths of microwatts Unsigned32 | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.36 |
| hpicfXcvrRcvPwrLoWarn Transceiver receive power low warning
threshold limit in tenths of microwatts.
As an example: 10000 is 1 milliwatt.
The value of this object is valid… | column | tenths of microwatts Unsigned32 | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.37 |
| hpicfXcvrDiagnosticsTimeStamp deprecated ********* THIS OBJECT IS DEPRECATED *********
A textual description of the diagnostics
information updated for the last time in the
transceiver.
This… | column | OctetString | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.38 |
| hpicfXcvrPhyLinkStatus This object indicates the link status as reported
by the physical entity.
The value of this object is valid when the value of
the hpicfXcvrDiagnostics object is VC… | column | Enumeration | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.39 |
| hpicfXcvrSerial A textual description of the transceiver
serial number. | column | OctetString | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.4 |
| hpicfXcvrPhySpeed This object indicates the speed in Mbps as reported
by the physical entity.
Will be zero if speed and duplex are unresolved.
The value of this objec… | column | megabits per second Unsigned32 | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.40 |
| hpicfXcvrPhyDuplex This object indicates the duplex as reported by
the physical entity.
Will be unspecified if speed and duplex are unresolved.
The value of this object… | column | Enumeration | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.41 |
| hpicfXcvrMdiPairACableStatus This object indicates the diagnostics
test status on the cable pair.
Normal = No cable fault detected.
Open = Lack of continuity between ends.
Short = Short detecte… | column | Enumeration | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.42 |
| hpicfXcvrMdiPairACableLength This object indicates the cable pair length in
meters as reported by cable diagnostics.
A gigabit link must be present for this object
to be non zero.
… | column | meters Unsigned32 | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.43 |
| hpicfXcvrMdiPairADistanceToFault This object indicates the distance in meters to
a fault in the cable pair as reported through cable
diagnostics.
Will be zero if no fault or the transceiver does no… | column | meters Unsigned32 | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.44 |
| hpicfXcvrMdiPairAPolaritySwap This object indicates if the cable pair connected
to the phy is inverted as reported through cable
diagnostics.
Will be unspecified if the this object is unavailabl… | column | Enumeration | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.45 |
| hpicfXcvrMdiPairASkew This object indicates the delay skew in nanoseconds
of this cable pair and the fastest cable pair as
reported through cable diagnostics.
Will be zero if the lowest… | column | nanoseconds Unsigned32 | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.46 |
| hpicfXcvrMdiPairBCableStatus This object indicates the cable diagnostics
test status on the cable pair.
Normal = No cable fault detected.
Open = Lack of continuity between ends.
Short = Short d… | column | Enumeration | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.47 |
| hpicfXcvrMdiPairBCableLength This object indicates the cable pair length in
meters as reported by cable diagnostics.
A gigabit link must be present for this object
to be non zero.
… | column | meters Unsigned32 | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.48 |
| hpicfXcvrMdiPairBDistanceToFault This object indicates the distance in meters to
a fault in the cable pair as reported through cable
diagnostics.
Will be zero if no fault or the transceiver does no… | column | meters Unsigned32 | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.49 |
| hpicfXcvrType A textual description of the transceiver type. | column | OctetString | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.5 |
| hpicfXcvrMdiPairBPolaritySwap This object indicates if the cable pair connected
to the phy were inverted as reported through cable
diagnostics.
Will be unspecified if the this object is unavaila… | column | Enumeration | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.50 |
| hpicfXcvrMdiPairBSkew This object indicates the delay skew in nanoseconds
of this cable pair and the fastest cable pair as
reported through cable diagnostics.
Will be zero if the lowest… | column | nanoseconds Unsigned32 | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.51 |
| hpicfXcvrMdiPairCCableLength This object indicates the cable length in meters
of the cable pair as reported through cable
diagnostics.
A gigabit link must be present for this object
to be non … | column | meters Unsigned32 | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.53 |
| hpicfXcvrMdiPairCDistanceToFault This object indicates the distance in meters to
a fault in the cable pair as reported through cable
diagnostics.
Will be zero if there is no fault or the
transceiv… | column | meters Unsigned32 | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.54 |
| hpicfXcvrMdiPairCPolaritySwap This object indicates if the cable pair connected
to the phy were inverted as reported through cable
diagnostics.
Will be unspecified if the this object is unavaila… | column | Enumeration | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.55 |
| hpicfXcvrMdiPairCSkew This object indicates the delay skew in nanoseconds
of this cable pair and the fastest cable pair as
reported through cable diagnostics.
Will be zero if the lowest… | column | nanoseconds Unsigned32 | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.56 |
| hpicfXcvrMdiPairDCableStatus This object indicates the cable diagnostics
test status on the cable pair.
Normal = No cable fault detected.
Open = Lack of continuity between ends.
Short = Short d… | column | Enumeration | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.57 |
| hpicfXcvrMdiPairDCableLength This object indicates the cable length in meters
of the cable pair as reported through cable
diagnostics.
A gigabit link must be present for this object
to be non … | column | meters Unsigned32 | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.58 |
| hpicfXcvrMdiPairDDistanceToFault This object indicates the distance in meters to
a fault in the cable pair as reported through cable
diagnostics.
Will be zero if no fault or the transceiver does no… | column | meters Unsigned32 | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.59 |
| hpicfXcvrConnectorType A textual description of the transceiver
connector type. | column | OctetString | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.6 |
| hpicfXcvrMdiPairDPolaritySwap This object indicates if the cable pair connected
to the phy were inverted as reported through cable
diagnostics.
Will be unspecified if the this object is unavaila… | column | Enumeration | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.60 |
| hpicfXcvrMdiPairDSkew This object indicates the delay skew in nanoseconds
of this cable pair and the fastest cable pair as
reported through cable diagnostics.
Will be zero if the lowest… | column | nanoseconds Unsigned32 | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.61 |
| hpicfXcvrMdiPairABSwap This object indicates the if the channels are
swapped for channels A and B as reported through
cable diagnostics.
MDI : Channel A received on MDI[1], Channel B on … | column | Enumeration | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.62 |
| hpicfXcvrMdiPairCDSwap This object indicates if the channels are
swapped for channels C and D as reported through
cable diagnostics.
MDI : Channel C received on MDI[3], Channel D on MDI[… | column | Enumeration | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.63 |
| hpicfXcvrDiagnosticsTimeTicks The value of sysUpTime of when this diagnostic
information was last updated. If this diagnostic
information was never updated, then this object
will contain a zero value. | column | centi-seconds SNMPv2-SMITimeTicks | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.64 |
| hpicfXcvrManufacDate A textual description of the transceiver
Manufacturing date. | column | OctetString | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.65 |
| hpicfXcvrWavelength A textual description of the central optical
wavelength.
n/a will be reported for copper transceivers. | column | OctetString | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.7 |
| hpicfXcvrTxDist A textual description of the link length
supported by the transceiver. | column | OctetString | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.8 |
| hpicfXcvrDiagnostics This object indicates transceiver diagnostic support.
May be one of Virtual Cable Test (VCT), Diagnostic
Optical Monitoring (DOM), other or none. | column | Enumeration | .1.3.6.1.4.1.11.2.14.11.5.1.82.1.1.1.1.9 |