configSnoopingPorts
G6-IGMP-MIB ·
.1.3.6.1.4.1.3181.10.6.2.40.5.1.5
Object
This parameter permits port selective IGMP/MLD snooping enabling. When empty all ports are enabled! Syntax: slot/port, slot/port or use hex value for quick setup. Example: = 0xf (ports 1-4)
Context
- MIB
- G6-IGMP-MIB
- OID
.1.3.6.1.4.1.3181.10.6.2.40.5.1.5- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- configEntry
- Table
- configTable
- Siblings
- 15
Syntax
SNMPv2-SMIInteger32
- Source
- SNMPv2-SMIInteger32
- Base type
Integer32
Values & Constraints
Type Constraints
range: -2147483648..2147483647
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| configIndex Automatically generated | column | Integer32 | .1.3.6.1.4.1.3181.10.6.2.40.5.1.1 |
| configMcastGroupLimit Indicates the number of multicast groups in the table. | column | Integer32 | .1.3.6.1.4.1.3181.10.6.2.40.5.1.10 |
| configGroupMembershipInterval IGMP group_membership_interval time in seconds. | column | Integer32 | .1.3.6.1.4.1.3181.10.6.2.40.5.1.11 |
| configMaxResponseTime IGMP response time in seconds. | column | Integer32 | .1.3.6.1.4.1.3181.10.6.2.40.5.1.12 |
| configEnableFastLeave Enables the software to remove the multicast group when it receives an IGMP leave report without first sending an IGMP query message to check if other users still require this gro… | column | Enumeration | .1.3.6.1.4.1.3181.10.6.2.40.5.1.13 |
| configLastMemberQueryTime Sets the interval in seconds that the software waits after sending an IGMP query to verify that no hosts that want to receive a particular multicast group to remain on a network s… | column | Integer32 | .1.3.6.1.4.1.3181.10.6.2.40.5.1.14 |
| configNeighborDeadInterval IGMP neighbor dead interval in seconds in case of router_discovery mode. | column | Integer32 | .1.3.6.1.4.1.3181.10.6.2.40.5.1.15 |
| configRouterAgingTime IGMP router aging time in seconds. | column | Integer32 | .1.3.6.1.4.1.3181.10.6.2.40.5.1.16 |
| configVlanId Defines IGMP snooping table entry associated with this VLAN ID. This is the key value for the table.VLAN ID 0 is used to define the IGMP settings when VLANs are not used. Type '=:… | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.3181.10.6.2.40.5.1.2 |
| configEnableIgmpSnooping Enable IGMP (IPv4) snooping for this particular VLAN. | column | Enumeration | .1.3.6.1.4.1.3181.10.6.2.40.5.1.3 |
| configEnableMldSnooping Enable MLD (IPv6) snooping for this particular VLAN. | column | Enumeration | .1.3.6.1.4.1.3181.10.6.2.40.5.1.4 |
| configStaticRouterPorts When set corresponding ports will be marked as static router ports. Upon default no ports will be marked. Syntax: slot/port, slot/port or use hex value for quick setup. Example: =… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.3181.10.6.2.40.5.1.6 |
| configMulticastRouterDetection Defines the mode for detecting the router port. | column | Enumeration | .1.3.6.1.4.1.3181.10.6.2.40.5.1.7 |
| configEnableReportAggregation When enabled limits the number of reports received from same subnet to be transmitted only once to the router. | column | Enumeration | .1.3.6.1.4.1.3181.10.6.2.40.5.1.8 |
| configEnableFloodingUnregisterPkt When enabled unregistered multicast streams are flooded on all ports (which are member of the source VLAN of this stream). When disabled unregistered multicast streams are forward… | column | Enumeration | .1.3.6.1.4.1.3181.10.6.2.40.5.1.9 |