powersave-enable-type
FUTURESMART-MIB ·
.1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.89
Object
scalar
optional
r/w
Enumeration
ePowerSaveOff - printer stays awake all the time, can only sleep if sleep button is hit. ePowerSaveUseSleepDelay - use sleep delay the old way, sleep schedule is ignored . ePowerSaveUseSleepSchedule - sleep delay time is ignored, stay awake in wake period, sleep in 15 minutes in sleep period. ePowerSaveMaximize - set the sleep delay to 15 minutes, so wether in wake or sleep period it will sleep in 15 minutes. ePowerSaveCustom - set the sleep delay to 45 minutes, use sleep delay during wake period, sleep in 15 minutes in sleep period.
Context
- MIB
- FUTURESMART-MIB
- OID
.1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.89- Type
- scalar
- Access
- readwrite
- Status
- optional
- Parent
- settings-system
- Siblings
- 12
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | ePowerSaveOff |
2 | ePowerSaveUseSleepDelay |
3 | ePowerSaveUseSleepSchedule |
4 | ePowerSaveMaximize |
5 | ePowerSaveCustom |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| energy-star optional Returns or changes the Energy Star sleep value. If the value
is greater than zero, then the device will go into energy
saving sleep mode after the print engine has been idle for t… | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.1 |
| enable-engine-early-warmup optional This PML object is used by HP SW to enable/disable the printer
to send the signal of warm-up process early to engine. The
effect of warming up early will reduce the First Page Out… | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.101 |
| sleep-mode optional Returns eTrue if the device is in energy saving sleep mode,
otherwise returns eFalse. Setting SLEEP-MODE to eFalse causes
the device to wake up, if it is in sleep mode. Setting
SL… | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.2 |
| date-display optional Controls front-panel date display format. | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.22 |
| mono-color-switching-mode optional This object allows the user to view/change the color/mono
switching mode for a device | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.31 |
| device-configure | node | - | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.32 |
| direct-connect-ports-enable optional This object specifies whether all direct connect ports
(parallel and USB) are available or ignored. JetDirect,
embedded network connectivity, and third party add-on cards
(such as… | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.43 |
| power-state optional This object is used to inquire about and to control the 'power
state' of the device. The exact meaning of each enumeration may
vary from device to device, but the general interpre… | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.65 |
| factory-reset optional writing an INTEGER 0 will do factory reset on system variables,
MFP Settings and the .NET database without a reboot. | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.68 |
| order-cartridge optional Used to enable/disable the supplies status message that is
shown when the supply reaches low | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.71 |
| large-size-media-default-grain-direction optional This object identifies default grain direction for large size
media (B/A3) only. Default value is eShortGrain | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.97 |
| start-engine-early-warmup mandatory This PML object is used by HP SW drivers to signal the printer
that a job is coming, and to start the warm-up process
early.The effect of warming up early will reduce the First Pa… | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.99 |